Phase Angle
Measure electrical phase angles or visualize stero sound.
See Also: Phase, Phasing, Phase Standards, Phase Meters, 3 Phase, Phase Angle Meters, Phase Angle Voltmeters, Phasors
-
Product
Three Phase Voltage Disturbance Recorder
PQR 2020
-
The PQR 2020 is a Three Phase Voltage disturbance detector and recorder. This device is designed to be connected to a single phase 120V or 240V AC line or a Three Phase 208/240/480 Volt AC line and will monitor these lines for voltage disturbances.
-
Product
Phase Verification Bridges
5002
-
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
Product
Cable Identification System & Cable Phasing System
Impulse Phaser
-
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
-
Product
Phase Detectors
-
Holzworth Instrumentation, Inc.
These components are targeted for use in phase noise measurement systems and ultra low phase noise phase lock loop designs.
-
Product
28 Days Test Bench (Single Phase & Three Phase)
-
The SCR Elektroniks 3 station MCB 28 Days and Temperature Rise Test Bench is economically designed to verify the 28 Days Test (21 hr ON, 3 hr OFF Test) as per clause 9.9 of IEC 60898-1 and Temperature Rise of the parts of a Circuit Breaker specified in Table 6 of clause 8.4.1 measured under the conditions specified in clause 9.8.2 of IEC 60898-1.
-
Product
PCB Bracket Kit, SIM Module, Receiver/ITA, for PCB Mounting (Right Angle)
510109592
-
Required for mounting SIM module to PCB. See Infinity Connector User Manual. Brackets already included in pre-loaded SIM modules p/n 510171102 and 510170102.
-
Product
Tool, Insertion, Right Angle, VTAC
910112132
-
Used to install VTAC Right Angle inserts (p/n 610151104) onto a PCB.
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
Signal, Insert Bundle, Receiver, QuadraPaddle, SIM, Right Angle and Pass-Thru
510180107
-
Signal, Insert Bundle, Receiver, QuadraPaddle, SIM, Right Angle and Pass-Thru.
-
Product
Phase Shifters & Bi-Phase Modulators
-
PMI offers the highest quality phase shifters and bi-phase modulators for industrial and military applications in the frequency range of a few MHz to 40 GHz. If you do not see exactly what you need, please e-mail your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
Product
Flex Power Right Angle Non Shut-Off Pulse Tools
-
The non shut-off right angle pulse tools are ideal selection when the operator needs to control the fastening process. It offers access for hard-to-reach fasteners in tight spaces. The drive on a right-angle tool is mounted at a 90-degree angle to the tool body. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
Hi-Q W-Band Ultra Low Phase Noise Analyzer
OE8000W
-
HI-Q® W-Band phase noise test system utilizesmicrowave photonics techniques for automatedmeasurement of ultra-low phase noise W-bandoscillators.
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 96 Position, w/ Right Angle Contacts
510104135
-
Primary mating module 510108125. (May mate with other ITA modules, as well.)
-
Product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Phase Masks
-
Phase masks are the production tool used to write gratings in fibers and waveguides. Ibsen Phase masks incorporate unbeatable, interferometric (holographic) patterning technology into a production friendly Phase mask.
-
Product
Wide Angle Scale Instrument
LS-110 LS-80 Var
-
Standard Electric Works Co., Ltd
● Easy to read long-scale and pointer-indications can easily be read from a distance.● Full Scale Deflection : 250°● Accuracy : Class 1.5● Scale Length : LS-110 : 183mm LS-80 : 140mm● Case and Composition : Acrylic resin cover, plastic with UL body and terminal, Four studs mounting. LS-110 case : plastic body option 1 : plastic body with metal case, no UL option 2 : metal case, no UL exception : W, VAR, PF (3P4W)● Color : White scale plate, black terminal plate, black meter body.● Pointer : Sword-type in black color.● TAUT BAND / Pivot & Jewel for LS-110.
-
Product
Digital Controlled Phase Shifters To 4 GHz
-
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
Product
Non-Contact Type Phase Sequence Indicator
890 PR
-
Standard Electric Works Co., Ltd
● The 890 PR is a Non-Contact phase detector with flashing LEDs and a beeping buzzer to show the detection of AC 3-phase sequence.● Two functions in one unit : open phase and phase sequence detection.● Convenient brightness switch to make the indication visible in dim areas or sunlight.● Back cover magnets which attach the instrument to the AC distribution panel offer easy measurement. ● 3-Phase AC 75 to 1000V is fitted for detection.● Conductor size: 1~35mm● Detect frequency range is from 45 to 65Hz.
-
-
Product
3 Phase Meter - Anti-Clockwise
135012
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
Close Link Three Phase Energy Meter Test Bench
SY8320E
-
Hong Kong Songyang Industrial Ltd.
Close-link and ordinary calibration both can be used, ordinary calibration can be used to test single/three phase active and reactive energy meter (up to 0.5 class),close-link calibration can be used to test single/three phase active and reactive energy meter (up to 1 class)
-
Product
Single Phase Relay Tester
PTE-50-CE Pro
-
This electronic, independent source can be adjusted in amplitude, frequency, and phase angle. It comes installed as standard with the ‘Pro’ versions of the PTE sets, but it can also be purchased separately and mounted by the user inside the unit’s lid in a few minutes.
-
Product
Phase Sequence Indicators (Contact Type)
855 PRB
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
Product
Horizontal Angle Encoder
TRUANGLE
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*LCD Display*Accuracy ± 0,05°*RS 232/Serial interface*IP protection IP54
-
Product
Single Phase Relay Testing
-
Megger’s single phase relay test sets are essential items in the relay engineer’s toolbox. Lightweight, rugged with high compliance voltage and test current. Ideal for testing distribution networks, industrial relays, distance relays in rail power networks and many other applications.
-
Product
30" Support Angles
SA-30
-
30" support angles provide 3” of horizontal surface along each side of vertical cabinet for supporting instruments.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A800DI
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Product
3 Phase Relay Test Set
-
This is a portable Relay Testing Set suitable for testing different types like over current, earth leakage relays, circuit breakers of 1A – 50A rating etc. All the components are assembled and enclosed with a portable air cooled M.S.cabinet.
-
Product
100-Pin Micro-D Connector, Right Angle PCB Mount, Female, 2-56 UNC Screwlocks
C100SFX-1PR-5A
-
Female right angle PCB mount 100-pin Micro-D connector allows a user to create their own PCB based termination solution. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
