Monitors
Continually examine for quality.
-
product
Structural Health Monitoring System
SHM
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
product
3 DB 180 Degree Hybrid Couplers
KRYTAR's 180 Degree Hybrid Couplers offer wide frequency coverage in single, compact packages which provide low insertion loss, high directivity and tight coupling. These hybrid couplers offer simple solutions in many applications within those frequency bands including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted situations the compact size of these KRYTAR couplers are ideal. These couplers can be also be manufactured to meet military specifications.
-
product
8U 21 Slot VME64/64X Enhanced Crate
VME8100
short circuit protection, Over / Undervoltage protection, Over temperature protection. Remote monitoring and control take place through CAN bus, Ethernet, USB and RS232 interfaces. The crates are also SBC controlled via graphic OLED Display, provides Automatic Daisy Chain and supports Chained Block Transfers (CBLT). User-friendly control software completes the VME 8100 features. The Unit is powered by 92 ÷264 Vac, 50 ÷ 60 Hz, power factor 0.98% (230VAC).
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
Digital "A" Flow Controller for High Flow
HFM-D-306A / HFC-D-308A
Mass flow techniques provide RELIABLE, REPEATABLE AND ACCURATE gas flow rate measurements.HFM-D-306A/HFC-D-308A mass flow instruments have flow ranges from 0-2500 slm to 0-10000 slm; provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available. Available with a variety of elastomer seals for maximum flexibility.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
-
product
ForceTest Force Measuring Software
AMETEK Sensors, Test & Calibration
The ForceTest software interfaces directly with your digital force gauge enabling you to automatically capture tests and graphs on a personal computer. Test results and graph can be monitored directly on the live screen in real time while the test is being performed.
-
product
Smart Touch Computer Series
ADLINK’s Smart Touch Computer (STC) series is ideal for human–machine interface (HMI) applications in food and beverage, pulp and paper, textile, printing, word processing, and other industries. These standalone full-function panel PCs are designed for optimized production control and system monitoring, offering scalable performance, customizability, and I/O expansion. With an industrial-grade, robust construction, and slim design, The all-in-one STC Series is designed for extended operation, allowing manufacturers to obtain time-sensitive sensor data and easily monitor and control manufacturing processes.
-
product
Programmable Industrial USB 3.0 Hub (8 Ports)
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
product
Mixed Signal Oscilloscopes
The design, validation, and manufacturing of modern electronics necessitate the measurement of both analog and digital signals. Mixed signal oscilloscopes enable the simultaneous, time correlated observations and analysis of analog with digital (logic) signals, to establish causal relationships between the various areas of a device's electronics. They are purpose built tools for troubleshooting electrical anomalies, measuring parametric values, and monitoring cause and effect relationships between signals.
-
product
NTSC/PAL Color Bar Generator
CBG360
The CBG360 is designed to provide an accurate and affordable signal source for system testing. It also provides the necessary components for aligning color monitors to the proper brightness, color and hue.
-
product
Multiport Coaxial Switch, DC to 4 GHz, SP4T
87104A
The Keysight 87104A multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87104A terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
product
Digital Ethernet Power Meters
FU2200A
Beijing GFUVE Electronics Co.,Ltd.
Digital Ethernet power meter with data logger is a three-phase multifunction power and energy meter manufactured by GFUVE. It provides excellent value for monitoring power and energy management systems. It may be used as data gathering devices for intelligent power distribution or plant automation systems. All monitored data is available via a standard digital RS485 communication port, which is based on the Modbus RTU protocol.
-
product
Resonance Dip Meter
NRM-2
National RF’s Resonance Dip Meter is a test instrument used to determine the resonant frequency of a tuned circuit or resonant network, such as an antenna system. In addition, the unit may function as an RF detector, or a secondary frequency source. The instrument is analogous to the older vacuum tube “grid dip meter,” once popular in every electronic laboratory or radio station. Unique to this updated version is a buffered output that may drive a digital frequency counter for exact measurement of resonant frequency, or connected to an oscilloscope to be used as an RF detector and waveform/modulation monitor.
-
product
Measuring And Testing Devices
Delphin develops, produces and sells measuring, testing and automation devices for applications in the fields of measurement, test stand and monitoring. Various series of devices, for different tasks enable our customers to find the right solution for your task quickly and efficiently.
-
product
Master Reference Generator
Mentor
Precision Time Protocol IEEE-1588 PTP grandmaster• Multiple video and audio formats in one box• Simultaneous 525/625 and HD Tri Level Sync outputs• Highly accurate GPS reference for synchronisation and timecode• Vector web-browser setup and monitoring tool• Redundant PSU option• Add upgrades and options without return to factory• Generates synchronised audio and video• Redundant units with changeover• 4K test pattern ready (future upgrade)
-
product
Multiprotocol Serial Boards
104-COM-8SM-T
This is an eight-, four-, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports RS-232, RS-422 or RS-485 communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors. Common applications include POS, gaming systems, machine monitoring, military and high-density networking.Type 16780 UARTS are used as the asynchronous communication elements.
-
product
Sound Power Measurement
Dewesoft sound power measurement solution merges the best of both worlds: widely established sound power measurements with familiar, distinctive user interface and industry unmatched adaptability. Rate and compare different noise sources with ease and exactness while simultaneously monitor any number of additional parameters.
-
product
Software
Blaze
Blaze software is the ideal data analysis and reporting tool for Industrial Hygiene and Safety professionals. From simple, concise compliance reports to powerful detailed data presentations, Blaze excels in supporting various exposure sampling methods and interfaces with the Spark family of personal Noise Dosimeters, the SoundTrack LxT Sound Level Meter and the HVM100 Human Vibration Meter. From instrument setup to presentation-ready reports to exposure record management, Blaze makes noise and vibration exposure monitoring more convenient and productive
-
product
Online UV Analyzers
Accurately monitor performance of UV filtration systems with online UV analyzers. Our online UV analyzers use UV254 technology to provide accurate water quality tests. Help ensure safe municipal wastewater with trusted wastewater UV analyzers you can count on.
-
product
Medium Thermal Shock Chambers
TSD-100
The TSD-100 has our popular touch-screen controller, but with a new feature called Specimen Temperature Trigger (STT). This STT function actively monitors the temperature of the product and only advances the program to the next step once the product has reached the desired temperature. The STT dynamically reduces the overall testing time by adjusting the soak period according to how much product is being tested.
-
product
Network Analysis
Network development solutions come in different formats to support the variety of applications, such as network analysis or node emulation. Network analysis is crucial throughout the development of any networked system or module. The ability to capture, view, and record messages allows monitoring of bus integrity or troubleshooting functionality of the modules on the network. Whether developing a concept or preparing for production, access to the network is essential. Node simulation can be done with software, such as ATI's CANLab Software, or hardware components, possibly CANverter, depending on whether the environment is on the bench or in the vehicle.
-
product
Fault Recording Monitors
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
product
Laser energy meter with high dynamic range
PM 200
In the past laser energy meters often required a whole selection of pyroelectric detectors for measuring different energies. From this point of view the PM 200 is a very modest instrument. A single detector enables monitoring of energies from the detection limit at 3 ?J up to highest energies of 200 mJ. The active sensor area with an aperture diameter of 34 mm ensures simple and reliable alignment for the detection of large beam profiles.?
-
product
Broadcast TV Multiviewer Monitoring System
IMS120
The Mividi IMS120 is a broadcast transport stream monitoring system for viewing video and audio services, analyzing transport streams, logging errors, generating alarms, and recording stream. The IMS120 was developed to automate monitoring and error diagnosis at digital head-ends for broadcasters, MSOs, Telcos and online streaming video providers. It is a single Windows based system that can complete tasks previously done by several different pieces of equipment. It will pay for itself in manpower savings over a short period of time.
-
product
PCIe Basic Protocol Tx and Bus Monitor
Sy629PCIe-BPM
The Sy629PCIe-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
product
Isolated Watchdog Board
APCI-035
The board ADDIMULTI APCI-035 is equipped with 4 watchdogs allowing the simultaneous monitoring of multiple processes. Watchdog N? 1 works with 2 alarm levels and can be set to 1 of 4 different time bases (µs, ms, s, min). Level 1 alarms the PC cntrol and/or the monitored device. Level 2 resets the PC and/or the monitored device after a defined time. The alarm control can be accessed through 1 trigger channel and 4 different time bases.
-
product
Fieldbus Systems
ADDI-DATA offers fieldbus systems for Ethernet and EtherCAT. The Ethernet Systems can be upgraded with an additional Wi-Fi interface for parameter settings and easy monitoring.
-
product
Software-only USB Protocol Analyzer
USBTrace
USBTrace is an easy to use and powerful USB analyzer. USBTrace can monitor USB transactions at host controllers, hubs and devices. This is a 100% software product.
-
product
C Series Current Input Module
The C Series Current Input Module features programmable input ranges, variable connectivity options, and built-in noise rejection. You can also choose from options with built-in anti-aliasing filters or high-channel density to reduce the number of modules needed. The C Series Current Input Module supports safety features, certifications, input ranges, overvoltage ranges, and connectivity for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs). The C Series Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
