Shock
A shock test transmits kinetic or thermal energy into a UUT in a relatively short interval in a controlled enviroment.
See Also: Thermal Shock, Vibration
-
product
Thermal Shock Chambers
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
product
IEC60884-1 Low Temperature Thermal Shock Test Device
CX-DWC
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 Uses: It is used to evaluate the impact resistance of electrical accessories under low temperature conditions, and also to evaluate the low temperature impact resistance of wire and cable.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Shock Response Spectrum (SRS) Analysis Solution
Shock Response Spectrum (SRS) Analysis SolutionMechanical shock pulses are often analyzed in terms of the shock response spectrum. The shock response spectrum assumes that the shock pulse is applied as a base input to an array of independent single-degree-of-freedom systems. SDOF system assumes that each system hat its own natural frequency.
-
product
Environmental Shock Simulation Machine For Drop Testing
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
product
Pneumatic Horizontal Shock Test System
KRD12 series
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Shock Testers
Shock test data is key information when determining if your product is capable of withstanding its intended distribution and use environment. For any mechanical shock testing application, Lansmont builds a Shock Test System to meet your needs.
-
product
Vibration/Shock Testing
Quest Engineering Solutions provides a broad range of vibration testing and shock testing services. We have a variety of vibration test systems of different sizes and broad test capabilities. Vibration and shock testing and vibration analysis are important to achieving product quality. Our experience can help you choose the tests which will optimize your product's design and reliability.
-
product
Shock Test Apparatus
SCR Elektroniks make Shock test Apparatus is used to test the Electrical accessories / appliances for their mechanical strength. A wooden base fixed to a concrete block and a wooden platform is hinged base. This platform carries a wooden board, which can be fixed at various distance from the hinge and two vertical positions. The end of board bears a metal stop plate, which rests on coiled spring having constant 25N/mm.
-
product
Thermal Shock Test Chamber
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
product
Shock & Drop Testing
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
product
Thermal Shock Test Chamber (3 Zone)
Guangdong Test EQ Equipment co., Ltd.
- Divided into a high-temperature zone, low-temperature zone, and test zone. The test product is placed in the test zone, and the temperature from the high-temperature zone or low-temperature zone is applied to the test zone for thermal shock. The test product remains static during the test.- Equiped with a touch-screen control interface for easy operation.- Temperature is transferred to the test zone using a wind route switching method to perform thermal shock testing.- The maximum duration of high-temperature or low-temperature shock can reach 999 hours, and the maximum cycle period can reach 9999 cycles.- The system can operate in automatic cycle mode or manually select specific shocks. It can be set to perform two-zone or three-zone shocks, as well as cold-to-hot or hot-to-cold transitions.- The cooling system utilizes a dual refrigeration system, providing fast cooling. Water cooling is employed as the cooling method.- Testing can be performed at room temperature.
-
product
High and Low Temperature Thermal Shock Chamber
HLST-500D
The specimen is placed in test chamber specimen which cannot be placed in high temperature chamber or low temperature chamber. High temperature chamber pre-heats the air and low temperature air chamber pre-cools the air. When doing the test of temperature changing from high to low, the low temperature chamber will blow the pre-cooled air to the test chamber. Then, the air in test chamber will reach your target temperature in several minutes (“recover time”). When doing the test of temperature changing from low to high, the high temperature chamber will blow the pre-heated air to the test chamber. Then the air in test chamber will reach your target temperature within the recover time.
-
product
Thermal Shock Test Chamber (Three Zone)
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
product
Shock and Vibration Testing
E-Labs Shock and Vibration Department can perform testing on a wide range of components such as military, aerospace or automotive. The testing can be performed at ambient or extreme temperature conditions to meet any test requirements.
-
product
Rain Penetration And Thermal Shock Tester
RAST
This is a user-friendly, three-in-one test stand for your operating convenience. Internal and external shock tests as well as rain penetration tests are all important for determining the quality and durability of your products and meeting all relevant international standards.
-
product
Thermal Shock Test Chambers
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
product
Compact Accelerometer (Shock Meter)
AP2019
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
-
product
Horizontal Thermal Shock Test Chamber (2 Zone)
Guangdong Test EQ Equipment co., Ltd.
- Integral structure,the internal overall TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism.- The use of Chinese color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box independently developed special software, with automatic, intelligent, human control and other characteristics.- TESTEQ patent "Cold and heat balance technology",low temperature constant temperature season can be more than 30%.- Control mode: constant operation mode, program operation mode.- Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions.
-
product
Shock Test System, Battery Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
product
Vibration / Shock / Noise & Thermal Control
We specialise in vibration damping and shock isolation solutions for electronics and other light load applications.Our soft gel vibration damping materials are designed for isolating very light componets and extreme temperature environments.Most of our products are held in stock to support engineers with urgent vibration damping, noise control, shock isolation and cushioning impact problems.Our shock and vibration solutions are currently in use in aerospace, rail, truck, bus and handheld applications.
-
product
General Purpose
Columbia Research Laboratories
This group of accelerometers is made up of the 3000 and 5000 Series. The 3000 Series are standard size units, including many with all welded construction, that are hermetically sealed for use in dirty and humid environments. The 5000 Series are smaller and lighter in weight than standard units. Characteristics are almost identical except that with miniature units higher natural frequencies and shock levels can be obtained due to their inherently reduced mass. Sensitivities, however are somewhat lower. High Temperature models are available that operate to +500°F. For best performance use with the Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
Fire Suppression/Detection
Dexter's sensitive yet rugged fire detectors, or fire sensors, serve as the foundation of US combat fire suppression systems on combat aircraft and ground vehicles ranging from the HUMVEE to the Abraham's Tank. Our fire sensors consume low energy, making them the premier safety component on battery-powered as well as hot-wired systems. We like to call them "the eye that never sleeps." How fast are they? Fast enough to race the fire caused by a rocket hitting a fuel tank and win, triggering fire suppression on the spot to help protect soldier and pilot alike. Rugged missions require rugged equipment. Intensive MIL-STD-883H testing performed by Trialon Corporation, an independent testing facility, confirm that Dexter Research's silicon-based temperature sensor detectors meet the same rugged requirements of 1,000G's for mechanical shock and 30G's in random vibration for which our thin-film detectors are famous. Download Dexter's report here (PDF).
-
product
Sensors for Mobile Machines
*Inclination sensors with CAN or analog interface*Inductive sensors with high protection rating*Pressure sensors with a robust measuring cell for mobile hydraulics*High shock and vibration resistance*Wide operating temperature range
-
product
Type 12R2, 9U, 19" Rackmount, MIL-Rugged, Vertical
12R2-9U-V
The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
product
Car in Cold Temperature Shock Chamber
Dongguan City Simplewell Technology Co. Ltd.
Car in Cold Temperature Shock Chamber by Simplewell
-
product
Viscoelastic Shock Absorbers
This series is the interesting addition to ACE's security portfolio. Simple and compact in design, durable and maintenance-free in operation, these dampers are effective alternatives to existing emergency stop solutions.
-
product
COMPACT ACCELEROMETER
AP 1019
The compact accelerometers AP1019 (AP19) are intended for measuring vibration and shock acceleration when integrated in portable or stationary diagnostic systems for laboratory studies use.
-
product
Horse Surround Electric Fence Charger
HS-100
Parker McCrory Manufacturing Co.
Safe, effective, shock designed for animals that are sensitive to electric shock like horses, dogs and short haired animals. Approved by Leading Equestrians. Advanced Solid-State Circuitry Shocks through weeds & brush. Quick, and Easy Installation. Full 3 year warranty covers damage caused by lightning.
