-
Product
300KHz Precision LCR Meter
Model 4300R
-
Aplab Precision LCR Meter Model 4300R is a new generation of impedance test equipment with high accuracy, wide measurement range and six digits resolution. Being featured with test frequency up to 300kHz, test voltage of 5mV ~ 2V, built-in -5V ~ 5V DC bias and -10V~10V DC voltage source output, it can meet all requirements for measuring components and materials and provide guarantees for production line quality assurance, incoming inspection and laboratory precision measurements. The Handler, RS232C and GPIB interfaces as well as improved command system provided by the instrument make it easier to build the test system.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
Multifunction Switch/Measure Unit
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
PXI/PXIe Relay Driver Module, 64-Channel, 5V Relay Supply
42-411A-001
Relay Driver
The 40-411A-001 (PXI) and 42-411A-001 (PXIe) are 64-channel relay drivers and are part of a range of modules with 16, 32, 48 or 64 channels of low side current drive. To use the module, simply connect a positive voltage source to one side of the relay coil and the other side to an output channel. Each output is capable of sinking up to 1 A of continuous current.
-
Product
LINEAR AMPLIFIERS
-
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
Product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
Programmable Voltage Source
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Product
Three-Phase Relay Test Equipment
AK-30
-
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
Product
Low Power Potentiostats
-
Potentiostat Wenking MP 04T, max. current 400 mA, max. voltage 25 V, output power 10 W, reference electrode input 1012 Ohms, slew rate 10 V/ µs, 1 control input, floating current output, buffered potential output, control range ± 10 V external, internal control voltage source ±2 V, rise time constant (closed loop, ohmic load) 1 µs typ., dimensions 165 x 105 x 165 mm (w x h x d), weight 1.4 kg
-
Product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Arc Pro
-
Otii Arc Pro is an instrument that can precisely source voltage or current and simultaneously measure voltage and/or current. It computes power and energy and syncs with software output, enabling engineers and developers to easily see what drains the energy and optimize the battery life of their devices under test.
-
Product
PXI/PXIe 16-Channel Digital Output Module
40-412A-024
Digital Output Module
16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Light Dependant Resistance Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
L.D.R. Trainer comprises of light dependent resistor (LDR) fitted to the shaft, which moves inside the tube where lamp is fitted at the other end. Variable DC voltage source is provided to vary the light intensity. Digital indicator is supplied to measure the light intensity in terms of distance moved between LDR and light source.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
High Powered External IP Transmitter
PowerSting
-
The PowerSting is a series of external high power transmitters (5kW, 10kW, and 15kW) for the SuperSting R8/IP/SP and SuperSting R1/IP/SP. The PowerSting system is a fully programmable constant voltage//constant current source. The PowerSting system comes with an SGS generator and a wireless repeater box, and operates in both wired and wireless modes. The applications of the PowerSting-SuperSting system include vertical electrical sounding, 2D electrical imaging, 3D electrical imaging, 3D offset electrical imaging of a 2D survey line in both manual and automatic modes.
-
Product
Abrasion Test Setup for Coating of Hair Straightener
-
SCR ELEKTRONIKS have developed "4 Stations Abrasion Test Setup for Coating of Hair Straightener" for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
Product
High Voltage Power Source
PM2000
-
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
Product
Load Cell Power Supply
MODEL PSMR
-
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
Product
Digital kV Meter
VM-10, VM-20 , VM-30
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
High Voltage Meters measure AC and DC voltages of up to 30kV with high accuracy. The meter input impedance is as high as 1000 M ohm, making the meter suitable for measurement of voltages of high source impedance circuits. Meters are compact and light weight and can be conveniently used as a calibration meter.
-
Product
Medical Leakage Current Tester
2675Y
-
Shenzhen Chuangxin Instruments Co., Ltd.
The 2675Y Medical Leakage Current Tester Series Is The Test Equipment Used For Measuring Continuous Leakage Current And Patient Auxiliary Current Of Medical Electrical Equipment.It Designs And Products According To The GB9706.1_2020 (IEC60601-1:2012) .And The Test Circuit (MD)Input Impedance To Simulate The Body Impedance,It Accord With The Requirements Of GB9706.1-2020 (IEC60601-1:2012),The Test Current Can Run Up To 5A,And Provide Users With An Isolation Power Supply Which Adjustable Output Voltage For 0~250V Continuously Of The Basic Capacity Configuration For The 500VA And Provide Another 110% Voltage Source Of The Maximum Rated Voltage.It Can Satisfy The I,II, Various Types Of Equipment Test The Earth Leakage Current,Shell Leakage Current,Patient Leakage Current,Patient Auxiliary Leakage Current Under Normal Condition And The Single Fault.
-
Product
PXIe 64-Channel Digital Output Module
42-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Programmable DC Power Supply
SPD1000X Series
-
SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability, and real time wave display. This single output design is focused on delivering high performance and ease-of-use in a small package. The SPD1168 features a high precision programmable output capable of delivering up to 16 V/8 A,the SPD1305X features a high precision programmable output capable of delivering up to 30 V/5 A and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
High Voltage
-
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules. The flexible high voltage design platforms and responsive management structure enable us to offer an economically viable custom build. High voltage power supplies from ETPS are used in a variety of applications ranging from electron acceleration systems and mass spectrometers to magnetrons, x-ray and nuclear research.
-
Product
Power Sources
GF303
-
Beijing GFUVE Electronics Co.,Ltd.
GF303 Program-controlled three phase AC standard power source is a high precision three phase AC standard current source and AC standard voltage source.
-
Product
Solar Array Simulator
Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
Primary Current Injection Test Trolley
-
SCR ELEKTRONIKS have developed primary and secondary Current injection test trolley for Switchgear manufacturers for testing of ACB , MCB , MCCB. It is low Voltage high Current source with control circuitry, digital read out for test current and trip time measurement. We can select different links of CT range as per the required test Current.
-
Product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
-
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPHP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
CT / PT Analyzer
CTPTA-504
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.
-
Product
PCI Relay Driver Card, 64-Channel
50-411A-001
Relay Driver
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
Product
Withstand Voltage Tester
2672AM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
Product
Relay Testing Voltage Source
PTE-FCN
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
