Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Network Analyzer, Tester, LCD
72-8495
-
Compact 2-in-1 unit provides standard digital multimeter functions, as well as pin configurations on network and voice cables. Dual pinout indicator provides sequential verification of each pin on a network cable, and the included remote terminator allows testing of cables which are already installed. Digital multimeter measures AC/DC volts and amps, resistance and diodes, and provides audible continuity test.
-
Product
Standard 1.00 (28.00) - 2.30 (65.00) Non Replaceable General Purpose Probe
P2532-1
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 156Test Center (mm): 3.96Full Travel (mil): 139Full Travel (mm): 3.53Recommended Travel (mil): 93Recommended Travel (mm): 2.36Overall Length (mil): 812Overall Length (mm): 20.62Rec. Mounting Hole Size (mil): 94.5Rec. Mounting Hole Size (mm): 2.40Recommended Drill Size: #41 or 2.40 mm
-
Product
Standard Voltage 37-Pin D-Type Connector & Cable Accessories
-
The Standard Voltage 37-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution.Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Product
pH Pocket Water Quality Meter
LAQUAtwin pH-33
-
The only pocket meter that directly measures pH in 0.1ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
Corona Effect Camera
CoroCAM 8 UAV
-
*High-sensitivity UV detector, which can detect UVc light at 2.05×10-18 Watt/cm2, this allows detection of the smallest corona discharges.*9Hz (or 25Hz optional) IR radiometric camera module*Control of a limited number of camera functions from a standard RC controller using PWM or SBUS.*Remote control of all camera functions from the laptop via an Ethernet link.*Soft sync or staggered zoom of the 3 channel cameras. The IR and UV channels are digitally zoomed in, which is visible...optically zoomed in to the minimum FOV, and then digitally zoomed out.
-
Product
ISO/ANSI Compliance
-
The ANSI and ISO/IEC standard for the C Programming Language specifies that there are two forms of conforming compiler implementations: hosted and freestanding.
-
Product
Sound and Velocity Data
MIDAS SVX2
-
The MIDAS SVX2 is the standard for the offshore Oil & Gas industry. Recognising the conflict faced by users requiring the superior Sound Velocity data from an SVP, but still needing the Salinity and Density data from a CTD, the Midas SVX2 combines both technologies to give the best of both worlds
-
Product
PD Coupler
-
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
Product
Passive Probes
-
Passive voltage probes ship standard with most oscilloscopes and provide a low cost, general purpose probing solution. Generally, these probes lack the performance of an active voltage probe but provide the ruggedness and wide dynamic range suitable for visualizing signals over a broad range of applications. Tektronix has released a new class of passive probes that redefine performance in the passive probe product category.
-
Product
Capacitors
-
Ceramic Disc Capacitors have long been the standard of the industry, and offer the broadest selection of available ceramic formulations and package sizes. With a capacitance range of 1 pF to .082 mF, CTS capacitors offer a variety of TC materials and tolerances. The range of temperature characteristics available makes the products suitable for the ultra-stable requirements of tuned circuits to the general purpose needs for coupling and bypassing. Encapsulated with a hard, bright polymeric coating, these capacitors are formulated to provide mechanical protection under normal environmental conditions.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
Product
Standard 3.74 (106.00) - 14.35 (407.00) High Frequency Probe
K-50B-QG-75R
High Frequency Probe
Nominal Impedance (Ohms): 50Bandwidth @ -1dB (GHz): 12.00Return Loss @ -20dB (GHz): 3.00Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 1,637Overall Length (mm): 41.58
-
Product
Alveograph Test Series
-
The Alveolab and AlveoPC analyzers are internationally recognized as the essential and standard tool used to measure rheological properties (tenacity, extensibility, elasticity, and baking strength) of dough, and therefore baking performance of flours used for baked goods, noodles, biscuits, etc.
-
Product
Silicon Diodes
DT-670 Series
-
DT-670 Series silicon diodes offer better accuracy over a wider temperature range than any previously marketed silicon diodes. Conforming to the Curve DT-670 standard voltage versus temperature response curve, sensors within the DT-670 series are interchangeable and, for many applications, do not require individual calibration. DT-670 sensors in the SD package are available in four tolerance bands—three for general cryogenic use across the 1.4 K to 500 K temperature range and one that offers superior accuracy for applications from 30 K to room temperature. DT-670 sensors also come in a seventh tolerance band, B and E, which are available only as bare die. For applications requiring greater accuracy, DT-670-SD diodes are available with calibration across the full 1.4 K to 500 K temperature range.
-
Product
Insulating Oil Tester
OTSA series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Tests as per international standards• Auto / Manual mode• 100 test result storage capacity• Large LCD display• Built in printer• User Friendly RS 232 Interface• Safety protection• Accurate performance
-
Product
Hermetic Solid-State Battery Cell
BHC1
-
Gas-tight hermetic battery cell with electrical feedthroughs for solid-state battery testing. Standard size 86 × 98.5 mm with 200 mm wire length, compatible with standard battery molds and customizable for research applications.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Standard 1.55 (44.00) - 3.20 (91.00) General Purpose Probe
HPA-50G
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 590Overall Length (mm): 14.99
-
Product
Standard VXI Module Shield Kits Without Address Switch Opening
-
* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Same design described above but without the address switch opening.* Complimentary layout support includes PCB design template and CAD layout files.
-
Product
Performance AC Sources/Analyzers
6800 Series
-
Accurately analyze your AC power environment with integrated waveform generation and harmonic capabilitiesIncrease your productivity with extensive built-in power measurement capabilitiesLower your cost of ownership with global support & the longest standard warranty in the industry
-
Product
Battery Extra Load Units
BXL Series
-
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
Product
Water Quality Products
-
When you need to perform critical water testing, look to us for an extensive selection of electrochemical meters, controllers, probes, electrodes, test kits, buffers, and standards. Our field and laboratory instrumentation include water analysis instruments for dissolved oxygen, temperature, pH, conductivity, salinity, and turbidity.
-
Product
Full Band Down-Converters
STC-20-10-S1
-
Full band down-converters are designed to convert high frequency millimeterwave signals down to the baseband at 10 MHz to 1.6 GHz. These down-converters deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade components, such as multipliers, amplifiers, filters, isolators, and more. The below standard offering covers the frequency range of 26.5 to 170 GHz and delivers a typical LO power of 3 dBm and conversion gain of 20 dB. The down-converters provide low harmonic levels and excellent gain flatness, making them ideal for test instrumentation applications. Specifications other than those listed below are available upon request.
-
Product
Multicore Universal Solderability Tester
MUST System 3
-
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
Product
1GHz EMC Emissions Analyser
SA1002
-
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
Product
Peripheral Boards
-
Advantech CPCI solution includes GPU, Ethernet, storage blades, and AC/DC power modules that comply with industry standards for broad compatibility.
-
Product
Ultrafast Transient Absorption Spectrometer
Harpia-TA
-
The transient absorption spectrometer HARPIA offers a sleek and compact design together with intuitive user experience and easy day-to-day maintenance meeting the needs of today's scientific world. Adhering to the standards raised by the OPRHEUS line of devices, the entire spectroscopic system is contained in a single monolithic aluminum casing that inherently ensures excellent optical stability and minimal optical path for the interacting beams. HARPIA can be easily integrated with both PHAROS / ORPHEUS and Ti:Sa / TOPAS laser systems. HARPIA features market leading characteristics such as 10-5 resolvable signals along with other unique properties such as the ability to work at high repetition rates (up to 1 MHz) when used with PHAROS / ORPHEUS system. High repetition rate allows measuring transient absorption dynamics while exciting the samples with extremely low pulse energies up to several nanojoules.
-
Product
CMP Mechanical Kits (230x135mm)
230199 – CMP-240-HP
-
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
Product
Ozone Test Chamber
EKT-2001OZ-HCLSX
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
PXI 2 Amp MUX, Dual 8-Channel 2-Pole
40-635-106
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
