Test Leads
Cable hook-up between a test node and test instrument.
See Also: Flying Leads, Multimeters
-
Product
Test Leads
AL-34WB 10A
-
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
-
Product
Extendible Test Leads
-
The Extendable Tip Probe permits testing in those hard to reach areas. The tips are fully insulated with durable Kynar. This prevents accidental shorting of adjacent components. The tip is stainless steel and is very sharp, allowing for penetration of conformal coatings. The rubber lead is 18 gauge, 48" long.
-
Product
Fuse Lead Automotive DMM Test Leads
134
-
*ATC Fuse Holder In-Line *Provides extra overload protection *Can prevent your DMM’s internal fuse from blowing *For use with any Digital Multimeter
-
Product
Interconnect Test Leads
142-1
-
This 64 inch pair of test leads connects with many different testing accessories and probes. Especially those found in typical test lead kits and assortments. The ends terminate in universal size 4mm banana plugs.
-
Product
LOADpro Dynamic Test Leads
180
-
*LOADpro Test Leads load the circuit to see if current can flow. *By loading the circuit, LOADpro makes a voltage drop test “on the fly”. *Just press the switch – the test results can not lie. *Use LOADpro w/your DMM and follow our test method - you will find wiring faults quicker. *LOADpro Test Leads feature SteadyPin Probe Tips, which allows the probe to sit firmly on a male ECM or connector pin. *LOADpro are OEM approved – finds corroded circuits fast!
-
Product
Test Leads
-
Test leads for digital multi-meters (DMM), tone generators, butt sets, oscilloscopes, and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
Coaxial Cable
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
Product
Test Leads
-
designed for electrical and electronics testing in today’s industrial environment.
-
Product
Test Leads and Probes
-
Test leads and probes are an intergral part of a complete measurement system and extend the capabilities of your digital multimeter.
-
-
Product
48" Stacking Banana Plug Test Leads
146-P
-
These test leads feature stacking banana plug jacks, with extended 48" length. These are great for establishing connections to diagnostic test points, while allowing the connection to be tapped with other instruments...2 way connections. These feature high flexibility wire and standard 4mm size banana jacks. You will receive one red test lead and one black test lead. These test leads are compatible with Electronic Specialties 146 and 147 test lead kits.
-
Product
Probes & Test Leads
-
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 1.5m
N1425A
Coaxial Cable
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
Product
Test Leads With Screw-Off Alligator Clips
629
-
*Alligator clips screw off / on for more secure connection *Test leads 48” length *1000 Volts max - CATIII *Maximum 10 Amps
-
Product
Multimeter Electronic Test Leads Kit
-
VERSATILE KIT includes 2 alligator clips with removable insulation, 2 extended range plunger mini-hooks with pass-through banana plugs, 2 heavy duty test probes, 2 42” lead extensionsUNIVERSALLY COMPATIBLE with either 0.16” banana plugs or shrouded banana plugs on all ends
-
Product
48V LOADpro Dynamic Test Leads
185
-
This new version of LOADpro is capable of loading circuits as high as 48 volts. 185 can be deployed on electrical systems ranging from 12 volts up to 48 volts. Applications include automotive, heavy-duty, marine, off-road, agriculture and electric vehicles. 48V applications include electric equipment, lift trucks, scissor lifts, golf carts and other battery powered vehicles.
-
Product
Test Leads
-
An IT professional who oversees the process of testing software before moving it to production.
-
Product
Test Leads
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
Product
Test Leads
8000 Series
-
The "SOFTIE" by Probe Master lets you say "goodbye" to hand fatigue and finger calluses. A soft probe that bends 90 degrees or more. A probe that conforms to the shape of your hand. This soft flexible probe bends gently to reduce wear and breakage of the lead. Many combinations are possible with the "screw on" accessories shown above. The 48" long, 18GA. test leads, are made of top quality silicone.
-
-
Product
Fused Test Probes with Silicone Test Leads
AL-56FL
-
Standard Electric Works Co., Ltd
Fused Test Probes with Silicone Test Leads
-
Product
Kelvin Clip Test Leads
-
Specialized four-terminal connectors that eliminate lead resistance and contact errors during precise low-resistance or impedance measurements.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Variable Power Supply
VS-10a
-
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
Product
On-site Support
-
Aerodyn provide a complete field test service, offering on-site support at demanding and often remote test sites. We instrument test articles, route lead wires, configure data acquisition systems, record data, reduce data, and write test reports. We conduct tests on aircraft, in test cells, at power stations, aboard ships, and at manufacturing facilities.
-
Product
Mag Lead w/Alligator Clips
138
-
*54" Test Lead Set *Mag Lead features a magnetic disconnect. *You can "stick" to any metallic ground or test point. *Time saving product - can substitute for alligator clips at metallic test points. *Now, when you need alligator clips, you've got them! *Fits almost all DMM's and hand held scopes. *Get the Mag Lead, it stays put and won't fall off!
-
Product
Battery Tester
BT168
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
*Test of all AAA,AA,C,D, lithium and 9V batteriesl*No test leads needed *Easy-to-read color scale *Self powered-no need of battery*Small and light weight,ideal for home use.*Measuring range1.5V:Button,AAA,AA,C,D 9V:al popular type
-
Product
Alligator Clips
U1162A
Accessory Kit
Pair these insulated alligator clips with Keysight standard test leads
