Accelerometers
convert acceleration into electrical signals, usually denoted as a
See Also: Gyros, Gravimeters, IMU, Gyroscopes
-
product
SparkFun Triple Axis Accelerometer Breakout
ADXL345
This new version adds two standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.
-
product
Biaxial Inclinometers
Columbia Research Laboratories
Columbia's Biaxial Inclinometers use the same force balance accelerometer technology used in our single axis inclinometers. These Biaxial Inclinometers are used in applications where dual axis tilt measurements are required. The SI-702B series is intended for use in applications such as platform stabilization, surface mapping and measuring tilt angles in remote locations. The SI-701AI series, is designed with an output circuit configuration made for use in 4-20mA data transmission systems.
-
product
General Purpose Triaxial Piezoelectric Accelerometers
Triaxial accelerometers provide simultaneous measurements in three orthogonal directions, for analysis of all of the vibrations being experienced by a structure. Each unit incorporates three separate sensing elements that are oriented at right angles with respect to each other.
-
product
General-purpose Accelerometer
MTN/1100
General-purpose accelerometer with isolated AC outputs, ideal for vibration analsis and for use in harsh environments.
-
product
SparkFun Triple Axis Accelerometer Breakout
MMA8452Q
This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data.
-
product
High Temperature
PCB® offers specially designed and tested ICP® and charge mode accelerometers for testing in extremely high temperatures.
-
product
Dual-Axis Accelerometer For HS5 & 6 Handyscopes, +/- 2G
TP-ACC20-09
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least +/- 2G.
-
product
General Purpose Piezoelectric Accelerometers
Piezoelectric accelerometers offer tremendous versatility for shock and vibration measurements. These rugged sensors can withstand adverse environmental conditions. A wide variety of configurations are available to support multiple application requirements. Specialty units are also available through mechanical or electrical design modifications or additional qualification testing.
-
product
Bump Tester
KD-163
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
product
IEPE Monoaxial Accelerometer – 100 mV/g
HDP352C34
Monoaxial accelerometer general purpose, ICP, 100mV/g, weight 5,8 g, range 50 g pk
-
product
Wafer Probe Test System
STI3000
The STI3000 is a wafer-level MEMS and mixed signal ASIC probe test system that combines several functional STI test equipment blocks for testing gyros, accelerometers, pressure sensors, microphones, resonators, and mixed signal ASICs.
-
product
Motor Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
product
Accelerometer
AP2038
Combination of high axial sensibility, intrinsic frequency, and shock resistance; Low sensitivity to electromagnetic fields; Feed voltage and current wide range; Low intrinsic noise level.
-
product
Biaxial Linear Accelerometers
Columbia Research Laboratories
The line of Biaxial Force Balance Linear Accelerometers available are 2-axis versions of our General Purpose, Low Noise and High Temperature, and High Performance Single axis Linear Accelerometers.
-
product
Motion Simulator For Test Systems
Metis
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
product
Accelerometer & Platform Test Bench
mS 1115
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783362-01
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
product
Inertial Measurement Units
IMU
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
product
Vibrator QC System
Accelerometer Array
*24-channel input interface for DAQLink-III acquisition system (23 for accelerometers and one for True Reference)*Computes accelerometer weighted sum using input array*Controlled state of current supplies for external accelerometers*LED status indication of every accelerometer input*Differential outputs to the acquisition system*Input channel impedance of 1 Mohm*Bandwidth: 0.1 - 5000 Hz*Crosstalk: -100 dB*Phase tolerance of channels: ±0.2 deg*10 mA current supply for every accelerometer channel*Max input signal: ±10 V p-p (True Reference), ±2.8 V p-p (Accelerometer input)*Power supply: 9 - 18 V
-
product
High Temperature ICP® Accelerometers
PCB® offers specially designed and tested ICP® accelerometers for conducting vibration and shock measurements under demanding environmental conditions of up to 356 °F (180 °C). These sensors combine proven quartz and ceramic shear sensing technology with specialized, built-in microelectronic signal conditioning circuitry to achieve dependable operation in extreme temperatures and through repetitive temperature cycling. Laser-welded, hermetically sealed, lightweight titanium or stainless steel housings offer further protection from the environment. Prior to shipment, each sensor undergoes a battery of tests to ensure survivability for its intended use. Such tests include temperature soak at elevated temperatures, temperature cycling, and exposure to highly accelerated screening procedures with hydraulically actuated shakers.
-
product
Piezo-resistive Accelerometer
A Piezo-resistive Accelerometer has a stable structure composed on a silicon chip created by the micromachining and semiconductor production technology. A mass and a beam on which a set of the Piezo-resisters are created on the silicon chip. A set of electrical bridged is formed by such Piezo-resistive resisters to generate signals proportional to the applied acceleration.
-
product
Piezoelectric
Columbia Research Laboratories
The Columbia product line of piezoelectric accelerometers is widely known for reliable performance, quality and ruggedness and is always expanding to meet the unique challenging and ever changing requirements of our customers. The selection of specifications, sizes and configurations is large and diverse and suitable for use on many applications requiring features such as, high performance, high accuracy, high temperature, seismic event, 4-20mA output, airborne, miniature size and general purpose use.
-
product
Endevco Piezoresistive Undamped MEMS Accelerometers
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
PCB Triaxial Accelerometer, 1000mV/g, ICP®(IEPE), 0.5Hz-3kHz
784815-01
The PCB Miniature Triaxial Accelerometer helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB Miniature Triaxial Accelerometer features a sensitivity range of 1000 mV/g and requires the PCB lightweight cable with 4-socket plugs.
-
product
Vibration Testers
Guangzhou Amittari Instruments Co.Ltd
The Vibration Tester can display the parameters of “Displacement”, “Velocity” and “Acceleration” simultaneously; Applied to the periodic motion measurements to detect moving mechanical imbalances and misaligned. Designed for on-site measuring various mechanical vibration, for quality control, running time and prior equipment maintenance data. Selection of high-performance accelerometers to achieve accurate, replicable measurement It has a bearing condition measurement function.
-
product
IEPE Triaxial Accelerometer – 1000 mV/g
HDP356B18
Triaxial accelerometer high sensitivity, ICP, 1V/g, weight 25g, range 5 g pk
-
product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
product
Calibration Systems
Brüel & Kjær Sound & Vibration A/S
Our calibration solutions meet the broad variety of needs for calibration in the field of sound and vibration accurate primary and secondary calibration of measuring equipment and the scope of transducers: accelerometers, microphones and hydrophones.
-
product
Vibration Calibrator
SV 111
SV 111 vibration calibrator is the State of the Art instrument designed for human vibration measurements according to ISO 8041. The design of the calibrator is based on the triaxial reference accelerometer and microprocessor controlled shaker. These both features assure excellent stability of the calibration levels and their frequency independently from mass of the testing object, like also indicate improper test object fixing by monitoring of shaker vibration in all three axis simultaneously.
