NDT
examination free of damage to UUT. Also known as: Non-Destructive Testing
See Also: Non-destructive Test, Testing
-
Product
Laser Shearography NDT Sensor for Quality Control, Academic Research, or NDT Training
FlawScout
-
The FlawScout is a laser shearography non-destructive testing (NDT) sensor designed to be used for (post-production) quality control, academic research, or NDT training. The sensor can be configured with thermal or vacuum (partial) excitation systems depending on the application. The FlawScout incorporates the very latest in phase-shifting technology delivering accurate and reliable measurement results through clear and sharp imaging with sub-micrometer displacement resolution.
-
Product
A-/B-Scan Thickness Gauge For NDT
SONOWALL® 70
-
SONOWALL 70 is the first thickness gauge in the market with intelligent probe identification. The extended probe management allows probe-specific information such as DAC-curves, delay lines, and serial numbers to be saved directly in the ultrasonic probe. In addition to various thickness applications, the device can be upgraded to a full-function flaw detector.
-
Product
X-ray Non-Destructive Testing (NDT) System
DynamIx HR / Series 5
-
High precision 12-bit 50µm reading allows inspection of minute image details. Wide dynamic range resulting in wide allowance of X-ray exposure value.
-
Product
Integrated NDT Inspection Device
FlawHunter
-
The FlawHunter is an integrated NDT inspection device, equipped with an advanced, high-resolution Laser Shearography sensor with a vacuum (partial) excitation system. It is ergonomic & easy-to-use and is equipped with a workflow-oriented, GUI-display and left/right-hand button control. Regardless of the application, the FlawHunter provides reliable and resolute measurement results for in-field (service) NDT and quality control (post-production) operations.It can be used on any material & surface provided a stable vacuum can be generated within the vacuum seal (viewable inspection area).
-
Product
Ultrasonic NDT Transducers
-
United Western Technologies Corp
The Quick Change Transducer (QCT) series of transducers that makes changing wedge angle and transducer frequency rapid and easy, saving both time and money. The QCT connects straight into the wedges allowing for many combinations all within one kit. All QC Transducers are fitted with top mounted microdot connectors allowing for seamless transition from one transducer to the next. The stainless steel transducer housing will resist even the harshest working conditions. The emphasis of the QCT is general purpose with a balance of power and resolution, a High resolution version is available upon request.The Quick Change Wedge (QCW) is simple to setup and operate, utilizing incorporated noise dampening material on the wedge. Offered in steel, aluminum and titanium refracted angle. Custom contours, radii and wear pins available upon request.The QCT and QCW series are extremely versatile and can be used in many different applications and in a wide variety of industries and environments.
-
Product
Non-Destructive Testing (NDT)
-
Marposs complements its geometric measurement solutions with solutions for non-destructive testing using eddy current technology.The testing options can be divided in three large groups:Material integrity test, to check for the presence of defects (cracks, porosity, blow holes, inclusions) on the surface and in the layer just below the surface.Material properties test, to check if the thermal cycles (hardening, hardening and tempering, annealing, stress relieving, etc.) have been performed correctly. Material identification checks are done to sort parts with the same geometry but made with different materials.Thread inspection to check if the treading has been carried out and its quality.In addition to the non-destructive checks performed with the eddy currents, we have developed a durometer for the conventional measurement of surface hardness, according to the Rockwell scale (HRC or HRA); which uses a diamond penetrator to measure the hardness of the sample being tested.
-
Product
NDT And Ultrasonic Testing
-
ToronTech offers a wide range of Non-destructive testing (NDT) techniques & machines to evaluate the properties of a material, component or system without causing damage.
-
Product
Magnetic Particle Inspection
NDT
-
DCM Tech offers a comprehensive selection of Magnetic Particle Inspection machines for non-destructive testing (NDT). Easily and quickly detect internal and subsurface damage on critical parts. Contact DCM to speak to your regional Technical Specialist about adding an MPI to your shop.
-
Product
NDT Testing Instruments
-
Portable vibration calibrator, digital Brinell hardness tester, digital low load Vickers hardness tester, Rockwell hardness meter
-
Product
High Quality UCI - And Leeb-measuring Technology
SONODUR Product Family
-
Foerster Instruments, Incorporated
The non-destructive UCI test method (Ultrasonic Contact Impedance) as well as the Leeb test method enable fast and mobile measurement as a supplement to the classical hardness test. Due to the compact measuring probes and sensors of the SONO series, the devices can also be used in difficult test positions and with complex component geometries. Fields of application are e.g. incoming goods inspection, mix-up testing, production control, quality assurance, weld seam testing, cut edge testing, maintenance on installed components as well as the replacement of dynamic hardness testers for small material thicknesses (below 50 mm, e.g. boilers, tubes).
-
Product
Ultrasonic Testing
-
Xiamen IDEA Electronic Technology Co., Ltd.
Is a family of non-destructive testing techniques based on the propagation of ultrasonic waves in the object or material tested.
-
Product
Production Spin Testing & Balancing Services
-
Test Devices provides production spin testing and balancing services of production parts for customers with a repetitive need and who demand schedule predictability along with a quick turn-around time. Whether proof testing critical rotating components before shipment, pre-spinning to achieve required rotational growth prior to finish machining or simplifying the supply chain by consolidating pre-spin with rough machining and/or NDT inspection, Test Devices offers a full range of spin testing solutions.
-
Product
Concrete Strength Testers
-
This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.
-
Product
Concrete Hardness Tester
W-M-250
-
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
Product
Cable Diagnostic Tools
-
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
Product
Ultraschallmikroskop And Scanning Acoustic Microscopes
-
Microtronic Microelectronic Vertriebs GmbH
mage quality. Speed. Uptime. They’re all crucial. Getting all three at the same time in a nondestructive testing (NDT) solution for package inspection is the challenge. It takes continuous innovation, advancing the state of the art to keep pace with the semiconductor industry’s own exponential progress.Sonix has been the innovation leader since 1986. Today, the ECHO line of scanning acoustic microscopes sets the standard for package inspection speed and image quality, to help you keep pace with new packaging materials and difficult form factors. The ECHO platform will remain at the forefront as we continue to add features and enhance performance for years to come.
-
Product
Acoustic Emission Transducer
GT200
-
Acoustic emission transducer is a key element of non-destructive acoustic emission testing. Transducers GT 200 are used for technical diagnostics by means of passive ultrasound.
-
Product
Eddy Current Testing
-
PRÜFTECHNIK Condition Monitoring GmbH
Nondestructive testing systems from Prüftechnik ensure that manufacturers of semi-finished products and their customers obtain the best possible quality. Our eddy current testing systems and sensors provide quality assurance and process control and help you guarantee the security of your investment.
-
Product
Pinhole Detector
NOVOTEST ED-3D
-
NOVOTEST ED-3D Pinhole Detector was designed for rapid non-destructive testing of the continuity of coating (e.g. porosity of film) with thickness up to 500mkm according to ASTM G62-A.Pinhole Detector is designed for testing the porosity of partially painted places and other discontinuities of protective dielectric coatings on metal products by putting low voltage through a sponge which is soaked in a liquid electrolyte with high penetrating properties.
-
Product
Leeb Hardness Tester
-
Shenzhen Linshang Technology Co., Ltd.
Based on the principle of Leeb hardness measurement, the Leeb Hardness Tester, otherwise called as Leeb Rebound Hardness Tester, is considered as one of the most commonly used tools to test the hardness of the metal. It is a type of non-destructive testing tool used to inspect large sized workpieces weighing above 5 kg. Besides the hardness, it also measures the strength of materials.
-
Product
Eddy Current Scanners
-
United Western Technologies Corp
a non-destructive testing (NDT) device that uses electromagnetic induction to detect surface and near-surface flaws in conductive materials.
-
Product
Beam Directional Power Supply Battery 40 to 120 kV
CP120B
-
This ultra-light, compact and battery operated constant potential portable X-Ray generator is the perfect tool for specific NDT applications that require repetitive short exposures. Its versatility also makes it the ideal piece of equipment for security applications. In fact, in combination with the FLATSCAN15, the FLATSCAN30 and other digital X-Ray detectors, the CP120B will – thanks to its small focal spot and constant potential X-Ray output – enhance image quality and definitely contribute to a reduced exposure time.
-
Product
Humidity and Temperature
Thermal Cameras
-
Non-destructive testing / Humidity and Temperature
-
Product
Magnet Permeability Meter
List-Magnetik FerroPro
-
The List-Magnetik FerroPro compact permeability measuring device can determine the relative magnetic permeability (µr) of materials and structural parts within the range of 1,000 to 5,000. It is ideal for testing materials, especially ferromagnetic materials, to provide precise NDT (non-destructive testing) data.
-
Product
Photostability and NDT Radiometer
R203
-
Most drugs and pharmaceutical compounds are required to be tested for their photostability under prolonged exposure to visible and ultra violet light.Additionally, when using fluorescing dyes in crack detection the ambient visible light levels and the intensity of the ultra violet source have to be controlled.
-
Product
Non-Destructive Test Resonant Inspection System
RAM-AUTO
-
Resonant Acoustic Method is designed to help deliver fully inspected parts, economically and on time. Every component has a unique resonant signature or pattern that reflects its composition.
-
Product
Inductive Heat Flux Thermography
DEFECTOVISION IR Product Family
-
Foerster Instruments, Incorporated
The DEFECTOVISION IR system is an addition to FOERSTER's core competence, the non-destructive testing of semi-finished metal products. All around the world, more than 6.5 million tons of steel have been tested safely and efficiently by now with our latest technology.
-
Product
Time Domain Reflectometer (TDR) Card
PCI-3127
-
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
Product
Steel Structure Analyzer
NOVOTEST KRC-M2 (Coercive Force Meter)
-
Steel Structure Analyzer NOVOTEST KRC-M2 is designed for measuring coercive force of metal products in accordance with IEC 60404-7 and is used for non-destructive testing of chemical-thermal, thermal and thermomechanical treatments, evaluation of mechanical properties and residual stresses.
-
Product
Air Tightness Detector
FQ
-
Fuzhou Fuguang Electronics Co., Ltd.
FQ series air tightness tester is the latest high-precision non-destructive testing equipment developed by Fuguang Electronics. The equipment mainly uses compressed air as the medium to apply a certain pressure to the inner cavity or surface of the product to be tested, and then uses a high-sensitivity sensor to detect changes in pressure to determine the tightness of the product to be tested.
