RF / Microwave Switches
-
Product
PXI Hex SPDT RF Switch 3GHz 50 SMB
40-870-006
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
LXI Microwave Multiplexer, SP6T, 5-Bank, 50GHz, 50Ω, SMA-2.4
60-800-605
Microwave Multiplexer
Our 60-800-605 is a 5 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
Optical Switch
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, FC/PC Connectors, With Interlock
42-860A-122-HI
Switch Module
The 40/42-860A-122-HI is a PXI/PXIe dual insert/bypass switch with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable
150275-01
Switch Cable
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
Product
LXI Microwave Multiplexer, SP6T, 11-Bank, 67GHz, 50Ω, SMA-1.85
60-800-811
Microwave Multiplexer
Our 60-800-811 is a 11 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Automated Optical Switch - MATRIQ
Optical Switch
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-332
Switch Module
The 40/42-860A-332 is a PXI/PXIe triple insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
MSP Switch Probes
Switch Probe
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
-
Product
1.5-m, 78-pin Dsub Cable
Y1137A
Switch Cable
The Y1137A is a M/F twisted-pair cable with outer shield. The 300-V cable provides a direct connection for the Keysight multifunction switch / measure mainframe and modules. Some modules require two cables.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-1m
RF Cable Assembly
This 1m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, SMB
42-870A-006
Switch Module
The 40-870A-006 (PXI) and 42-870A-006 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
High Density SPDT Plug-In Switch Card
1260-116
Switch Card
The Astronics 1260-116 is a 24-channel, Form C, single-pole double-throw (SPDT) switch card for use in either the 1260-100 VXI Carrier or the 1256 GPIB/RS-232 Switching Mainframe.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-782B-552
Switch Module
The 40-782B-552 (PXI) and 42-782B-552 (PXIe) dual failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
Product
12-Ch SPST 5A-250VAC High Current Power Switching
YAV90CIN
Switch Module
12 Independent SPST relaysSwitching up to 5A 250Vac12 current measurement channelsGeneral inhibit inputCAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
Product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-C180-3
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
PXI Single Microwave Transfer Switch 18GHz 50 SMA
40-782A-521
Switch Module
The 40-782A-521 is a single transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
42-880B-004
Switch Module
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
Product
PXI Source Switching Module
40-618-001
Switch Module
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
Product
Switch Modules - 16 Single Pole, Form C, Discrete Relays which are Wired & Controlled Individually
JX16/KC
Switch Module
This module has 16 single pole, Form C, discrete relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. It is available with Type S or M reed relays.
-
Product
PXI 8-Slot BRIC Matrix, 44x16 1-Pole (4 sub-cards)
40-562B-121-44X16
Matrix Switch Module
The 40-562B-121-44X16 is a high density BRIC8 matrix module with a size of 44x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-F180-1
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI 4-Slot BRIC Matrix, 110x8 2-Pole (5 sub-cards)
40-562B-022-110X8
Matrix Switch Module
The 40-562B-022-110X8 is a high density BRIC4 matrix module with a size of 110x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4-Slot BRIC Matrix, 66x8 1-Pole (3 Sub-cards)
40-562B-021-66X8
Matrix Switch Module
The 40-562B-021-66X8 is a high density BRIC4 matrix module with a size of 66x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Single 33x8 Matrix 2-Pole 1A
40-581-002
Matrix Switch Module
The Worlds highest density 2-pole single slot 3U PXI Matrix Module, the 40-581has 264 crosspoints configured as a 2-pole 33x8 matrix. The use of high density electromechanical relays means that the 40-581 is a low cost high density matrix solution with current handling up to 1 Amp. The 40-581 module is suitable for matrix applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based matrices do not have sufficient power handling capability.
-
Product
PXI 2 Slot BRIC 116x6 2A 1-Pole Matrix
40-596-202
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 450x4, 6 Sub-cards
40-568A-106
Matrix Switch Module
The 40-568A-106 is a PXI 1-pole 450x4 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8 Slot BRIC Solid State 96x8 1-Pole (3 sub-cards)
40-563A-121-96X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
