Filter Results By:
Products
Applications
Manufacturers
Comparators
Contrast similar or divergent values.
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
product
Partial Discharge Inductor
Tracy
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
product
Logic Probes
Logic probes are used to analyze the logic states (high/true: logic 1 or low/false: logic 0) of digital signals. To verify and debug today’s high-speed, low-voltage digital signals, you need logic probes that can accurately acquire signals from a wide variety of electronic designs, while protecting signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions below.
-
product
Torque Meters
Torque meter is available in two different versions: handheld meters or tabletop meters. Torque meter have a wide range of applications. Handheld torque meter is mainly used for industry while tabletop torque meter is the ideal tool for laboratories. Our Torque meters come with a RS-232 port to transfer torque values to a PC or a portable computer. This is very helpful if you want to save the data and stand the chance to compare what you have measured afterwards. Another possibility is that you aim to do long-term-measurements. There the interface and the software are two very useful features that are given to you.Tabletop torque meters can be equipped with a printer (option). You can also order a ISO calibration certificate as an option. This ensures that the device has been calibrated and works perfectly including a measurement with only small deviances that can still be tolerated and do not influence the product's functions. We can offer you torque meters that can measure up to a maximum measuring value of 500 Nm.
-
product
Near Field Probes
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
product
2D Antenna Pattern Measurements
The world's top antenna manufacturers utilize MET Labs for 2D Antenna Pattern Measurements to compare an antenna's real-world performance versus its theoretical performance
-
product
FFT Comparator
CF-4700
The CF-4700 FFT comparator is a pass/fail judgment machine used on production lines that is highly effective in accurate quality inspection by analyzing sound or vibration from products. As being incorporated our accumulated FFT technology over the years, the CF-4700 enables pass/fail judgment by extracting the amount of fluctuation of signal size focusing on a specific frequency band.
-
product
Fast Timing Analysis
Zero-Time Box
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
product
PNA-X Measurement Receiver for Antenna Test
N5264B
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
product
Comparator
Delta Colour Comparator 3000
The comparator consists of two wheels in which nine colour glass filters are retained in each of the wheels. The colour range goes from water white through deep amber. A tube of the sample liquid is placed between the two filter wheels. The user then rotates the wheels until the filter glass closet in colour to the liquid is in place, the nearest match to the sample becomes the designation of the liquid.
-
product
Digital Gauge Counter
DG-2310
Model DG-2310 is a 2-channel digital gauge counter with multi function to measure and display the dimension and displacement by using our linear gauge sensors (BS/GS-series).Not only the various calculating function of addition/subtraction (A+B, A-B) for 2 channels' data but also that of Max., Min., Range (Max. - Min.) are provided.OK/NG judgment and alarm operation are also possible by using the comparating function.Further, the sequencer, personal computer, recorder and other instruments can be operated by inputting the various signal output from DG-2310, which can make it possible for the data recording and monitoring easily.
-
product
Electric Double Layer Capacitors (Gold)
Panasonic Industrial Devices Sales Company of America
Panasonic Electric Double Layer Capacitors, known as “Gold Capacitors”, offer the highest volumetric efficiency of all capacitor technologies. They are often compared to secondary batteries.
-
product
Spectrum Analyzers
A refurbished spectrum analyzer is the best solution if you are looking to stretch your budget. The spectrum analyser is typically a more expensive piece of test equipment when compared to other general purpose test instrumentation. Depending on your test needs and budget a new spectrum analyzer may be the preferred choice. We have a very wide selection for you to choose from and a product for every budget.A spectrum analyzer is found in three basic forms, bench top, handheld, and portable. The spectrum analyser enjoys a long useful life and good resale value because of its fundamental use, the measurement of the spectrum of a signal. Microprocessor speeds change but frequencies do not. Basic and real time signal and spectrum analysis is always a test need especially now given the wireless world we live in. As wireless consumer and industrial devices continue to come on the the market, the spectrum analyzer can be found in more and more design, in house test, manufacturing, quality, field test, and remote repair applications.Test Equipment Connection offers Spectrum Analyzers in a various range of prices and categories, allowing you to find the equipment you need. Search by Frequency, number of channels, brand or price range. Test Equipment Connection has made it easy to find the equipment that is right for you.
-
product
Sliding Peel Strength Tester
OST3000
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
product
Remote Terminal Unit (RTU) Replacement
Schweitzer Engineering Laboratories, Inc.
Compared with typical RTUs, SEL automation controllers provide improved reliability, extended I/O contacts, and advanced automation and control for remote substations and field applications.
-
product
CPU RightMark
CPU RM
The CPU RightMark suite is meant for objective measurement of performance of modern and future processors in different computational tasks such as numerical modeling of physical processes and solving of 3D graphic problems. It focuses on testing the loaded FPU/SIMD units and the CPU/RAM tandem. As a result, we get pure CPU performance, an objective parameter obtained without the influence of other subsystems, like video and disc systems, except the memory one. It allows us to compare the true performance of different processors irrespective of a type of other system components. It's obtained by dealing only with the CPU and measuring the CPU time spent for execution of computational tasks.
-
product
Network Interface Controller
SPIDAR®
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
product
Saluki SE1022 DSP Lock-In Amplifier
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
-
product
Power ICs - Smart Load Switches
Combining multiple functions in a single IC, Vishay smart load switches eliminate the need for external circuitry . A simplified GPIO interface allows for power distribution and sequencing of multiple sub-systems. Slew-rate-control devices provide a controlled supply ramp to reduce inrush current, while fault protection and isolation switches increase robustness with reverse current, overtemperature, current limiting, and short circuit protection features. The ICs offer quick output discharge and small footprints, while their integrated design saves PCB space compared to discrete solutions, reduces BOM counts, and lowers manufacturing costs.
-
product
Biconical Antennas
Biconical Antennas have dipole like characteristics (e.g. circular directional pattern in the H-plane,"8"-shaped in the E-plane, fixed phase center, comparable gain), with an enormous wide bandwidth achieved by the double cone elements.
-
product
Integrating Spheres
IP-Series
Photometric Integrating spheres are used for evaluation of luminous flux of light sources & luminaires with a single measurement & for comparative analysis. The sphere is an essential tool for photometric research laboratories & lamp/luminaire manufacturers.
-
product
Mid-Range Gas Filter Correlation Carbon Dioxide Analyzer
Model T360M
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Flying Probe PCB Test and Repair System
GRS500
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
product
Battery Pack PCM Test Equipment
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
product
Automatic Current Transformer Comparator
KATC-C2
Got older, slower equipment? Knopp’s Automatic Current Transformer Comparator (KATC-C2) is faster, more robust and more accurate! Knopp’s KATC-C2 is a high accuracy current comparator that is compatible with all older generation Knopp comparators, and is designed to be a direct, plug-in replacement requiring no modification of the existing Knopp Current Transformer Test Systems. Save time and money on service by upgrading your comparator to our new next generation model!
-
product
Cryogenic Temperature Sensors
Cernox®
Cernox® thin film resistance cryogenic temperature sensors offer significant advantages over comparable bulk or thick film resistance sensors. The smaller package size of these thin film sensors makes them useful in a broader range of experimental mounting schemes, and they are also available in chip form. They are easily mounted in packages designed for excellent heat transfer, yielding a characteristic thermal response time much faster than possible, with bulk devices requiring strain-free mounting. Additionally, Cernox sensors have been proven very stable over repeated thermal cycling and under extended exposure to ionizing radiation.
-
product
Gas Filter Correlation Carbon Dioxide Analyzer
Model T360
The Model T360 CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Field-installation Type Dissolved Oxygen Meter (Four-Wire Transmission, Optical Type)
HD-200FL
Optical dissolved oxygen sensor with no electrolyte replacement and rugged membrane.Highly intelligent, including automatic recognition of membrane properties when replacing the sensor cap.The HD-200FL is an optical (fluorescent) dissolved oxygen meter suitable for monitoring aeration tanks used for sewage treatment, effluent treatment, and other processes. Compared to conventional membrane polarographic type sensors, there is no need for electrolyte (internal fluid) replacement or warming, up. Characteristics of optical sensors are utilized to realize unequaled, improvement in ease of maintenance and reduction in running costs. Moreover, it features enhanced user-friendliness, with sensor caps that have built-in memory and a membrane replacement notification function.
-
product
Blood Ionized Calcium Pocket Water Quality Meters
LAQUAtwin Ca-11C
Milk fever, or Sub Clinical Hypocalcemia (SCH) is a significant problem with dairy cows. Total calcium levels in the cows’ blood drop after lactation. By measuring the ionized calcium levels of the blood directly cow side, the treatment can start sooner and is more effective. The new LAQUAtwin CA-11C has been specially developed for cow side measurement of ionized calcium in blood. Ionized calcium reflects more accurately the current calcemic blood situation compared to total blood calcium as it equals the free available calcium ions.
-
product
LXI EMR Low Thermal EMF Matrix 14x33
60-511-004
This high density 1-pole matrix has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix.
