D-Sub
D-Subminature Connector Also known as: DSub
-
Product
26-Pin D-Type Female Right Angled PCB
40-963-026-RF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
PCI Express Digital I/O Boards
PEX-P8R8I
-
PCI Express Board with 8 Isolated Digital Inputs and 8 Relay Outputs. Includes one CA-4002 D-Sub connector and Software Development Kit with Demo Programs
-
Product
PCI Digital I/O Boards
PISO-C64
-
The PISO-C64 has 64-channels of optically isolated digital outputs, arranged into two isolated banks. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated output channels are designed into group C and Group D. The power supply of the input port may use external power or the power from the PC side using DC/DC converter. The power supply of the output port should use external power. This interface board is easily installed in any PC/AT/XT compatible computer. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-C64 has one 37-pin D-Sub Connector and one 40-pin male header. Users can connect the digital signal through the second D-Sub connector. Each D-Sub connector contains 32 output channels.
-
Product
Cable Assembly, Receiver, TriPaddle/Micro Coax, 36", 2 9-Pin Female D-Subs, and 2 SMB Plugs
540278010259
Cable Assembly
Cable Assembly, Receiver, TriPaddle/Micro Coax, 36", 2 9-Pin Female D-Subs, and 2 SMB Plugs.
-
Product
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
540142020240
Cable Assembly
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
-
Product
3-Pin Power D-Type Connector, 40A, Female PCB Mount
40-963-003-RF
D-Sub PCB-Mount Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
14-Pin D-SUB Male to 6 1-Pin BNC Female, 20 cm, Breakout Trigger Cable
149055-0R2
-
Chassis DSUB Trigger Breakout Cable to 6 BNC for PFI 0-3, Remote Inhibit, & Fault, 20 cm
-
Product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
D-Sub Female Connector Block
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
9-Pin D-SUB Female to Industrial Ethernet (IXB) Female, 0.5 m, Pass-Through, Shielded Analog Cable
135852-0R5
Switch Cable
SHDB9F-IXBF Straight Passthrough Cable With Thumbscrews, 0.5 Meters
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair
540149050201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair.
-
Product
Micro Dsub GPIB Cable Adapter For PZ2100A (0.25m)
GPIB Cable
The Keysight PX0110A converts MicroD25 GPIB to standard GPIB. It supports the Keysight PZ2100A.Standard GPIB to MicroD25 Cable length: 0.25 meter Compatible with the PZ2100A
-
Product
PCI Daughter Boards
DB-8225/2 (with 2 meter D-Sub 37-pin cable)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
Board Accessories
DN-37A (with Din Rail Mount and Male-Female D-Sub Cable)
-
DN-37 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with a 37-Pin I/O Connector and 37-pin CA-3710 cable.
-
Product
9-Pin D-Type Connector Block
92-965-009-F
D-Sub Female Connector Block
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
Product
PCI Daughter Boards
DB-24POR/D (with D-Sub cable)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
General Purpose Switch
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
D-Sub PCB-Mount Connector
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
1.5-m, 78-pin Dsub Cable
Y1137A
Switch Cable
The Y1137A is a M/F twisted-pair cable with outer shield. The 300-V cable provides a direct connection for the Keysight multifunction switch / measure mainframe and modules. Some modules require two cables.
-
Product
Chassis For 3.5" SBC
ACK-5000
-
3.5" SBC chassis supports front & side I/O interfacesFan-based design with optional wall-mount & DIN rail bracketBottom door design for easy access on M.2 devices on 3.5" SBCFlexible cutouts I/O in the front & right-hand side: up to 7x D-SUB for COM/ GPIO/CANBus, 2x USB 2.0, 2x Audio JackEasy assembly and maintenance with standard 3.5" SBC without customizationsSupports Standard 3.5" SBC: MIO-5152, MIO-5377/R, MIO-5154, MIO-5354, MIO-5355
-
Product
PCI Daughter Boards
DB-24PR/24/DIN (with DIN-Rail mounting kit)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Connector, 104-Pin D-Type Male, PCB Mount, Right Angle, 4-40 UNC
40-963-104-RM
D-Sub PCB-Mount Connector
This 104-pin male D-type connector allows users to create their own connection solutions. Right angled PCB mounting - supplied with 4-40 UNC screwlocks. This connector is not suitable for direct connection to Pickering modules that use the 104-pin D-type connector.
-
Product
CANBus Communication
PISO-CAN400U-D
-
The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suit for networking "intelligent" devices as well as sensors and actuators within a system or sub-system. In CAN networks, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As standalone CAN controller, PISO-CAN400/CAN200 can represents an economic solution of an active CAN board. It has two or four independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PISO-CAN400/CAN200 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in a 5V PCI slot and supported truly “Plug & play”.
-
Product
PCI Daughter Boards
DB-24POR/D/DIN (D-Sub cable and DIN-Rail mounting kit)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
PCI Daughter Boards
DB-24R/24 (24V)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Breakout Box
T1000-62HD
-
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
Product
25-Pin D-SUB Female to 25-Pin D-SUB Female Multifunction Cable
782015-01
Multifunction Cable
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 1 m
