Bare board Fixtures
accurately position and retain unloaded PCBs.
See Also: Bare Board Testers, Board Test Fixtures, Bare Board
-
product
Manual Fixture Kit
230353 – CMK-04
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
-
product
Drop-In In-Circuit Test Fixtures
The Chameleon
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
product
Automatic Fixture Removal
S93007B
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
product
Exchangeable Test Fixture
MA 2111/D/H/S-5
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
-
product
Edge Connector Fixture
EDGE
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
product
Overhead Board
OVH-380-2
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
-
product
Breakout Boards
"Breaks out" these pins onto a printed circuit board that has its own pins that are spaced perfectly for a solderless breadboard, giving you easy access to use the integrated circuit.
-
product
GPGPU Board
NVP2009
As part of our NVIDIA Pascal™ based chip-down series of GPU XMC products the NVP2009 is ideal for GPGPU applications such as C5ISR, situational awareness, signal intelligence (SIGINT), as well as machine learning and autonomy.
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
product
Custom PCB Test Fixtures
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
product
Turn-Key Functional / Mechanical Fixture
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
product
Custom Test Fixtures
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
product
Universal Test Fixture
CAM/GATE
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
product
Burn-In Test Fixtures
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
product
NON-CONTACT TEST COMPATIBLE Ultra High Speed Bare Board Tester System(ALL-IN-ONE UNIT)
SX-750SUPERⅣC
All-in-one Compact Size TesterAll-in-One type Tester, with built-in PC in the Tester main unitImproved operability with a 10.4" Touch PanelAll the operation screens are optimized for touch-pannel operation.
-
product
Wireless Functional Test Fixtures
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
product
Sampling Boards
MSXB 028
Simultaneous Sampling Boards are used in multichannel spectral analysis and other applications that require simultaneous acquisition of several channels. The MSXB 028 usually is used for applications that require interchannel phase measurements such as applications that perform transfer function computations. This board eliminates phase error introduced by sequential sampling.
-
product
Board Drivers
9450-DRV
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
product
Press - Down Fixture Kits
*Supports most press - down testers *High - Quality *Precise & Reliabe
-
product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
product
Embedded Boards
Elma offers embedded computing board level products, including single board computers, mass storage, Ethernet and PCIe switches, FPGAs and custom I/O solutions. Our focus is to provide proven technology based on standard architectures like VME, VPX, CPCI, ATCA, and COM-Express as well as other standard and custom small form factors. We partner with leading board manufacturers.
-
product
Carrier Boards
ROM-DB7501
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
product
Functional Test Fixtures
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
product
OpenVPX Boards
Configuring OpenVPX systems can be tricky. Utilize Pixus' expertise in selecting the right VPX modules for your application. With our key partnership, Pixus can help you find the right boards at the right price. For simplicity, you can order your full OpenVPX system and boards through Pixus or we will refer you to the best fit for your application. Our flexible approach leaves the choice to you, and helps ensure you are getting the best performance and value required for your system.
-
product
OEM Boards
4865B
* Embed the GPIB-to-Ethernet Interface in your instrument.* Available in three different connector configurations.* To have the GPIB Connector protruding thru the rear panel. Order P/N 115907* To mount the board anywhere inside the chassis and use an inexpensive flat-ribbon cable to a GPIB connector on the rear panel. Order P/N 115895. Order the 114439 Cable separately.* Mount inside the chassis and use a GPIB extension cable to a GPIB connector on the rear panel. Order P/N 115897.* Runs on instrument's DC power.* Same specifications and performance as the 4865B Minibox™ version.
-
product
Ethernet Test Fixtures & Software
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
product
Audio Board
MS 1813
*Two Audio Output Channels (Playback)*Two Audio Input Channels (Recording)*High performance Stereo Audio Codec*PCI Bus Interface
-
product
Test Fixturing Solutions
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
