Particle Impact Noise Detection
vibration, shock, and acoustics testing conducted to find particulate contamination.
See Also: Particle Impact Noise Detectors, PIND
-
product
Ultra Low Noise, Rubidium Frequency Standard.
A10-M
Frequency Referencing, Calibration, Standards Lab, Production Test for Oscillator Manufacturers. A very high stability LOW NOISE 10MHz Rubidium Reference, primarily for production test of quartz oscillators and RF instrumentation frequency referencing. This industry standard 2U rack-mount instrument has a long heritage and ongoing production life for this latest 2009 version that features RS232 monitoring and control of the DPLL, locking the Ultra Low Noise OCXO to the Rubidium. Damping and Bandwidth is controlled by integrator digital gain, proportional digital gain, pre-filter order and subsample rate. Eight values of user selected bandwidth are available.
-
product
Noise Source, 10 MHz to 26.5 GHz, nominal ENR 15 dB
346C
The Keysight 346C noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 26.5 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. Option K01 is a coaxial noise source and features coverage from 1 to 50 GHz with a 2.4 mm coaxial connector.
-
product
Minimal Signal Noise
SCSI Quiet Cables
Paralan Corporation was one of the first companies to recognize that 90% of the problems with SCSI Bus installations lie with the cables. To address this problem, Paralan developed its own line of high-quality shielded Quiet Cables.
-
product
Low Noise Amplifier
ZLNA-9K-6G-01
Low Noise Amplifier, Frequency 0.009~6000MHz, Gain 40dB, Noise figure 3.5dB, P-1dB power 8dBm, SMA Female
-
product
Partial Discharge Detection and Localization System for Power Transformers
AE-150™
The AE-150™ is designed to detect and localize Partial Discharge activity by correlating acoustic and electric sensors’ data. The AE-150™ has many acquisition modes, each used for detecting and locating Partial Discharge activity in a transformer. The AE-150™ unit is mounted on the transformer tank using its powerful magnets that also hold four acoustic sensors. Acquired data is sent to Mirador-Tx software where all advanced positioning functions are implemented. This cutting-edge software allows easy data interpretation, reporting and monitoring.
-
product
Manhole Impact Tester
Manhole Impact Tester is used to test the impact performance of manhole base and manhole wall.
-
product
Radiation Detection
Radiation detectors for safety quality assurance is top of mind for hospitals, nuclear power facilities, nuclear medicine laboratories, x-ray manufacturers, government agencies, state inspectors, emergency response and HAZMAT teams, and police and fire departments around the world. Fluke Biomedical offers a complete line of radiation detection, personal dosimeters, staff radiation dosimeter monitoring, and safety products and solutions that allow these professionals the versatility they need to get the job done and the quality they trust in a radiation-safety device.
-
product
High Sensitivity Helium Leak Detection System
HSHLD® MODEL 310
ORS manufactures the HSHLD® Model 310 High Sensitivity Helium Leak Detection System, a Quadrupole Mass Spectrometer system for High Sensitivity Helium Leak Rate measurement to qualify your product to the latest, tighter leak rate requirements of Mil-Std-883, Method 1014. Our model HSHLD® Model 310 uses conventional mass spectrometer helium leak test technology. This gives you enhanced spectrometer sensitivity at a modest cost. The system is modular, automated, flexible, fast, easy to calibrate, easy to use, and is affordable. Both the FINE and GROSS leak test is performed in a single test sequence.
-
product
Community Noise Prediction Software, Version 2
SPM9613
A low-cost computer program for analyzing community noise and sound propagation emitted from a variety of noise sources. The engineering software is based on the ISO 9613 parts 1 and 2 standards. SPM9613 provides calculations at specific field points (listeners) and predictions of A- and C-weighted sound level contours as well.
-
product
Real-Time Analysis up to 255 MHz, Basic Detection, Multi-touch
N9041B-RT1
See, capture, and understand elusive signals as short as 17.17 s with 100% POI and a complete set of advanced triggers, up to 110 GHz View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 VSA software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Fault Detection Device in PV String
Hanwa Electronic Ind. Co.,Ltd.
◆Very light and easy to carry.◆Possible to find fault areas that can’t find by Voc.◆Measurement Voc and Vc.◆Possible to check data and record the data using Android.
-
product
Low Noise Triple Band Voltage Controlled Oscillator
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
product
Carrier to Noise Generators
CNG-DX
Hollis Electronics Company LLC
CNG-DX provides improved noise generation with its internal digital power meter and built-in noise generator. This single instrument provides accurate and repetitive carrier-to-noise setting ability in one box. The CNG-DX is an ideal instrument for creating realistic scenarios for closed loop testing of satellites, ground equipment and mobile transceivers.
-
product
Phase Noise Measurement Solutions
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
product
Pendulum Impact Testers
MPX
Delivering precision and safety in high-volume materials testing, the MPX pendulum impact system from Instron is optimized for Charpy and Izod testing of metals. Equipped with Bluehill Impact software, it supports capacities from 300 J to 900 J and features motorized hammer lift, automatic return, and interchangeable hammer weights. An enclosed, interlocked safety guard ensures operator protection in compliance with CE and ISO 13849 standards. The system supports key standards including ASTM E23, ISO 148, EN 10045, and others, while offering configurable reports and seamless data export capabilities.
-
product
Fingerprint Detection, Capture & Enhancement
Recognised for innovation in the field of latent fingerprints, our product range includes advanced systems for the development of fingerprints using traditional time honoured methods alongside new and novel techniques developed exclusively by Foster + Freeman.
-
product
Detective Logic Analyzer
DDR3
Provides logic analyzer like deep transaction Listing and Waveform captureCan store up to 1G of captured StatesContinuous, real time analysis, not post-processingEye Detector guarantees valid data acquisitionExtensive Triggering and Storage Qualification allows precise insightProtocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specificationsRow Hammer Analysis for potential data corruptionInteractions among up to 8 ranks, over two slots are analyzed.Mode Register Listing providedSupports Auto-Clock rate detect and clock stoppage Connects to the target under test with DIMM, SO-DIMM, and BGA interposers or a midbus probeIntegrated Microsoft Charts gives quick insight into large trace capturesTrigger In & Out allows the Detective to integrate with other test tools
-
product
Air Particle Counters
These air particle counters can measure particle in air, with airflow 2.83L/min and 28.3L/min large air flow .
-
product
Low Noise Prepolarized Microphone
378A04
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
product
Mobile Trace Detection
TR-TRACE
Lightweight, easy to use, real-time trace detection equipment solutions for mobile security screening operations.
-
product
Fall Detection Switches
Panasonic Industrial Devices Sales Company of America
Compact tip sensor with reliable photo sensor design. Applications include: Gas Heaters, Electric Fans.
-
product
Reticle / Mask Particle Detection System
PR-PD2HR
In semiconductor plants, where high performance and demanding functionality are required, the HORIBA PD Series'' high operating rate and long-term dependability have earned it a solid reputation. Inheriting a transfer system that has proven to provide stable, high performance and superior throughput over long operating periods, the PR-PD2HR now offers the most sensitive detection in the series with exclusive signal processing that can detect particles as small as 0.35 m.
-
product
Slip Line Detection System
YIS 200
The YIS and SF Series metrology systems are designed for optical detection of wafer defects such as crystaldislocations, slip and other defects. The YIS-300HM (for 300 mm wafers) and YIS-200HM (for 200 mm wafers) utilizeMakyoh optics technology (Magic Mirror) and integrated robotic wafer handler provided by Hologenix.
-
product
Impact Tester - Impact Testing Machine
Impact tests are used to measure the resistance to failure of materials to a suddenly applied force. The test measures the impact energy, or the energy absorbed prior to fracture. ToronTech™ offers advanced Impact testing machines to measure that energy through drop weigh tear test and Charpy impact test. We also offer machines for the preparation of specimens for these tests.
-
product
Automatic Incident Detection
TrafiBot2
The FLIR TrafiBot2 is a compact, rugged camera solution for automatic incident detection. Combining full HD visual imaging with advanced video analytics, TrafiBot2's advanced processing generates traffic data and incident detection information for tunnels, bridges, and highways, including alerts on stopped vehicles, wrong-way drivers, and lost cargo.
-
product
Impact Testing Machine (Izod & Charpy)
Suitable for Charpy & Izod Impact tests on different materials. It is based on Pendulum principle.Rigid designs of instrument frame & other parts assure minimum energy absorption during fracture which results in improved test accuracies.The highly strained & wearing parts like support blocks & strikers are of special alloy steels duly heat treated.Direct indication of Impact energy absorbed by sample on large dial -Safety guard for the user is provided.Initial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a Least Count of 2 Joules (for Analogue models) & resolution of 0.5 Joules (for Digital Model).Drop Angle of Pendulum for Charpy is 140° & for Izod is 90°.ASTM Impact Testing machine is also provided, which conforms to E-23 ASTM standard.Gauges, Tongs, Sub-zero bath, Templates, U & V Notch milling cutters are available with it (Optional).
-
product
Noise Figure Measurements With Vector Correction
S96029B
This software application enables high-accuracy noise figure and noise-power measurements of amplifiers. It utilizes Keysight’s unique vector-source-correction technique, which uses a source-impedance tuner to remove the effects of imperfect system-source match. This approach yields accuracy that surpasses that provided by the Y-factor method and other cold-source implementations, especially for in-fixture, on-wafer, and automated-test environments. A scalar-calibrated method is also available that offers less accuracy but is faster and does not require an impedance tuner.
-
product
Button Impact Tester
TESTEX Testing Equipment Systems Ltd.
Button Impact Tester, to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Cracking, chipping or breakage constitutes failure.
-
product
10 MHz to 55 GHz Noise Sources
CNS346 Series
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
product
Portable Metal Detection System
XT 8000
The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport. Only $3,995.00 eachBuy NowOur Price $3,995.00 The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport.XT 8000 is simple to set up and operate without specialized training. The system can be moved regularly to different facilities to provide security and deterrence while costing thousands less than permanently installing units at each site.
