-
Product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
-
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
Product
Function Generators
-
PGP Electronics Private Limited
PGP Electronics Function Generators are a reliable source for different waveforms. Two units, function generator and frequency counter are integrated in to one unit. The built-in frequency counter can also be used to measure the external frequency.
-
Product
LCR Digital Bridge
FD2810B
-
• Test parameter: C, R, L, Z, D, Q• Test frequency: 100Hz, 120Hz, 1kHz, 10kHz• Test level range: 0.1V, 0.3V, 1.0V• Output impedance: 30Ω, 100Ω• Slow or fast (15 times/s)• Automatic selecting, out of limit alarming• Provide the RS-232 & HANDLER interface• Accuracy: 0.1%
-
Product
Noise Source Family
346 Series
-
This series of broadband noise sources has been designed to cover the majority of measurement applications with a range of frequencies, Excess Noise Ratio (ENR) and coaxial connector types.
-
Product
EPM Series Dual-Channel Power Meter
N1914A
Power Meter
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
Product
Multimeters
METRAHIT Series
-
All multimeters measurevoltage, resistance, frequency, continuity and diode test.
-
Product
Gain-Compression Measurements
S96086B
-
The S96086B, gain compression measurements provides fast and accurate characterization of input power, output power, gain, and phase at the compression point of an amplifier, over a specified frequency and power range, with a simple setup
-
Product
Climatic Chamber
-
Wewon Environmental Chambers Co, Ltd.
Climatic chamber is designed to do high temperature & high humidity, high and low temperature, or temperature cycling test, Climatic chamber mainly used for quality checking and assessing their quality reliability and life test. ● The climatic chamber simulate a full range of temperature testing and humidity testing conditions.These chambers are designed for ease-of-use, reliability and performance and include many user-friendly features standard with your purchase for the best value in the industry. ● Climatic test chambers are able to provide rapid product temperature change rates and use varying levels of relative humidity to locate design problems prior to shipping your products, improving product quality and reliability. climatic chamber For conditioning of samples prior to testing. Climatic chamber also can be used for a variety of materials of high – low temperature alternating test. The test temperature, humidity, time can be programmed. Provides conditions of temperature form -70 degree to +150 degree and of humidity from 20% to 98%. ● This type climatic chamber use 16bit Industry-grade PLC, programmable controller to control the test temperature test, and recycle time, more excellent anti jamming, high reliability of the data. ● TEMI880 large color LCD touched screen temperature & humidity controller. Real-time display program running time, the number of segment, the remaining time, repeat frequency,can display experimental data, including the pre-set segment time, heating status, calendar time, etc; climatic chamber directly digital display. ● Climatic chambers apply controllable silicon step-less adjusting technology to adjust temperature and humidity test continuously and precisely, and without over heated as the PID adjusting function. ● The thermal insulation material between outside and inside for climatic chamber is high-quality ultra-fine glass fiber insulation cotton, good thermal insulation effectivity. Thermal insulation layer composed of flame fire PU + glass wool insulation (insulation thickness 10.0 cm)
-
Product
Industrial Multimeter
CMM-40
-
Industrial multimeter CMM-40 was designed for the purpose of measurements of AC/DC voltage, AC/DC current, resistance, capacitance, frequency (electrical and electronic), duty cycle, temperature and also for testing diodes and continuity.
-
Product
Power Dividers
-
We currently offer coaxial resistive power dividers (aka power splitters), which are inherently broadband and have excellent low frequency response (0!) albeit with poor isolation; and also Wilkinson Power dividers, aka Wilkinson Splitters. We have as connector options SMA, N, 1.95mm, & 2.92mm. Our power dividers cover DC-70Ghz. While most of our power dividers are 2-ways, we also have 3, 4, & 8 way dividers. The resistive power splitters are implemented with tiny resistors. Wilkinson splitters can be microstrip or stripline. RF Power Dividers are often lumped element, Microwave Power Dividers are often microstrip.
-
Product
6U CPCI Processor Board
CP62101
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
Product
Digital Sound Level Meter
Model KM 926
-
Kusam Electrical Industries Limited
• KM 926 designed according to the IEC 651 TYPE 2 & ANSIS1.4 TYPE 2 for sound level meter.• Instantaneous sound measure function.• Measurement Range : 30 ~ 130decibel• With two equivalent weighed sound pressure levels, A & C.• Fast & Slow dynamic characteristic modes.• AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
Product
Standard Gain Horns
-
26 dB typical gain at center frequency. Aluminium made High performance Standard Gain Horn. From 75 GHz up to 500 GHzUG-387 U/M flange. Specific gain values can be requested. We offer two Standard Gain Horn product lines that go from 75 GHz up to 500 GHz, one with high performances for the most demanding of lab applications and the other with reduced prices and sufficient quality for the majority of SGH applications. Anteral makes sure that each client can have the best SGH for their particular needs.
-
Product
Low Noise Triple Band Voltage Controlled Oscillator
-
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
Product
QDRII/DDRII/ QDRII+/DDRII+ SRAM
-
DDR II / II+ (Double Data Rate) SRAMs and QDR^(TM) II / II+ (Quad Data Rate) SRAMs are the ideal memory devices for next generation networking and communications systems. These ultra-fast devices can support high bandwidth systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
Frequency Meter
Pointer Type
-
*Frequency Meters pointer type with inbuilt transducer are available in size 72 X 72, 96 X 96 mm suitable for 110V, 230V & 440V AC*Scale 45-50-55 Hz.*Model : SF-72, SF-96.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 12.4 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-780B-513-E
Relay
The 40-780B-513-E (PXI) and 42-780B-513-E (PXIe) are triple failsafe SPDT 12.4 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Fuel Flow and Torque Converter
Model 44SM1
-
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
Product
Fibre-Coaxial DOCSIS Analyzer
CABLERANGER
-
DOCSIS 3.0 analyzers for hybrid Fibre-Coaxial networks CABLE RANGER from PROMAX provide all the required measurements to install and carry the network maintenance of those hybrid networks using fiber optics and coaxial cables at the physical layer. The operating frequency range spans from 5 Mhz to 1700 Mhz, thus fulfilling DOCSIS 3.0 and 3.1 requirements.
-
Product
RPM Indicator
CS2-RL
-
CS2-RL RPM Indicator has been designed with high accuracy measurement, display and communication of pulse (Frequency).The innovation feature is auto-range input from 0.01Hz~ 100KHz (option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of testing and machinery control applications.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5GHz, 75Ω, 1.6/5.6, Remote Mount
40-780B-753-E
Relay
The 40-780B-753-E (PXI) and 42-780B-753-E (PXIe) are triple SPDT 2.5GHz 75Ω unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
EPM and EPM-P Series Power Meter
-
The EPM and EPM-P Series provides high-performance, programmable power meters for CW, average and peak power measurements. EPM Series: measure average power over a range -70 dBm to +44 dBm, and over frequency range 9 kHz to 110 GHzEPM-P Series: measure peak, average and time-gated power over -65 dBm to +20 dBm, to 18 GHz using E932XA power sensors. It provides complete pulse and statistical analysis with PC software via the GPIB or RS232
-
Product
900 Hz to 120 GHz PNA MM-Wave System
N5291A
-
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Compact Eddy Current Sensor System
eddyNCDT 3005
-
Compact and robust design. - Temperature compensation up to 180C. High precision measurement accuracy. High frequency response. Sensor for ferro- and non-ferromagnetic targets. Easy to use (plug & play). Perfect for machine integration.
-
Product
Digital Multimeters
-
The Gamma series consists of digital multimeters. They are capable of measuring electrical parameters like current, voltage, frequency, temperature, resistance, diode test and continuity test of the circuit respectively.
-
Product
Time Frequency Analysis Function
OS-0527
-
This function can evaluate transient phenomena that were difficult to capture by FFT analysis, and display clearly time change of the frequency component while maintaining its frequency resolution . The OS-0527 is equipped with STFT (Short Time Fourier Transform) and Wavelet transform.
-
Product
Custom Test Connectors and Sockets
-
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
Product
Multiple Signal Generator
-
1. Two Signal Output Ports2. Frequency Range:10 Hz ~ 100 kHz and 1 kHz ~ 15 MHz3. Output Waveforms:Sine, Triangle, Square,TTL Pulse, AM, FM4. Amplitude:10 Vpp(Max)5. Built-in LCD CountersDC Power Supply：1. Triple Outputs (One Variable, two Fixed Output)2. Constant Voltage Operation3. Low Ripple and Noise4. Built-in 3-Digit Voltage Indicator5. Overload Protect6. Overload Buzzer Indicator
-
Product
Spectrum Analyzer Extension Modules
SAX
-
Virginia Diodes, Inc. (VDI) Spectrum Analyzer Extension (SAX) modules provide high performance broadband down-conversion and frequency extension of microwave spectrum analyzers into the THz range
