-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
RFSoC Board
VP430
-
RFSoC on 3U VPX: the VP430 direct RF system features an RFSoC with integrated ADCs, DACs, programmable FPGA logic, and Zynq ARM Cortex processor.
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-01
Current Input Module
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-013-HI
-
The 40-230-013-HI (PXI) and 42-230-013-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 1.81kΩ
40-251-122
Programmable Resistor Modules
The 40-251-122 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Geospatial Data & Imagery
-
L3Harris Geospatial Solutions, Inc
Since 1951, we have provided customers with cutting-edge geospatial data and imagery products. Through the years, we have earned a reputation as an unbiased consultant who identifies the right data to solve customer’s problems and meet specific project requirements. Our highly-skilled staff of photogrammetrists, programmers, and imagery scientists draw upon their vast experience as well as access to a multitude of data types from the top vendors around the world. We offer the most robust selection of geospatial products worldwide including high-resolution, commercial satellite imagery, aerial maps, digital elevation model (DEM) data, topographic maps, and more.
-
Product
*Control IPC
AMAX-5000 Series
-
AMAX-5000 is an EtherCAT Slice I/O and controller platform designed with the smallest programmable automation controller (PAC) in the Core i class.
-
Product
Autoranging System DC Power Supply, 80 V, 510 A, 15000 W, 208 VAC
N8931A
DC Power Supply
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
-
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-051-HI
-
The 40-230-051-HI (PXI) and 42-230-051-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-243-HI
-
The 40-230-243-HI (PXI) and 42-230-243-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 770kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
DC Power Module, 8V, 12.5A, 100W
N6742B
Power Module
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Power Supply System
PL516
-
The PL516 is a high sophisticated, high density, programmable 16-channel with full redundancy low-voltage power supply system. Using the remote monitoring and control features it can be used to supply a large numbers of external load- channels with high power consumption also over long distances.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-026
Programmable Resistor Modules
The 40-254-026 (PXI) and 42-254-026 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 26.7kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXIe-5113, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope
786375-01
Oscilloscope
PXIe, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5113 oscilloscope has two channels that sample up to 3 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 500 MHz of analog bandwidth.
-
Product
12 D/A Outputs (±10 VDC or ±25 mA)
DA1
-
The DA1 module features 12 independent D/A output channels with a full-scale range of ±10 VDC at ± 25 mA (max). The DA1 provides either voltage or current control loop modes that are programmable for the particular application. The DA1 module also offers external trigger/synchronization signal (RS422/485) capability, which provides/accepts a trigger signal to/from other module(s).
-
Product
Electronic Loads
T3EL Series
-
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
Product
PXI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module
778967-01
Digital I/O
64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PXI‑6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Laser Diode Drivers
-
Arroyo Instruments offers a broad range of laser drivers to meet your exact test needs. From 100 milliamps to 100 Amps, all of Arroyo Instruments' LaserSource benchtop laser drivers include unique features not found on competing products such as optically isolated photodiode and modulation inputs, programmable PD bias, and both RS232 and USB computer interfaces. The LaserSource also has laser diode protection circuits such as interlock, ESD protection, and hardware limits for current and voltage.
-
Product
DC Power Module, 35V, 3A, 105W
N6744B
Power Module
The Keysight N6744B is a 105 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-026
Programmable Resistor Modules
The 40-297A-026 (PXI) and the 42-297A-026 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 26.7 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-015-HI
-
The 40-230-015-HI (PXI) and 42-230-015-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 925Ω with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5791
-
- Simultaneous synthesis of up to five different clocks- Eight SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
Programmable Delay Line Instrument
XT-100-OEM
-
With the XT-100-OEM, all the capabilities and precision of the XT-100’s trombone technology can be built right into your own system. This product is intended primarily for OEM applications so you have a streamlined solution for precision phase shift or programmable delay.
-
Product
Programmable Insulation/Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. Electric safety wall detecting2. Test mode programmable3. ACW to DCW to IR toggle automatically4. (40.0~400.0)Hz
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-323-HI
-
The 40-230-323-HI (PXI) and 42-230-323-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-155-HI
-
The 40-230-155-HI (PXI) and 42-230-155-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
