Comparators
Contrast similar or divergent values.
-
Product
Gas Filter Correlation Carbon Dioxide Analyzer
Model T360
-
The Model T360 CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Biconical Antennas
-
For many years most standards called for the use of a half-wave dipole antenna set for frequencies above 80 MHz. However, to reduce test time, broadband antennas such as the biconical antenna and log periodic antennas began to be accepted. Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. A.H. Systems'' 7 models of Biconical Antennas operate efficiently over the frequency range of 20 MHz to 18 GHz. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Biconical antenna will provide reliable, repeatable measurements.
-
Product
48 Channel Threshold Comparator FPGA PXI Card
GX3748
-
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
Complete Pressure Systems
-
AMETEK Sensors, Test & Calibration
AMETEK offers a variety of solutions for pressure generation and measurement. Our line of products for pressure generation includes everything from small pneumatic hand pumps to a precision, hydraulic pressure comparator capable of generating up to 15000 psi/1000 bar/100 MPa.
-
Product
UNO Carrier Stack Supports MXM GPU Module Aims For Image Processing And AI Inference
UNO-MXM-CB01
-
1 x PCIe x4 expansion kit support 35W MXM GPUBundle compact Din-rail embedded PC form factor, UNO-148 series, with Intel® Core™ processors (13th/11th Gen)Expansion modules to accommodate MXM GPU module for powerful computing capabilitiesSupport 4 independent display outputs (3 x DP, 1 x HDMI)Standalone heatsink and fan for GPU stable performanceSupport up to 8GB GDDR6 with ECC (depends on MXM module option)Industrial design with longevity support (5 years life cycle compared to commercial GPU card 1 year)
-
Product
SPD AC & DC Thermal Stability Test Equipment
-
Shanghai Guantu Technology Co., Ltd.
1. Computer control measurement, PLC control;2. Equipped with sudden voltage capability, suitable for thermal stability tripping test under high current conditions;3. Increase the high-power resistance box;4. The interface is friendly and beautiful, and can reflect the running status of the system in real time; .5. Automatically draw voltage, current and temperature curves;6. The system performs multi-point temperature detection in real time;7. Timing sampling and recording function, which is convenient for users to view temperature values at different times and compare data;8.2 times Uc leakage current test function to check the tripping reliability of the product;9. Built-in test box;10. RS232 communication interface, can realize remote control.
-
Product
Torque Detectors
RH series
-
High rigidity: highly accurate detection of torque fluctuation with high response. The RH series is a torque detector that can accurately detect torque fluctuations with high torsional rigidity about 4.5 times compared to the existing products.
-
Product
Solar Array Simulator
-
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
Photolysis Rate Analyzer
PFS-100
-
, HONO, HCHO etc.) are key indicators for identify status & extent of photochemical pollution.The analyzer is receiving solar radiation by quartz probe and transferring the radiation to spectrum via optical quartz fiber, the spectrum data will be evaluated and compared with reference data with mathematical approach and gives photolytic rate.
-
Product
Ideal Remote Plasma Source For Oxygen-Based Processes
Rapid OX
-
Reduce recombination effects and extend the lifetime of oxygen radicals thanks to Rapid OX's removable quartz liner. When compared to anodized chambers, the resultant reactive species extended lifetime improves photoresist strip rates. And because the quartz liner is easily installed or removed by the operator, it decreases downtime and significantly lowers replacement costs.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
Gaussmeter
H3
-
The H3 Field Strength Meter is an electronically measuring bench unit with digital displaying used as desk or installation instrument with RS 232 Interface, double comparator and maximum value storage.
-
Product
Value DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285V
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsSupports linear and circular interpolationHardware emergency inputSupports E-GearSupports programmable acceleration/deceleration rateMemory buffer (10K points) for trajectory planning which is designed in DSP(Auto-blending is not supported)Position compares triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPPosition latchProgrammable interrupt and watchdog timerRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
Test Adapter
-
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
Product
EVISION Obstacle Detector
MS 1528
-
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
Product
Particle Analyzers
-
Teilch Particle Analyzers have proven significant advantages when compared to competitors’ solutions. Innovations in light source, flow control, analog and digital signal processing, components integration and software allow Teilch to provide a state of the art system for precision particle analysis.
-
Product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
-
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength and a good field uniformity is required. The beamwidth in the E-plane and the H-plane are nearly identical, providing an optimised illumination of the EuT with minimised ground reflection influence. Further the STLP 9128 C has an excellent cross-polar rejection.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
Industrial QC/QA Analyzer - "Column Free" Molecular Fingerprinting Technology
Aqualog - A-TEEM
-
A-TEEM™ Molecular Fingerprinting is a new optical technique that is ideal for comprehensive component analysis in a variety QC/QA applications, from water to wine to pharmaceuticals and more. It is a simple, fast, “column free” spectroscopic technique that simultaneously measures the absorbance, transmission and fluorescence of samples in solution, and offers unique benefits over traditional analytical techniques, such as chromatography, mass spec, IR, etc.. Fundamentally, this technique is best applied to samples in solution that have fluorescing components, like an aromatic molecule, although it also detects non-fluorescing species via absorbance. The fluorescence EEM fingerprint technique has also been applied to solids and skin. Fluorescence is a highly sensitive technique compared to other spectroscopic techniques such as absorbance, FTIR and Raman, and the three-dimensional nature of the data provides for a better foundation for complex component analysis.
-
Product
Arbitrary Function Generator PXI Card
GX1200/GX1201
-
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
Solid State Relays
-
Vishay’s solid-state relays (SSRs) are designed for high reliability, high input-to-output isolation, and low on-resistance. With small dimensions, low power consumption, and bounce-free operation, they offer many advantages compared to mechanical relays. Vishay SSRs are perfectly suited to replace mechanical relays and are the ideal solution for signal switching in telecommunications, industrial automation, security systems, and metering applications.
-
Product
Circuit Breaker Operational Analyzer
CBScan
-
CBScan is a compact and portable circuit breaker analyzer. It has limited number of channels as compared to AutoScan, but is ideal for basic shop-floor and on-site testing requirements. This analyzer has complete functionality of AutoScan. However, to ensure portability, an external laptop is required to run the test software.
-
Product
Field-installation Type Dissolved Oxygen Meter (Four-Wire Transmission, Optical Type)
HD-200FL
-
Optical dissolved oxygen sensor with no electrolyte replacement and rugged membrane.Highly intelligent, including automatic recognition of membrane properties when replacing the sensor cap.The HD-200FL is an optical (fluorescent) dissolved oxygen meter suitable for monitoring aeration tanks used for sewage treatment, effluent treatment, and other processes. Compared to conventional membrane polarographic type sensors, there is no need for electrolyte (internal fluid) replacement or warming, up. Characteristics of optical sensors are utilized to realize unequaled, improvement in ease of maintenance and reduction in running costs. Moreover, it features enhanced user-friendliness, with sensor caps that have built-in memory and a membrane replacement notification function.
-
Product
Chloride Test System
C-CL-2000
-
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
Product
NeuroSensory Analyzer
TSA-II
-
TSA thermal stimulator test procedure The test procedure itself is similar to that employed in such routine tests as eye and hearing examinations, where patients are asked to respond to visual or auditory stimuli. Sensory testing is performed by applying the TSA-II thermode on the patient's skin to heat or cool the skin. Patients respond to the temperature stimuli by pushing a button, and the sensory threshold is recorded and automatically compared to an age-matched normative data.
-
Product
Saluki S2108 Series Optical Network Tester (up to 45dB)
-
Saluki S2108 series Optical Network Tester is an intelligent high-precision optical network comprehensive tester with cloud wireless transmission, intelligent cloud platform and other functions. S2108 series adopts 7 inch capacitive touch screen, supports multi-point touch and integrates 18 functional modules internally. Compared to previous versions, it supports smart cloud platform, iONM, Multi-core measurement, 4G LTE SIM, GPS, Bluetooth and WIFI; built-in 8G storage capacity, can store more than 200,000 test data, and test data can be uploaded to the cloud wirelessly; PDF reports can be generated on the device and transmit them to the mobile terminal via WiFi & Bluetooth. S2108 series supports multi-tasks simultaneous operation, and VFL, OPM, LS functions can run in the background.
-
Product
XRF
G Series
-
The G Series’ two most distinctive features are precision video imaging, and “bottom-up” measurement using a motorized Z-axis with laser-based auto-focus. The latter is a feature unique to Bowman. An available manual XY stage with 1.5 X 1.5” travel facilitates easy positioning of small and large parts. The chamber is relatively small when compared to other models like the B Series. The smaller chamber and footprint is well suited for jewelry and other precious metal analysis applications, and components such as connectors and fasteners.
-
Product
Electronic Pressure Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
When it comes to simultaneous pressure calibration for several pressure measuring instruments, electronic pressure comparator is always a great choice for most of people. The comparison calibrator features 5 pressure ports which allow simultaneous connection of 4 pressure gauges under test, making calibration more efficient and time saving. It also comes with an external air source for easy and precise pressure generation and servo valve for stable pressure control.
-
Product
Thermistor Power Meter
N432A
-
Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.
