Phase
the difference between two features of a waveform, measured in any of multiple manners (distance, time, angle, wavelength, etc.)
See Also: Phasing, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Time
-
product
Programmable AC Power Source
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
product
Harmonics and Flicker Testers
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
product
D-Type Flip-Flops
Advanced Science and Novel Technology, Co., Inc.
High speed broadband D-Type Flip-Flop for data retiming with full rate clockExhibits low jitter and limited temperature variation over industrial temperature range6.5ps set-up/hold time capability87% clock phase margin for retiming of data input eyeFully differential CML input interfacesFully differential CML output interface with 400mV single-ended swingSingle +3.3V or -3.3V power supplyPower consumption: 415mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
product
Low Power Programmable AC Source with Transients
61500 Series
Chroma Systems Solutions, Inc.
Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface
-
product
f/1.3 Modular Spectrometers
Raman
Our f/1.3 modular spectrometers can be configured for fiber couple or free space. They use our proprietary volume phase holographic gratings paired with f/1.3 optics. This allows us to build a high-performance spectrometer in a small package. These spectrometers constantly outperform larger more expensive units. They have high throughput and are ideal for applications that demand fast integration times or for low light applications.
-
product
LCR Meter
*Rs, Rp, Cs, Cp, Ls, Lp, phase angle, Dissipation factor, Quality factor *Auto select series or parallel test mode *Auto select 100Hz/1kHz/10kHz test frequency, 0.5V rms approx. *Calibration
-
product
AC Power Sources
400XAC Series
Our 400XAC Series AC Power Sources provides both 1Ø and 3Ø AC or DC power in a single box solution. If you need an AC Power Source with superior application flexibility, look no further than the EEC 400XAC. Ideal for both production and laboratory use, this 3 phase AC Power Source provides a unique feature set at a competitive price point. Our exclusive SmartCONFIG feature allows the 400XAC Series to switch from 1 phase to 3 phase power with the push of a button. This flexibility maximizes your investment while providing you the AC and DC power that your application needs. The 400XAC Series AC Power Source includes the following models: 430XAC and 460XAC.
-
product
Phase Shifters
Essential function blocks such as Teledyne RF & Microwave Phase Shifters provide reliable, high performance for RF/Microwave commercial, industrial and military systems.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
M4i.4471-x8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them.
-
product
Simultaneous Multi-Surface Test Interferometer
VeriFire MST
Simplify the complex – multiple surfaces create complex fringe patterns, the Verifire™ MST uses patented wavelength-shifting technology to acquire phase data from multiple surfaces simultaneously. Report key metrics from individual surfaces of parallel windows, transmitted wavefront, as well as precise surface-to-surface information like total thickness variation (TTV), wedge and even material inhomogeneity.
-
product
Vector Network Analyzers
One of the most important measurement tasks in radio engineering is the analysis of electrical circuits. A network analyzer is an instrument that is designed to solve this problem with high accuracy and efficiency. The circuits that can be analyzed with network analyzers have a wide range of applications ranging from simple devices such as filters and amplifiers to complex modules used in communications satellites. PLANAR specializes in the development and production of vector network analyzers that combine the capabilities of scalar network analyzers that measure not only the amplitude components of the main characteristics of the system (gain, loss, standing wave ratio, etc.), but also allow measurements of the amplitude and phase characteristics of the system .
-
product
Nonlinear Pulse-Envelope Domain
S94518B
The S94518B Nonlinear Pulse-Envelope Domain measures the vector corrected amplitude and phase of the fundamental and harmonic pulse envelopes of your DUT.
-
product
Universal Encoder Checker
Talon
Test digital Encoders (5, 12, & 24 Volts) Troubleshoot Digital Read Outs (DRO's) Count / verify Pulses Per Revolution (PPR) Adjust Encoder after cleaning or repair Test for weak or dead signal output Test for intermittent phase jitter
-
product
Single Phase Din-rail Multi-rate kWh Meter
SY 1025
Hong Kong Songyang Industrial Ltd.
Type SY1025 single phase DIN rail watt-hour meter is a kind of new style single phase electronic multi-rate watt-hour meter, energy data display adopt 7 digits wide temperature type crystal display, with many functions of multi-rate (time-of use) energy measurement, infrared carrier wave communication and RS485 serial port communication reading meter, etc.
-
product
Data Acquisition System
System 730
System 730 eliminates the errors caused by phase shift and skew between channels while maintaining state-of-the-art accuracies of +/- (0.02% FS + 2uV). Quality data acquisition systems include multi-pole filters to attenuate noise and prevent aliasing but skew and phase shift differences between channels can cause errors that eclipse the magnitude of all others.
-
product
Quantum Accelerometer
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
product
Partial Discharge Tester
GTPD-4C
GTPD-4C partial discharge comprehensive tester is the new generation of digital PD measurement and analysis instrument. The instrument has a strong ability of comprehensive analysis of partial discharge and detection of partial discharge in small signal and strong interference environment. With different accessories, it can measure and locate the partial discharge in any high voltage electrical equipment. It can realize testing the transformer partial discharge by applying the voltage on the three phases simultaneously.
-
product
Static Design Verification
ALINT-PRO
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
-
product
Portable Single Phase Power Factor Meter
Supreme Instrument Laboratories
Portable Electro-dynamometer type single phase single element Power Factor Meter laboratory type for horizontal use, housed in laminated wooden cabinet size 235 mm length x 200 mm width x 180 mm height, with detachable lid, black bakelite panel fitted with anti-parallax mirror scale, knife edge pointer, rubber footings, carrying handles, locking arrangements. The power Factor Meters are fitted with an iron shielded Electro-dynamometer type cross coil system.
-
product
Programmable Delay Line Instrument
XT-100-OEM
With the XT-100-OEM, all the capabilities and precision of the XT-100’s trombone technology can be built right into your own system. This product is intended primarily for OEM applications so you have a streamlined solution for precision phase shift or programmable delay.
-
product
RF Frequency Divider, Multiplier, & Detector Modules
Analog Devices’ broad portfolio of frequency dividers, multipliers, and detector modules offers a number of high performance solutions, with features such as ultralow phase noise and improved frequency lock time to meet the demands of modern technology. Explore our product lines and discover how they can meet your industry, market, and design needs.
-
product
Focus Control And Stabilization
Applied Scientific Instrumentation
The CRISP system is designed to maintain focus over time i.e. compensate for thermal & other factors that may cause the sample to drift out of focus over time. It also can be used to maintain a given focal point while scanning the sample in XY. If you are looking to find the optimal focal point while scanning through the sample in Z phase.
-
product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2233-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Rail Wheel Testing Using Phased Array System
ECHOMAC® PA Wheel Tester
MAC introduces two versions of Rail Wheel Testers using ECHOMAC® PA platform based on customer requirements. One is a semi-automated solution using local immersion technique. Used for tread inspection of new and/or reprofiled wheels. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread inspection. The second solution is a fully automated immersion tank. Performs tread and face inspection of rail wheels using two phased array probes simultaneously. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread and face inspection, while monitoring the backwall on the face side per EN 13262.
-
product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
product
Enlarge Environmental Chamber
REXMED REC-480
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Volt Tester
VT750LCD
The VT750LCD is a compact reliable robust automatic voltage tester up to 750V. The testers can measure and indicate the exact voltage (AC/DC), phase indication, phase rotation and continuity, RCD, and resistance via an LCD.
-
product
Phase Angle Voltmeter
PAV1010A
Measuring Vrms, inphase, quadrature, freq, ratios and phase angles. Using Discrete Fourier Transform algorithms, the PAV1010A provides capability, performance and versatility not available with traditional PAVs. Targeted at the Synchro/Resolver and LVDT/RVDT marketplace, this instrument makes measurements of Phase Angle, In-Phase, Quadrature (90° component), Fundamental and Total Vrms very straightforward. All these measurements are displayed simultaneously on a bright multifunction display.
-
product
Phase Rotation Meter
PCE-PI 1
The digital phase rotation meter PCE-PI 10 is used to determine the direction of rotation of 3-phase voltage networks. Furthermore, the phase rotation meter is able to measure voltages up to 600V AC / DC. The rotating field direction is important for machines and plants.
-
product
Multiple Audio Tracks Analysis
Multi Pack
Blue Cat's FreqAnalyst Multi plugin provide extremely smooth spectrum and frequency content analysis, the Blue Cat's StereoScope Multi analyzer let you visualize the stereo image of your audio content in details, and the Blue Cat's Oscilloscope Multi waveform viewer shows the waveform of audio signals as well as their phase relationship.
