Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
UL 1410 Coin Probe
CX-121
Shenzhen Chuangxin Instruments Co., Ltd.
Four probes in one! Used to determine accessibility to shock hazards in many household and audio/video products, including Standards UL 1410 and UL 6500. Made entirely of nickel-plated steel.
-
product
Display-Only Dynamometer Testing Instrument
DynTek-PC
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
product
PCI 2 Amp Multiplexer, Single 32-Channel, 2-Pole
50-635A-002
The 50-635A-002 is a single 32-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - 3U VPX
Model 5953
- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6003 QuartzXM- Model 6003 unique QuartzXM eXpress module enables migration to other form factorsPentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products VideoLive Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boardsPipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoCSynchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPXPlease refer to the product datasheet for Installed FPGA IP Module details
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL
The 72-7770 CAL from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) Bead Probe
BTP-1F-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Automotive-grade Diodes
ST's portfolio of automotive diodes is qualified to the AEC-Q101 standard and is intended for DC-DC converters used in numerous automotive functions. Most of these dedicated diodes are guaranteed in operation at junction temperatures as low as -40 °C and as high as +175 °C. The automotive-grade diodes belong to our STPOWER family.
-
product
Standard Capacitor
• 3 terminal design • SF-6 Gas filled • 15kV, 33kV & 50kV models available
-
product
FC Patch Cord
FY6
Fiberyo provides a full line of fiber optic cable assemblies, covering SC, FC, ST, Din, D4, E-2000, SMA, LC, MU, MPO, MT-RJ, with PC(physical contact), UPC(Ultra physical contact), APC(Angled physical contact) polishing, using quality Fiberyo connector components, they are designed to comply with industry standards for optical, mechanical and environmental performance.
-
product
SINE M-14 Sinusoidal Array
The Sinusoidal Array SINE M-14 was designed for various electro-optical applications, particularly where a small array is needed to fit into the frame. It can fit into an 18mm diameter circle or into a standard 35mm motion picture frame.The lines in the SINE M-14 lie perpendicular to the length of the film. In addition, the pattern is available on a wider film (without perforations) cemented between glass (TM-G options) both the .6 (-60) and .8 (-80) modulations.
-
product
Nitrate Ion and Nitrate-Nitrogen Concentrations Pocket Water Meter
LAQUAtwin NO3-11C/NO3-11S/NO3-11
The only pocket meter that directly measures nitrate ion and nirate-nitrogen concentrations in 0.3ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Standard 1.08 (31.00) - 4.00 (114.00) Long Travel Bead Probe
BPLT-25HF-4
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
product
Transformer Test Panel/ Setup
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
product
Design Verification Editor Checker for SV/UVM
DVinsight
DVinsight-Pro is a Integrated Development Environment (IDE) for creation of Universal Verification Methodology (UVM) based System Verilog (SV) Design Verification (DV) code. Design & Verification Engineers can create correct by construction DV code because DVinsight-Pro is a design verification editor checker that provides helpful insight into user code and ensures compliance with UVM best practices while adhering to established standards.
-
product
BRIC™ - Large PXI Matrix Modules
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
product
SparkFun Load Sensor Combinator
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
product
AHD Camera
Sylo Vision Technology Co., Limited
s an analog high definition closed-circuit television video surveillance standard that uses coax cable to transmit HD video from security cameras to DVRs.
-
product
Dytronic Primary Transfer Ultra Stable Standard
RD-22 Ultra
The RD-22 Dytronic Primary Transfer Ultra Stable Standard represents the state-of-the-art technology in a commercially available AC transfer reference. The Ultra Stable RD-22 is a variant of the RD-22 Primary Transfer Standard that has been optimized for 120/240 V @ 5A operation to provide optimum stability. In a stable test environment, repeatability for a 10-second test of ±0.6 µWh/VAh is attained at 120 V and 240 V at 5A inputs with a 95% confidence interval. A typical experimental 2 repeatability of less than ±0.25 µWh/VAh is achieved. In a stable test environment, a reproducibility of ±2 µWh/VAh over a five-day interval is attained at 120 V and 240 V at 5A inputs with 95% confidence interval.
-
product
USB 2.0 Protocol Analyzer
Mercury T2
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
product
Standard 0.50 (14.00) - 2.00 (57.00) Non Replaceable General Purpose Probe
A-A-S-C
Current Rating (Amps): 2Average DC Resistance lower than (mOhm): 30Test Center (mil): 39Test Center (mm): 1.00Full Travel (mil): 30Full Travel (mm): 0.76Recommended Travel (mil): 20Recommended Travel (mm): 0.51Overall Length (mil): 310Overall Length (mm): 7.87Rec. Mounting Hole Size (mil): 31.5Rec. Mounting Hole Size (mm): 0.80Recommended Drill Size: #68 or 0.79 mm
-
product
Standard 0.39 (11.00) - 1.39 (39.00) Non Replaceable General Purpose Probe
MEP-20G
Current Rating (Amps): 2Average Probe Resistance (mOhm): 50Test Center (mil): 25Test Center (mm): 0.635Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 750Overall Length (mm): 19.05Rec. Mounting Hole Size (mil): 20.5Rec. Mounting Hole Size (mm): 0.52Rec. Mounting Hole Remark: 20.5 to 21.5 mil / 0.52 to 0.55 mmRecommended Drill Size: #75 or 0.52 mm
-
product
Digital Pattern Generators
DPG
Active Technologies Digital Pattern Generators also known as DPG, allow digital stimuli generation to stimulate digital designs, providing the capability to emulate standard serial or parallel bus transactions or custom digital interfaces, for system or device debugging and characterization.
-
product
Scienlab Regenerative DC Emulator
SL1800A Series
Keysight's SL1800A Scienlab Regenerative DC Emulator - High-Power Series enables users to emulate the large batteries in electric vehicles. The bidirectional power flow allows emulation of both power sourcing applications, such as traction inverter test, as well as power-absorbing (sinking) applications, such as EV charging. Being regenerative, the power absorbed is delivered back to the grid, saving on energy and cooling costs. The SL1800A Series is fully integrated with the SL1040A Scienlab Charging Discovery System. The SL1093A Scienlab Charging Discover Software fully automates DC charging applications to many different test standards. With bi-directionality, integrated DC voltage and current controllers, high dynamics, and its regenerative energy feedback capacity, the Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Transmissive Rotary Codewheel
HUBDISK-1
US Digital offers a wide variety of standard hub / disk assemblies (optical encoder disks attached to an aluminum hub) to aid with mounting on a shaft. Encoder disks may also be ordered as a stand alone item (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable.
-
product
Single Board Computers
SBC
*This section contains a wide range of Single Board Computers (SBC) available in many form factors: EPIC, EBX, and much more. *These embedded Single Board Computers come in standard form factors in compact sizes with rich I/O, high flexibility, easy expansion capabilities and extended temperature options.
-
product
Digital Solutions
Digital ST60 Dual Thermopile (Preliminary)
A two channel silicon- based thermopile in a TO-5 package that includes integrated electronics which incorporate an industry standard digital SMBus interface. Each small active area size is 0.61mm x 0.61mm.
-
product
Rack Mount Kit Solutions For The E36100B Series
E36110A
The Keysight E36110A rackmount kit is designed to secure 1 - 4 units of E36100B Series DC power supplies horizontally in a standard 19-inch rack cabinet. They are designed to fit in two rack-units (2U) of space.
-
product
Standard 1.53 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-72J-4
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
High Precision Angular Position, Calibration and Geometry Inspection
GeoOrdinate
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The GeoOrdinate has been designed specifically for the inspection of large and heavy components and is fully compatible with any shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
