RF Chambers
isolate and supress RF waves.
See Also: Chambers, TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers, RF Enclosures
-
product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
product
PXI-2593, 500 MHz, 50 Ω PXI RF Multiplexer Switch Module
778793-01
500 MHz, 50 Ω PXI RF Multiplexer Switch Module—The PXI‑2593 can be programmatically configured as unterminated multiplexers, externally terminated multiplexers, or dimensionally flexible sparse matrices.
-
product
PXI-2545, 2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-45
2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2545 is an RF signal multiplexer switch module. The internal termination of the PXI‑2545, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in RF applications where such reflections can damage the source. The module also provides excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
RF / MW switch
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
product
RF Synthesiser
The Laplace Synthesisers cover both conducted and radiated RF immunity test requirements. The frequency coverage extends from 100KHz to 230MHz for conducted tests and 30MHz - 6GHz for radiated tests. They are all controlled from the users PC via a USB link, and powerful Windows software is included to enable the user to control all the parameters of the test, to monitor the test in progress, and to view the results.
-
product
6U VPX Direct RF Processing System
VP460
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
product
PXI Single RF Attenuator 63dB in 1dB steps
41-180-021
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module
-
product
RF Test Spectrum Measurements over CPRI
Integris 3000
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
product
RF Power Amplifiers
Specially selected products to complement our ultrasound measurement equipment.
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Salt Spray Test Chamber
Salt water spraying/corrosive resistant machine are specialized to test the performance of the products for its surfaces of various materials after treatment of corrosive protection by means of painting, coating, galvanizing, anodizing and of lubricant.
-
product
Wattchman RF Station Monitor/Alarm Systems
81080 Series
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
-
product
RF Routing Switches
Quintech Electronics and Communications Inc.
RF Monitoring and Routing Switch.
-
product
PXI Quad 4 to 1 RF Miltiplexer 6GHz 50 Ohm SMA Terminated
40-882-004
A 50 Ohm 4 to 1 6GHz PXI RF multiplexer available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules. This PXI multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40-882 MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, SMB
40-877A-002
The 40-877A-002 (PXI) and 42-877A-002 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 75Ω, SMB
40-830A-006
The 40-830A-006 (PXI) and 42-830A-006 (PXIe) are 75Ω RF switches with 6 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
Cytogenetic Drying Chamber
CDS-5
Developed in cooperation with Mayo Clinic, Thermotron's Cytogenetic Drying Chamberthe CDS-5was specifically designed for conducting cytogenetic slide drying tests during harvest of in situ and non-in situ grown cultures. The CDS-5 provides the optimum controlled temperature and humidity environment required to achieve ideal chromosome spreading results. As evidenced in research conducted by the Cytogenetics Laboratory at Mayo Clinic, the CDS-5 facilitates reliable and repeatable chromosome spreading. The use of an environmentally controlled drying chamber is a practical and cost effective way of achieving ideal chromosome spreading in a routine and highly consistent manner. Favorable chromosome spreading results can be obtained for both in situ and non-in situ cultures including PHA stimulated lymphocytes, bone marrow, amniocytes, and fibroblast.
-
product
RF Power Splitter, Combiner, Divider
PD2430
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (28 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) Low PIM
-
product
PXI-2557, 2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-57
2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2557 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2557 makes it ideal for test systems that require the switching of a large number of video RF signals, such as switching several video tuners under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
IP X1, X2 Chamber - Drip/IP Test Chamber
The drip box testing chambers from Weiber are rain test machines used for testing the outer protection of signal devices, external lighting equipments and car lamps etc. The equipment finds widespread usage in electronics industry and automotive and aerospace industries and is commonly employed for quality testing of products. The test chamber comprises of the guiding upright column, a drip mold, a rotating sample table with adjustable speed and a level meter to allow observation of the level in the drip mold. The equipment uses high quality construction materials for a sturdy construction and is designed for safe and reliable operation. The guiding upright column is made up of high-quality, plastic coated square steel pipe, whereas the drip mold is made up of high-quality stainless steel finish plate undergoing knurling.
-
product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 57891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
RF & Microwave PXI Switch Modules
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
product
Altitude Chambers
ESPEC can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are: Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions.
-
product
Salt Fog Chambers
SCCH
Seamless, oven-cured vinyl lining for maximum service life and corrosion resistanceClear acrylic cover optimizes test observation. Individual temperature display for Dry Bulb, Wet bulb and Humidifying tower. Internally-baffled Opti-fog® tower for uniform atmosphere and efficient solution usage.Air Flow Meter - Convenient indication of Opti-fog® performance without waiting hours for collection rates.Level-Matic® Reservoir Assembly Automatically maintains proper solution levels to Opti-fog® and Humidifying Tower. Standard operating temperature of ambient to 120°F/49°C (higher temps optional)Fully tested and certified prior to shipment.
-
product
RF Electronic Calibration Module (ECal), DC To 13.5 GHz, 4-ports
N4431D
The Keysight N4431D RF electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4431D is a precision 4-ports ECal module that supports multiple selection of connectors like Type-N, 3.5 mm, 7-16 and 4.3-10 connectors and can be mixed up to 13.5 GHz. Select either female-female, male-male, or female-male connectors.
-
product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector
40-728-002
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
