Thermal
The radiation of heat.
See Also: Energy, Chemical, Electrical, Nuclear, Electromagnetic, Thermal Shock, Thermal Test, Infrared
-
product
High Temperature Source
The Veeco High Temperature Source provides thermal evaporation of charge materials at temperatures up to 2000°C. This compact MBE source operates efficiently to achieve high temperatures without excessive thermal load on the system. Low power requirements also enhance the lifetime of the heater filaments.
-
product
Liquid Thermal Shock Baths
TSB Series
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
product
Constant Temperature Humidity Battery Test Chamber
Guangdong Test EQ Equipment co., Ltd.
- Battery-Specific Thermal Management: Dual-compressor cascade cooling (-40°C stability) and ceramic heaters for rapid high-temperature recovery.- Precision Electrochemical Control: Integrated battery cyclers with CAN/Modbus protocols, supporting SOP (State of Power), SOH (State of Health), and DCR (Direct Current Resistance) monitoring.- Safety-Centric Design-meet Hazard Level: Chambers are designed with Fire-resistant stainless steel interior, fire suppression,nitrogen purge system, and emergency power cutoff for thermal runaway prevention .- Data Acquisition & AI Analytics: Real-time logging of voltage, current, temperature, and pressure via LabVIEW/Python APIs. AI-driven anomaly detection reduces test cycles by 30%.- Energy Efficiency and Energy Storage: Heat recovery during discharge cycles cuts energy use by 25% (ISO 50001 compliant).
-
product
Dynamic Micro Ohm Meter
PRIME 600
It is the only micro ohm meter in the market that integrates both the contact resistance and the dynamic resistance measurement (DRM) for cost-efficient condition evaluation of contacts in SF6 and vacuum type circuit breakers; PRIME is a high current micro-ohmmeter that provides true pure DC with smart control up to 600 A, a wide measurement range with high power, dual ground testing process, thermal printer, touch display, pre-defined test modes and automatic reporting.
-
product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
product
Thermal Conductivity Gas Analyzer
CI2000-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
Determining gas concentrations by measuring the thermal conductivity of the gas, CI2000-RQD analyzer uses advanced thermal conductivity sensor with single chip technology. It adopts platinum thread as sense organ to make up Imbalance Bridge, which output signal has a relationship with tested gas volume. And the single chip will magnify, sieve wavelength, modify linearly and criteria the signal by electric procedure.
-
product
AC Current Shunts
AC Current Shunts feature low uncertainty (high accuracy), low temperature coefficients and excellent stability. These shunts are purely resistive with extremely small values of reactance. The 7340 shunts may be used over a wide frequency range from DC to 100 kHz and are optimized for use with thermal converters.
-
product
Ultra-Agile Frequency Synthesizer
Corech’s Ultra-Agile Frequency Synthesizer packs impressive low phase noise of -100dBc/Hz@10kHz@20GHz, low spurious of -65dBc, high temperature and corrosion resistance, long operating life, temperature uniformity, and good thermal conductivity. These outstanding performance make it suitable for high-reliability and environmentally stressful applications including communication systems, test and measurement equipment, radar systems etc.
-
product
3.5" Embedded SBC With Intel® Atom® Processor E3845/E3827, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA840
The CAPA840, a fanless 3.5-inch embedded single board computer, is based on the latest generation of Intel® Atom® processor E3845 or E3827 featuring 1.91/1.75GHz clock speed. Two DDR3L SO-DIMM slots support system memory up to 8 GB. Moreover, the fanless embedded board delivers better level of processing and graphics performance than previous generation Intel® Atom™ SBCs, while consuming less power. In addition to rich onboard I/Os, the CAPA840 adopts an ZIO connector on the rear-side that integrates PCIe x1, USB, LPC and SMbus expansion. With excellent thermal design, the 3.5” embedded board is able to run fanless and works smooth between -20°C to 70°C environments.
-
product
Ball Pressure Tester
4710
The ball pressure tester is used to test the thermal properties of insulating materials. The test sample is placed in an oven and a steel ball is pressed against the surface. The impression of the steel ball is measured to see if it meets the requirements.
-
product
Pocket-Sized Thermal Vision Monocular
FLIR Scout TK
The FLIR Scout TK is a pocket-sized thermal vision monocular for exploring the outdoors at night and in lowlight conditions. Scout TK reveals your surroundings and helps you see people, objects and animals over 100 yards (90 m) away. Simple to use, with still image and video recording, Scout TK is the perfect companion, whether in the back country or your own backyard.
-
product
Ultra-compact, Uncooled Thermal Imaging Core
Dione 1280 CAM Series
The Dione 1280 CAM series is based on the Dione 1280 OEM thermal imaging core with 1280 x 1024 pixels and 12 μm pixel pitch. The NETD is less than 40 mK (available upon request) or 50 mK. The maximum frame rate is 60 Hz.The camera cores are optimized for low SWaP (Size, Weight and Power). The Dione 1280 CAM is both lightweight and small. It utilizes Xenics image enhancement for advanced image processing while keeping power consumption low.Dione 1280 CAM is a LWIR uncooled thermal imaging SWAP module with housing supporting M34/M45 lens (optional).The ultra-compact Dione 1280 CAM series find application in safety and security systems, as well as in industrial thermal imaging systems.
-
product
Compact Short Range HD Multi-spectral Surveillance System
TacFLIR® 230
The TacFLIR® 230 provides maximum sensor range performance including a high-resolution color zoom TV camera with low light capability, a powerful 640x480 cooled MWIR thermal camera with 18x total magnification, and optional laser pointer and rangefinder. At 41 pounds and with a nine-inch diameter, the TacFLIR 230 provides the ability to deploy on any platform including UGVs
-
product
Passive Imaging & Radiometers
PMMW
A low attenuation atmospheric window from 80-110 GHz (W Band) makes this band an ideal candidate for PMMW systems. Passive imagers operate by detecting naturally emitted thermal (black body) radiation from an object. Products available up to 345 GHz.
-
product
Limits and Scanners
Watlow Electric Manufacturing Company
Various configurations offer user-selectable or fixed-configuration sensor options including thermocouple, process, RTD and thermal switch inputs as well as user-settable or fixed limit values. Models with displays have user-selectable temperature units. Other features include sensor break protection, industry standard I/O options and UL® and CSA approval. EZ-ZONE models are RoHS compliant. Limits have FM approval for performance in safety limit applications. Watlow limits are designed and manufactured to withstand harsh industrial environments and come with a three-year warranty.
-
product
Transmission Meters
Shenzhen Linshang Technology Co., Ltd.
As a leading window film transmission meter (window tint meter) manufacturer, Linshang Technology provides a variety of window film meters to measure transmission rate, rejection rate, SHGC for materials such as automotive film, thermal insulation film, architectural film, thermal insulation glass, etc. There are mainly portable solar film transmission meters LS160 series, LS162 series, LS163 series, desktop demonstration window tint meters LS101, LS180, LS181, L182, split transmission meters LS110A, LS110H. Whether you want to measure UV or IR rejection (940nm, 1400nm) or visible light transmittance, you can find a suitable window film meter here.
-
product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB208
The FAB208 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB208 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110. We have two enclosures, the AX60551 and AX60552, to house the backplane.
-
product
Fused Imagers
Fused imagers (fusion multi-sensor imaging systems) offer increased surveillance capabilities due to fusion of classical thermal image with classical visible image. The fusion systems are typically built by combining optically images from thermal imager and classical night vision device, or by combining digitally images from thermal imager and digital night vision devices (or electronic VIS-NIR camera).
-
product
High Performance TIC 320x240 (3 Button)
FLIR K55
With a FLIR K55 TIC in hand, you can attack fires more strategically, maneuver through smoke more easily, and save lives. The K55 displays crisp thermal images on a bright LCD, helping you navigate better and expedite critical decisions. The 320 x 240 pixel IR sensor and FSX™ Flexible Scene Enhancement produce detail-rich imagery at a 60 Hz frame rate that keeps up with the action.
-
product
Infrared Thermometer
DITH 120
Infrared Thermometer is also known as laser thermometerInfrared thermometer is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.Laser is used to help aim the thermometer or non-contact thermometers or temperature guns, to describe the device's ability to measure temperature from a distance. By knowing the amount of infrared energy emitted by the object and its emissivity, the object's temperature can often be determined. Infrared thermometers are a subset of devices known as "thermal radiation thermometers".The design essentially consists of a lens to focus the infrared thermal radiation on to a detector, which converts the radiant power to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature. This permits temperature measurement from a distance without contact with the object to be measured. A non-contact infrared thermometer is useful for measuring temperature under circumstances where thermocouples or other probe-type sensors cannot be used or do not produce accurate data for a variety of reasons.
-
product
Electronic Circuit Breaker Unit
The CorePower® DC or AC Electronic Circuit Breaker Unit replaces conventional thermal mechanical circuit breakers and functions as both a breaker and a switch for controlling loads. By placing ECBUs closer to loads, aircraft manufacturers gain a significant reduction in wire weight, need fewer system components, and lower installation labor costs while increasing safety, efficiency, and reliability. This new smaller unit requires less space and provides more flexible mounting options.
-
product
Laser Interferometers
ZYGO laser interferometers support and enable the most demanding metrology applications in industries from semiconductor and lithography to space-borne imaging systems, cutting-edge consumer electronics, defense-related IR and thermal imaging systems and ophthalmics.
-
product
Wafer Chucks
American Probe & Technologies, Inc.
High Performance Chuck for your needs Introducing the American Probe & Technologies’ HC-6000 series of thermal chucks,
-
product
Portable, Long-Range HD Thermal Imager
Ranger® HDC
The Ranger® HDC is a RealHD thermal imager with a 1280x720 cooled detector. Featuring the FLIR Image Processing Engine, the Ranger HDC provides exceptional long range thermal imaging performance and 22x continuous optical zoom to maintain situational awareness for effective target assessment.
-
product
Equipment & Vision Systems for Surveillance & Defense Applications
Photonis equipment systems are designed with Photonis sensors and cameras, while providing ease-of-use for in-depth image capture and analysis. These low light imaging systems are specifically developed with Night Vision, Observation & surveillance, Situation Awareness in mind.Two main equipments are proposed: the TacFusion is a handheld binocular combining low light camera core and thermal imaging sensor and the SR750 is a long range surveillance camera with powerful zoom and adapted ergonomics for rapid deployment. Both devices can be used for surveillance applications (police law-enforcement, borders and infrastructure surveillance) as well as SAR operations.
-
product
Battery Test Equipment
Shenzhen Bonad Instrument Co., Ltd.
The tests that can be performed by lithium-ion battery safety testing equipment include temperature cycling test, thermal abuse test, high altitude low-pressure simulation test, vibration test, shock test, external short-circuit test, forced internal short-circuit test, drop test, crush test, impact test, nail penetration test, burning test, etc. These test items mainly apply to various lithium-ion cells such as 18650 cells and prismatic cells, lithium-ion batteries, lithium-ion battery modules, lithium-ion battery packs, and so on.BONAD battery safety testing equipment complies with various standards such as IEC 62133, IEC 62133, UL 2580, UN 38.3, UL 1642, etc. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
-
product
Heat Flux Sensors
MF Series
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
-
product
Gauging System
Equator™ 300
Advanced Industrial Measurement Systems
The Equator is a flexible gauge that is designed to provide speed, repeatability and ease of use for manual or automated applications. The Equator is a highly valuable option for manufacturers who are looking to replace their current gauging method. Its system enables process control by delivering highly repeatable, thermally insensitive, versatile, and re-programmable gauging to the shop floor.
