RF Switching
The opening and closing of RF connections.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-004
This multiplexer has low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
product
Handheld RF Power Meter
V3500A
The V3500A Handheld RF Power Meter is a compact, handheld instrument that makes accurate RF power measurements in both field and manufacturing applications. With an absolute accuracy as good as 0.21dB, a wide frequency range of 10MHz to 6GHz, and a measurement range of -63dBm to +20dBm, the V3500A is suitable for a wide variety of RF measurement applications. Its built-in power sensor eliminates the need for users to carry both an instrument and a separate sensor module. Truly portable, the V3500A fits easily into your hand or a toolkit. An optional belt loop holster or carrying case with shoulder strap is also available. To optimize flexibility, it is capable of drawing operating power from batteries, an AC-DC converter module, or a computer via USB interface.
-
product
PCI RF Switch Cards
These 8x9 RF Switch Cards are suitable for switching frequencies up to 500MHz. Available in either 50 or 75 versions with SMB coaxial connectors. These switch cards are intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic isolation switches are located on all coaxial connections, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
LXI Dual Bank, 12:1 MUX 75 Ohm 1GHz F-type
60-722-002
Our 60-722 High Isolation RF Multiplexer is suitable for switching 75 ohm signals up to 1GHz. With the choice of single or dual multiplexer banks each with 12 channels, it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted F-type connectors.
-
product
RF Signal Generator
SMB100B
The new R&S®SMB100B RF signal generator is all about performance and versatility in a small footprint. Outstanding spectral purity and very high output power combined with comprehensive functionality and very simple operation are some of the impressive features of the R&S®SMB100B. It offers a frequency range from 8 kHz to 1 GHz, 3 GHz or 6 GHz.
-
product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
product
75Ω High Isolation LXI RF Multiplexer
Pickering's LXI high isolation RF multiplexers are suitable for switching 75Ω signals up to 1GHz - ideal for constructing complex microwave switching systems for many applications. These matrices are supported by a comprehensive range of cable and connector accessories and come with a standard 3 year warranty.
-
product
RF Signal Generators
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
-
product
General Purpose PXI Relay Switch Modules
PXI relay switch modules offer reliable switching in a variety of configurations. They consist of multiple independent single-pole single-throw (SPST), single-pole double throw (SPDT), double-pole single-throw (DPST) and double-pole double-throw (DPDT) relays. Our PXI relay switch modules come in a variety of relay types including reed relays, electromechanical relays (EMR) and solid state relays—offering you the optimum switching performance for your application.
-
product
Multi-Purpose Relay/Multiplexer/Matrix/Switch Card
1260-39
The Astronics 1260-39 is a high-density, multi-purpose, switch module. The combination of relay, multiplexer, and matrix switch functions, in addition to multiple user-defined configurations, offers a single-module solution for low-to-medium switch count applications. The 1x2 and 1x4 multiplexers can be externally configured to provide up to six 1x4s or two 1x12s.
-
product
PXI Transfer Switch Module
PXI Transfer Switch Modules offer fast insertion times and low insertion loss to switch loads at RF frequencies. The modules also have 50 impedance that helps minimize reflections of the RF signal and protect your instruments. You can program the PXI Transfer Switch Module using the NI-SWITCH instrument driver.
-
product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
Coaxial Plug-in Switch Card
1260-152/172
The Astronics 1260-152/172 is a high- frequency coaxial switch card for use in either the Adapt-a-Switch® 1260-100, VXI carrier, or the 1256, GPIB/RS-232 Switching Mainframe.
-
product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected)
150579-01
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected) - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
40-782B-551-E
The 40-782B-551-E (PXI) and 42-782B-551-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
product
Modular VXI Switch Card Carrier
1260-100
The 1260-100 Switch Carrier accommodates up to six plug-in switch cards, providing optimum switching solutions while reducing the ATE size requirements.
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-FK230-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Standard 2.90 (82.20) - 5.40 (153.00) Switch Probe
TSP157-F200-1
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 157Test Center (mm): 3.99Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 984Overall Length (mm): 25.00Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-J100-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI 8 Trib Daisy Chain Switch 120Ohm Balance
40-795-001
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
product
PXI Single 8 Channel Switch Simulator
40-485-021
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
PXI Dual Transfer Switch 40GHz 50Ω SMA-2.9
40-782-542
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
product
PXI Solid State Switch Module, 6xSPST, 30 A, Hardware Interlock
40-183B-011-HI
The 40-183B-011-HI has 6 high current SPST switches with hardware interlock in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode
40-860A-332-HI
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Standard 4.10 (116.00) - 6.50 (184.00) Switch Probe
MSP-3C
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 140Full Travel (mm): 3.56Recommended Travel (mil): 85Recommended Travel (mm): 2.16Mechanical Life (no of cyles): 100,000Overall Length (mil): 2,140Overall Length (mm): 54.40Switch Point (mil): 30Switch Point (mm): 0.76
-
product
PXI Dual 8 Channel Switch Simulator
40-485-121
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
