-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
-
Product
RF Shielded Fixture
-
A semi-automatic, pneumatically operated fixture with a sliding pressure top provides a very short mechanical cycle-time. The unit is prepared for full, multi-station automatic operation using a centrally placed robot arm for UUT load/unload.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
-
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Functional Test Fixtures
-
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
-
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Test Fixture
N1295A
-
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Bottom Electrode SMD Test Fixture
16198A
-
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
Product
Fixturing Kit
10744A
-
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
Mini Pneumatic, Contact, Receiver, Push-in Fitting, for 6 mm OD Tubing
610131112
-
Primary mating contact 610132112.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
Product
ATE Self Test Fixtures
AL663
-
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules
610131108
-
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules.
-
Product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
-
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
Product
Test Fixture (SMD Components)
16034E
-
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
-
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
EBIRST 9-pin Male D-type Termination Fixture
93-003-103
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Parallel Electrode SMD Test Fixture
16192A
-
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
Pneumatic Contact, Receiver, Hose Barb, for 1/8" [3.2 mm] ID Tubing
610132105
-
Primary mating contact 610131106.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
SMD Array Type LCR Test Fixture
16034H
-
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
Spring Clip Fixture
16092A
-
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
EBIRST 104-pin D-type Verification Fixture
93-022-101
-
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Magnetic Material Test Fixture
16454A
-
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
Product
Pneumatic, Contact, Receiver (with valve), Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131107
-
Primary mating contact 610131106.Used in receiver module p/n 510104185, mates to contact p/n 610131106 and ITA modulep/n 510108160.
-
Product
Pneumatic Contact, ITA, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610132104
-
Primary mating contact 610131104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Bottom Electrode SMD Test Fixture
16197A
-
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Test Fixture Kits
-
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
