Comparators
Contrast similar or divergent values.
-
Product
XP-Series Right Angle Air Screwdrivers
-
Crafted for high production environments, the Flex Power Right Angle air screwdriver provides durability, power and speed for assembly and manufacturing applications at an affordable price. Designed for safe operation and increase comfort for operators, the Flex Power tools provide lower noise decibels than comparative air tools as well as minimal vibration and low torque reaction on the operator. Featuring a patented clutch design the Flex Power tools delivers reliable accuracy with repeatable torque control. The clutch mechanism shuts off the air supply when the preset torque setting is achieved, preventing over-torque conditions from occurring.
-
Product
Camera Testing
FLIR
-
CI Systems' FLIR turn-key test stations carry out all the necessary tests to verify and compare the quality of an infrared/thermal camera. The FLIR test systems are based on CI Systems' NIST traceable blackbody radiation sources, collimators and special thermally controlled targets, designed to provide very accurate IR test patterns. All these combine to project standardized targets with known geometry and intensity to the Unit Under Test(UUT).
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
Differential Scanning Calorimeters
MicroCal DSC Range
-
The "Gold Standard" for structural stability analysis of biotherapeutics, biological macromolecules and polymers in solution. Are microcalorimeters are powerful tools which enable characterization of the thermal stability of proteins and other biomolecules, primarily for biopharmaceutical development and manufacture. They are used for general stability studies, for biosimilarity and batch-to-batch comparability assessment, and for the optimization of purification and manufacturing conditions. MicroCal PEAQ-DSC systems are simple to use, requiring little assay development, and no labelling or immobilization.
-
Product
Hardware Security For Programmable System Control
Mach-NX
-
*Up to 8.4K LC of user logic, 2669 kbits of user flash memory and dual boot flash feature*Up to 379 programmable I/O supporting 1.2/1.5/1.8/2.5/3.3 I/O voltages*Secure enclave supports 384-bit cryptography, including SHA, HMAC, and ECC*Configuration of PFR and security functions through Lattice Propel simplifies developer experience*Highly reliable. Low power and 3X better SER performance to comparable CMOS technologies
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
Mid-Range Gas Filter Correlation CO Analyzer
Model T300M
-
Teledyne Advanced Pollution Instrumentation
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.
-
Product
GPGPU Processor
VPX6-4955
-
Curtiss-Wright Defense Solutions
The VPX6-4955 delivers incredible processing power from not one, but two NVIDIA Quadro Turing TU104 GPUs, providing a remarkable 6144 CUDA cores for parallel processing and a 50% improvement in performance per CUDA core compared to the previous Pascal generation.
-
Product
Pressure Comparator (System E)
P014
-
AMETEK Sensors, Test & Calibration
The P014 hydraulic jack pump (System E) is an extremely effective pressure pump designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle.
-
Product
Optical Time Domain Reflectometer
-
Alnair Laboratories Corporation
The FDM-OTDR encodes multiple probe pulses at different frequencies, in the same time frame that conventional C-OTDRs send out a single pulse. This frequency-division-multiplexing enables larger data acquisition in the same measurement time compared to C-OTDRs. As a result the FDM-OTDR can achieve higher dynamic range with the same measurement time, or a significantly reduced measurement time with the same dynamic range.
-
Product
High Definition Mid-Range Surveillance System
Ranger® HDC MR
-
The Ranger HDC MR sets a new standard for surveillance with its ability to detect illegal activities even in degraded weather conditions, utilizing embedded analytics and image processing to reduce the cognitive workload, enabling operators to distinguish quickly between true threats and false alarms. The HDC MR is not only a superior system in bad weather, it also provides increased uptime and reduces cyber risks -- a reliable tool that adds days of efficient surveillance and reduces risk compared to previous generations of systems.
-
Product
Rock Mechanics
CLASROCK
-
The program classifies rock masses using both the Bieniawski and the Barton methods, making it thus possible to compare the results that can be obtained with the two most frequently used classification methods.
-
Product
Setup Integrity Checker For B2980 Series, Fixed Perpetual License
N1420A
-
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, 4.3-10, 2 Port
85094D
-
The Keysight 85094D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
Ultrasonic Portable Hardness Tester
UCI-3000
-
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Cryogenic Current Comparator (CCC)
6200A
-
Measurements International Ltd.
Introducing the Model 6200A Cryogenic Current Comparator Bridge (CCC) from Measurements International (MI) – the ultimate solution for achieving the highest level of resistance calibration accuracy. With an uncertainty of less than 3 parts in 10-9, our CCC surpasses all other technology on the market.
-
Product
2.5-inch IDE Disk Adapter
4946
-
The HDD is positioned midway such that the PMC component envelope is not violated. Furthermore, steel rails are attached to the printed circuit board, allowing for a secure, robust installation of the hard disk drive. This is a superior mechanical approach, compared with other printed circuit board-based solutions available on the market.
-
Product
Modular Test Toolkit
MTT Series
-
The MTT (Modular Test Toolkit) Series gives field personnel an all-in-one, low-cost platform for installing, verifying, and troubleshooting a wide variety of service technologies. The MTT family includes chassis configurations for diverse testing needs and budgets, and its upgradeable modular design means dramatically lower cost compared to purchasing separate dedicated test sets. Modules are available for multiple testing needs and applications, including metro, DSL, transport, optics, and service.
-
Product
Integrated Leeb Hardness Tester
TIME®510D
-
Beijing TIME High Technology Ltd.
TIME®510D is an updated version of TIME5120 Leeb Hardness Tester, the cheapest and most popular leeb hardness tester manufacturer by TIME. It is portable and integrated with universal impact device D. Compared to TIME5120, the new product offers significant improvements in both outlook and performance.
-
Product
Digital Tachometer
TM-3100 series
-
TM-3100 series is a new model of digital tachometer which responds to changes in diverse measurement objects by adding function in order to match your application.The each model of TM-3100 series has the most fundamental function in rotational measurement (display of rotation speed, BCD output, analog output or comparator output) and can be customized by adding optional cards.The fluorescent display tube of TM-3100 series greatly improves stability and readability instead of using LED as old models.
-
Product
20 GHz Signal Source
VCO Series
-
The SC5510A and SC5511A are VCO-based, synthesized signal sources with very low phase noise and an amplitude control of 0.01 dB throughout its -30 dBm to +15 dBm output power range. By utilizing a unique multiple phase-locked loop architecture, phase spurs are kept below -70 dBc across the entire tuning range, even at 1 Hz step resolution. Download the data sheet to see how the impressive features and specifications of these modules make them stand out when compared to other small modular synthesizers. These 20 GHz signal sources include an additional, independent RF2 channel with a tunable frequency range from 100 MHz to 3 GHz and a tuning resolution of 25 MHz. The extra channel makes the modules suitable for either single-stage RF conversion systems or dual-stage image suppression up/down converter systems. Both modules make great general-purpose laboratory signal sources where demanding low phase noise and signal purity are required. They are both ideal choices as an integrated clock source for fast DAC and ADC applications, especially those that require variable sampling rates. Full implementation instructions, GUI, driver software, and example code are provided with each module.
-
Product
MTF Measurement Station
ImageMaster PRO 10
-
As a result of various improvements the ImageMaster® PRO 10 enables customers to significantally increase their yield. It is the fastest and most accurate MTF measurement system on the market for qualifying mobile phone lenses and other miniature lenses. Besides the new software architecture and functions, the more precise mechanical components lead to best performance in accuracy, reliability and measurement speed. Faster MTF algorithms reduce the test cycle time so that an outstanding throughput is achieved. The ImageMaster® PRO 10 features a 15% increased productivity compared to the ImageMaster® PRO 9.The new ImageMaster® PRO 10 also provides additional measurement functions. For example, measurements at different frequencies and RGB measurements can be performed to determine chromatic aberration. An upgrade of four additional cameras allows the measurement of relative illumination for testing the homogeneous illumination of lenses in the field.
-
Product
Power Quality Analyzer
PQA820
-
PQA820 respectively record 383 and 44 quantities which can be recalled and dragged onto the screen to be compared between each other; for example, if you are displaying the trend of voltages and you want to check for the possible presence of harmonic distortion, it will be sufficient to scroll through the list of recorded measures and drag the one relevant to harmonics to the screen. The same can be done for all other quantities: power, cosphi, current, energy, etc.
-
Product
Munitions Testing
-
E-Labs has an extensive background in the development and testing of Less Than Lethal (LTL) devices. We were the first to develop a measuring system to capture blunt force or impulse of a round in real time. The Ballistic Impulse Measuring System (BIMS) developed by E-Labs was used on USMC programs to evaluate LTL rounds and compare impulses on a one to one basis.
-
Product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
782999-01
Relay Output Module
The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Product
Calibration Management Software
MET/CAL®
-
MET/CAL software is structured around the flow of instruments through the calibration process and addresses a wide range of test and measurement instrument calibration needs, from the simple to the complex. It is based on the traditional calibration model as its framework—comparing an instrument to a standard of known uncertainty.
-
Product
Optical Fiber Ranger
-
Optical fiber ranger is test equipment that functions similar to an optical time domain reflectometer. It is used in single mode fiber test applications. The fiber optic ranger is much smaller size and lighter weight compared to the fiber optic OTDR, and it is much more cost effective. They are used in optical fiber links troubleshooting, maintenance and test.
