PMC Modules
-
product
4-Slot BRIC, 256x4, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-401-256x4
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI Single 16 to 1 RF MUX SMB 75 Ohm
40-835-001
The 40-835-011 is a single 75 Ohm 16-channel RF MUX in a single PXI slot. The module has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40-835 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXI BRIC8 FIBO Matrix Dual 140x4 3pin brkout
40-592A-107
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
PXI 12-Slot BRIC Matrix, 336x6 1-Pole (4 Sub-cards)
40-558-121-336X6
The 40-558-121-336x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 15-Bank 40GHz SMA-2.9
60-802-415
The 60-802-415 is a 4-channel, 15-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
NI-9470, 5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module
787089-01
5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module - The NI‑9470 is a digital output module that features proportional valve drive control. You can use the NI-9470 to perform pulse width modulation (PWM), dither control, and current readback. The NI‑9470 features eight output channels compatible with signals from 5 V to 30 V and transient overvoltage protection between the output channels and the backplane.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 12-Bank 26.5GHz SMA
60-802-312
The 60-802-312 is a 4-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 75Ω, SMB
42-834A-002
The 40-834A-002 (PXI) and 42-834A-002 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXI 12-Slot BRIC Matrix, 35x32 1-Pole (7 sub-cards)
40-562B-321-35X32
The 40-562B-321-35X32 is a high density BRIC12 matrix module with a size of 35x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Dual 2x2 RF Matrix 2.5GHz 50 MCX
40-877-102
The 40-877-102 is a 50Ω 2x2 RF matrix with 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
LXI Microwave Multiplexer, SP4T, 7-Bank, 18GHz, 50Ω, SMA
60-803-107
Our 60-803-107 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI 8-Slot BRIC 72x8 Matrix, 2A 2-Pole (3 sub cards)
40-565A-102-72X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI 2A Multiplexer, 2-Bank, 16-Channel, 4-Pole
40-614B-012
This 2-bank, 16-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Single 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-001
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
PXI 16x4 RF Matrix 300MHz 50 SMB
40-727-001
RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors.
-
product
PXI 3A Power MUX BRIC, 15-Channel, 16-Pole
40-571-205
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-850A-214
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
90/120 GHz Dual Channel Optical Module
N1032B
The N1032B is a plug-in module for the DCA-X mainframe that includes two optical channels up to 120 GHz.
-
product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 3GHz, 50Ω, MCX
42-873A-101
The 40-873A-101 (PXI) and 42-873A-101 (PXIe) are 4 to 1 RF MUX with 1 bank in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
PXI BRIC8 FIBO Matrix Dual 6x2 3pin brkout
40-595A-001
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
product
PXI 8-slot BRIC Matrix, 128x8, 1 pole (2 Sub-cards)
40-558-801-128x8
The 40-558-801-128x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PCI 2 Amp Multiplexer, Quad 8-Channel, 1-Pole
50-635A-108
The 50-635A-108 is a quad 8-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI 8-Slot BRIC Matrix, 66x8 2-Pole (3 sub-cards)
40-562B-122-66X8
The 40-562B-122-66X8 is a high density BRIC8 matrix module with a size of 66x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
PXI 4 Slot BRIC 88x8 2-Pole (4 sub-cards)
40-562A-022-88X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI Very High Density Multiplexer, 10-Channel 8-pole
40-670C-021-10/8
The 40-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 11-Bank 26.5GHz SMA
60-801-311
The 60-801-311 is a 6-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI 3A Power MUX BRIC, 5-Channel, 48-Pole
40-571-005
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Rugged, Fanless AIoT Platform with NVIDIA Quadro® GPU Embedded for Real-time Video/Graphics Analytics
AVA-5500 Series
Artificial Intelligence (AI) technologies are being adopted globally by all industries to drive efficiency, improve productivity and reduce costs. The rail industry is no exception. Fueled by intelligence from AI-driven systems and applications, railway operations are becoming safer, smarter and more reliable, significantly enhancing passenger travel experience and freight logistics services. For rail transportation, AI can provide improvements including fast and convenient ticket-free check-in to accurate arrival-time predictions, personalized infotainment and onboard services, real-time track heath diagnostics, and rapid response in an emergency.
