Radar Test
-
Product
Water Testing Kits
-
Omega's Water Testing Kits monitor water quality in any commerical, residential, or industrial application. Rain and snow gauges are available for accurate measurement for Meteroligists
-
Product
MMIs for Test and System Integration
-
Laying out a custom PCB is too time consuming and costly for most rush projects. Pulse Research Lab has developed Mini Modular Instruments ™ to provide cost effective solutions to the most common engineering challenges.
-
Product
Test House Services
-
Microtest provides complete test house services in a clear room equipped with the state of the art handler and wafer probing system using its own innovative ATE.The test house operates in hot, cold and room temperature for both production and characterization test.Innovative reliability system for Burn In and HTOL ServicesStatistical analysis is performed for digital and mixed-signal devices.Microtest Pacific Test house is located in Malacca (Malaysia).
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Test Receiver
FSWT
-
The R&S®FSWT is the right tool for detecting compromising emanations. With two equivalent, switchable RF inputs, up to 500 MHz measurement and analysis bandwidth and two analog outputs for video voltage and demodulators, the R&S®FSWT fits perfectly into typical test setups and easily replaces older instruments.
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
Test Hardware
TTPSimulate PCI
-
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
Product
Windows Configuration and Testing Software
Kickdrive
-
fullmo Kickdrive is a Windows configuration and testing software for CAN/CANopen networks, CAN/CANopen Position Drives and other motion-oriented applications in automation industry.
-
Product
MEMS Test System Development
-
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
Product
Test and Analysis
-
ESDEMC Technology will calibrate; the Contact Mode ESD current waveform and tip voltage to 4 GHz and 30 kV, the frequency response of ESD Target & Adapter Line to 4 GHz, and the DC Resistance
-
Product
Measuring and Testing Equipment
-
Bott's measuring and testing equipment offers a multitude of advantages, making it attractive for a wide range of applications. Its modular and scalable design allows for flexible use – from individual workstations to fully integrated, automated test lines. It operates safely and in accordance with standards, complying with all relevant safety and industry standards such as DIN VDE and IEC, which makes it particularly reliable in sensitive application areas.
-
Product
Software Testing Services
-
Our test offerings include TCoE, Testing on Cloud, Entererprise Mobility Testing, Big Data Testing, Functional, Automation, Security and Performance Testing services. Our workforce is equally distributed between NA & India with a vision to be your local partner. Cigniti''''''''s SMART Tools and Cloud Enabled test labs provide cost effective solutions with early Return on Investments. Cigniti is rated at CMMI SVC V1.3 Maturity Level 3 and is an ISO 27001:2005 certified organization.
-
Product
AC Resonant Test System
-
Yangzhou Power Electric Co., Ltd
Testing of certain apparatus requires much high voltage or current that a straight AC test system is not sufficient. Thus resonant test reactor with a variable core is needed. The main advantage of such test systems is lower input power and larger output power. The resonant test system is designed to compensate capacitance in the testing circuit precisely by tuning inductance of the test system. AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
EMI and EMC Compliance Testing
-
Compatible Electronics has evolved into one of the biggest and most experienced testing and consulting companies in California. All this experience has made us keenly aware of your EMC/EMI needs.
-
Product
Transportation Bounce Test System
KRD51 series
-
Bounce testing simulates the constant loose cargo state during truck transport. Often times, containers carrying military and civilian hardware (such as: medical supplies, electronics, weaponry, communication devices) travel for extended periods of time and must be transported off-road. All of these items must maintain functionality upon arrival at their destinations.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Test Fingers & Probes
-
Test Fingers and Probes are used in most standards to check accessibility to moving parts or hazardous live parts. They comes in many forms, such as test fingers, test rods, test balls etc.
-
Product
Fiber Optic Test Kit
KI-TK081
-
Small single mode fiber optic test kit for low to medium test volume on SM systems. A fiber optic power meter and light source in a padded zip case.
-
Product
Solar Radiation (Sunshine) Test
-
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.
-
-
Product
AC DC Test Equipment
-
The products impress with a variety of technical features: TFT display, Ethernet interface, automatic test sequence to a fully electronic generator for even faster and more accurate tests. Our safety testers can be used both stand-alone without a PC as well as integrate with existing systems.
-
Product
Xenon Test Chambers
-
Weice Testing Instrument Co.,Ltd.
Weice Xenon Test Chambers (Xenon Arc Test Chambers) are used to induce property changes associated with the effects of sunlight, moisture, and heat. The property changes include cracking, color fading and yellowing could be simulated just in few days and weeks.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
Thickness Measurement Testing
DRK3011B
-
Shandong Drick Instruments Co., Ltd.
It is used for the durability test of children's mattress surface rolling and the test of the height of the cushion surface.
-
Product
Pneumatic Test Pump Kit
700HPPK
-
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
Product
Battery Testing Chambers
ET-SERIES
-
These Chambers are designed and manufactured to meet various types of battery testing requirements of its customers by keeping all safety options in mind against any harmful explosions or ignitions and user safety while testing these batteries for environmental stress conditions
-
Product
Fault Injection and White-Box Testing
VectorCAST/Probe
-
VectorCAST/Probe is integrated with the full family of VectorCAST tools allowing probes to be inserted during Unit, Integration, or System Testing. The probe insertions are controlled by the same technology that controls our code coverage instrumentation, which ensures that the probes function correctly regardless of the compiler, target processor, or run-time environment.
-
Product
PCB Test And Design-For-Test Services Group
-
ntellitech has a very experienced consulting and test development organization that is dedicated to provide our customers with high-quality design and test services. Choosing Intellitech Test Services can help you lower the risk of adopting a new Design-for-Test methodology or speed your product to market when you need to deploy a test solution quickly.
-
Product
Temperature Chambers For Thermal Tests
-
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
Product
CAM/GATE Test Kits
Series 45
-
The CG Series 45 CAM/GATE linear over clamp kits utilize the same patented “Z” axis motion as our CAM/TRAC® Series products offering precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The latch assembly engages and disengages when actuating the clamping assembly. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components
