-
-
product
Digital Combo Set for Measuring Low-Frequency Signals
SVG-5
- Measurement of root-mean-square AC voltage and frequency of single-ended or differential signals- Measurement of AC voltage frequency of single-ended or differential signals- Generation of sine waves- Visual examination of freeform signals- Signal spectrum analysis
-
product
Multifunction Voltage and Current Calibrator
MC140i
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
product
Lightweight, Compact, Fully Enclosed/Shielded Power Converters
Series RKE
These lightweight (less than 7 lbs.), compact (less than 160 cubic inches), fully enclosed/shielded power converters deliver either 24, 36 or 48 volts d-c, to run distributed power systems, motors, actuators or heaters. Their universal a-c input (85-265V a-c) is at home with either 115V a-c or 230V a-c, though they produce significantly more output at the higher input voltage, and should be run from 200-240 volt mains wherever possible.
-
product
MRI Power Supplies
MRI Power Supplies are used in MRI Imaging rooms in hospital environments. The lights in the MRI rooms require DC power. If AC power is used, the quality of the MRI imaging process is compromised. These units are ideal for the MRI room, where a 60 Hz flicker-free light environment is desired. CEHCO offers four models which are shown below.
-
product
Battery Analyzers
BA6010 Series
The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians. The BA6010 Series is suitable for characterizing battery chemistries that are responsive to a 1 kHz AC stimulus signal including lead acid, lithium and alkaline type batteries used in consumer products, electric vehicles, power backup, security, and fire alarm systems.
-
product
DIGITAL MULTIMETER, TRUE RMS, 10A, 1KV
72-13570
*True RMS digital multimeter with 40000 counts display*CAT III 1000V, CAT IV 600V safety rating*Manual function select and auto ranging*Measure AC & DC at the same time (AC+DC)*Up to 9999 readings data storage and 0.1% to 99.9% duty cycle*Data hold, max/min/relative modes, analogue bar graph*Full icon display, double backlight*USB interface and Bluetooth connection*Powered by 9V (6F22) battery*12-month limited warranty *view Terms & Conditions for details
-
product
Wireless LAN Module
SX-SDMAC2
The SX-SDMAC2 is a dual band IEEE802.11 a/b/g/n/ac WLAN and Bluetooth 5.0 BR/EDR/LE (Class1) module based on Qualcomm QCA9379-3 chipset. It supports 2x2 antenna configuration for applications that require higher performance. Silex has separated the Bluetooth antenna from the Wi-Fi by creating a third antenna port, allowing concurrent operation of Wi-Fi and Bluetooth further optimizing the Wi-Fi and Bluetooth performance.
-
product
Hipot Line Testers
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
product
Power Supply, 150 V, 22 A, 3300 W
N8740A
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8740A is a 150 V, 22 A, 3300 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-80H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High precision clamp type ZCT sensor*Big CT window,φ80mm*AC 0～10A*Least affection from the external magnetic field and residual current
-
product
Portable System for High-Voltage Solid Dielectrics Testing
HVT-70/50
Portable system HVT-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
product
AC Magnetic Measuring Equipment
Is used for measurement analysis of magnetic characteristics in high frequency by commercial frequency of soft material sample
-
product
Variable Transformer DC Power Supplies
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
-
product
Test Equipment
Digital Clamp Meter
Is a large AC current digital multi clamp meter, integrated with 2000 Count, True RMS, auto and manual measurement, air-cored coil sensing technology.
-
product
2 Channels, 2-28 Vrms, 47 Hz-20 kHz (max. range), programmable
AC2
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
product
Bench-top Digital Power Meter
GPM-8213
GW Instek GPM-8213 power meter is designed specifically for single-phase (1P/2W) AC power supply’s power measurements. Powerful features, including 4” TFT LCD, five-digit measurement display, 19 power measurement parameters, integral measurement function, high-accuracy voltage/current/power measurement capabilities, front/rear panel input terminals, and various communications ports, are to facilitate users with clear, convenient, and accurate power measurements.
-
product
Current Transformers
Excellent measurement technology requires high-quality current transformers. The product portfolio comprises a wide range of current transformers for load currents (operating currents) and residual currents (RCM). Different designs cover a variety of installation situations and metrological requirements, and enable retrofitting. AC/DC sensitive measuring current transformers use a special measurement method to detect both AC and DC currents of different frequencies.
-
product
Power Supply, 40V, 38A, 1520W
N5766A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight 1520W, single output N5766A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers solid performance and a variety of basic and enhanced capabilities in a compact 1U package.
-
product
Signal Conditioners
Our load cell signal conditioners / amplifiers are just the thing when a digital display is not required, for example, applications in which the weighing system is controlled or monitored by a computer or PLC. These units supply the needed excitation voltage to power up the load cell(s). The wide range of models offered provide a variety of accuracy and frequency response levels, and signal outputs such as 0-10VDC, +/-10VDC, 4-20mA, RS232, RS485, USB, and frequency. Both AC & DC powered units are available.
-
product
Multifunction Electrical Installations Meter
MPI-525
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
product
Aftermarket Automotive Leak Detection
LeakFinder
The LeakFinder brand is Tracer Products cost-effective solution for end-users in the automotive aftermarket. LeakFinder products are made for DIY jobs and small to mid-sized automotive repair shops. They are the perfect tool for finding small, sporadic leaks in automotive A/C and fluid systems.
-
product
Three-Phase Transformer Demagnetizer
DEM60C
After a DC current test, such as winding resistance measurement, the magnetic core of a power or instrument transformer may be magnetized (remnant magnetism). It can cause various problems such as wrong diagnostics, inaccurate measurements on a transformer, inrush current at the start-up of a power transformer, or incorrect operation of protective relays due to magnetized CT cores. The best way to eliminate this source of potential problems is to use demagnetizer on the power or instrument transformer.The DEM60C is a fully automatic test instrument which performs three-phase transformer demagnetization. Transformer magnetic core demagnetization requires the application of AC current with magnitude decreasing to zero. DEM60C provides this AC current by internally changing the polarity of a controlled DC current. During the demagnetization process, the instrument supplies the current at decreasing magnitude for each step, following a proprietary algorithm. It can demagnetize single-phase and three-phase power transformers.The instrument can be connected to all three phases of a power transformer to be demagnetized, on either the primary or the secondary side. If a user selects specific vector diagrams for different types of transformers, DEM60C will run a specific demagnetization procedure for each transformer type (i.e., single phase, delta, wye/star, zig-zag.) without switching the test leads.DEM60C enables safe and efficient power transformer demagnetization. The instrument automatically regulates the injection of current and discharging energy from the inductance. During and after the operation, an intrinsically safe discharge circuit with an indicator rapidly dissipates the stored magnetic energy. The discharging circuit is independent of the power supply, which improves its reliability in case of loss of power.Test currents of up to 60 A DC enable efficient demagnetization of even the largest power transformers. Using a DV Win software, it is possible to control DEM60C externally.
-
product
Digital Earth Resistance Tester
ERT-1501
Electronic Digital Earth Resistance Tester is direct replacement of the conventional hand generator type tester. It is designed for measurement of the resistance of earthing used in the electrical equipment as well as for measurement of ground resistivity. It can be used for measurements of the other low regular and liquid resistances. It can also be used for measurement of voltage AC, voltage DC and resistance. This instrument finds wide application for testing earthing installation in power based industries, telecommunication networks and electrical traction systems etc.
-
product
Hand-hold Field Intensity Meter
LM870-N
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Spectrum displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
product
AdvancedTCA, Type 11A, 3U 19" Horizontal, AC
11A02FJB38Y4HGBX
Elma's ATCA, AC, 3U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
product
Discharging Bars
VARIO discharge products consist of a separate AC power supply for connecting one or more Eltex discharging components. In SINGLE discharging, the voltage generation (power supply ) is integrated in the bar.
-
product
HeNe Laser System with Built in Receiver and Power Supply
5519B
The Keysight 5519B Laser is a Helium Neon Laser (HeNe) that offers exceptional stability. The laser is a complete system with a built-in receiver and its own power supply that plugs directly into an AC power outlet.
