Particle Impact Noise Detection
vibration, shock, and acoustics testing conducted to find particulate contamination.
See Also: Particle Impact Noise Detectors, PIND
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
Magnetic Particle Inspection Systems for Non-Destructive Testing (NDT)
-
VERIFY SURFACE AND SUBSURFACE STRUCTURAL INTEGRITY IN: Industrial Crankshafts, Ferrous Parts, Aircraft Components, Landing Gear Components.
-
-
Product
Airborne Particle Counters
-
Complete contamination control solution including cleanroom certification and clean area monitoring, while meeting global requirements for data integrity.
-
Product
Gas Detection Controller
MX 43
-
Teledyne Gas & Flame Detection
Fully scalable, and designed to functional safety performance level 1 standards, the MX 43 is an analog and digital controller that continuously measures and controls gases in the atmosphere. The MX 43 gas detector manages both digital lines and analog channels, and covers all needs for a wide variety of gas monitoring applications. The MX 43 digital technology allows up to 32 detectors to be distributed on 8 lines for increased cost savings.
-
Product
Real-Time Pulse Detection Firmware
FWPD
-
The core challenge in pulse detection is to design a system for random events. The Teledyne SP Devices’s firmware option FWPD, for the ADQ14 and ADQ7, is tailored to detected and analyze pulses in demanding measurement applications where the properties of the pulses (such as timing or length) are not known in advance.
-
Product
14 Slot, 3U, 350W, PXI Chassis - Low Noise Fan
40-914-201
Chassis
This PXI chassis includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 13 more 3U peripheral modules.
-
Product
Magnetic Particle Flaw Detector
MT-1A
-
MT-1A digital portable magnetic flaw detector, adopts large capacity lithium battery power supply. DC is exchanged into AC by the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 4 hours. The battery can be charged while working or off. It can real-time monitoring, process image, save data, print the test report, track inspection results, meet the requirements of standard operation and management. Especially suitable for the field without power supply field testing and high-altitude operations, it realizes the innovation of magnetic powder digital inspection.
-
-
Product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
-
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
-
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
Product
Phase Noise Tester 5MHz to 40GHz
Model 7340
-
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
Bleed Air Leak Detection System For Aerospace
-
Ideal for composite aircraft. Our revolutionary detector network accurately locates potentially catastrophic leaks in bleed air systems. By activating a cockpit alarm, it enables mechanics to find the affected areas fast and with precision.
-
Product
Automatic Audio-Video Sync Detection
BATON® LipSync
-
BATON® LipSync is an automated tool for lip sync detection and verification. BATON LipSync leverages image processing and machine learning (ML) technology and deep neural networks to automatically detect audio and video sync errors. Using BATON LipSync, broadcasters and service providers can accurately detect audio lead and lag issues in media content in order to provide a superior quality of experience (QoE) to viewers.
-
Product
Film Impact Tester
QT-FIT-3J
-
The impact resistance of films is obtained by measuring the energy consumed by hemispheric impact head to make films rupture under controlled impact conditions to evaluate the impact resistance of material and its effects.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
Particle Size Analyzers
NanoBrook Series
-
Brookhaven Instruments Corporation
Rapid and accurate protein & nanoparticle size distributionsMultimodal & unimodal size distribution softwareISO 13321 and ISO 22412 compliant resultsRange: < 0.3 nm to 10 mThree measurement angles: 15, 90, and 173Ideal for fast, routine sizing applications in research or quality controlHigh power 35 mW diode laserDynamic light scattering at 173 and 90Temperature control, -5 C to 110 CCompact bench top unit, USB connectionMolecular weight determination (relative and absolute through Debye plot)
-
Product
Pipe-mountable Liquid Level Detection Sensor
EX-F1
-
Panasonic Industrial Devices Sales Company of America
The EX-F1 Pipe-Mountable Liquid Level Detection Sensor can not only be easily mounted onto a pipe with just tying bands, but it requires minimal mounting space thanks to its' built-in amplifier and compact size. Positioning can also be easily changed with the release lever even after mounting.
-
Product
NTA Particle Size Analyzers
NanoSight Range
-
The Malvern Panalytical NanoSight range of instruments utilizes Nanoparticle Tracking Analysis (NTA) to characterize nanoparticles from 10nm -2000nm* in solution. Each particle is individually but simultaneously analyzed by direct observation and measurement of diffusion events. This particle-by-particle methodology produces high resolution results for nanoparticle size distribution and concentration, while visual validation provides users with additional confidence in their data. Both particle size and concentration are measured, while a fluorescence mode provides differentiation of intrinsic or fluorescently labelled nanoparticles.
-
Product
The Ultra Low Noise Streamer
Sentinel® RD
-
Providing an unsurpassed signal-to-noise performance, Sentinel RD is the best-in-class solid streamer available on the market. In both calm and adverse weather conditions and irrespective of towing depth, Sentinel RD produces the highest-quality seismic data, resulting in the clearest seismic image.
-
Product
IK07-IK10 Pendulum Impact Hammer Apparatus
-
Shenzhen Chuangxin Instruments Co., Ltd.
IK07-IK10 Pendulum Impact Hammer Apparatus is desinged according to IEC60068-2-75 and IEC62262 standards. The IK07-IK10 Pendulum Impact Hammer Apparatus can be used for the mechanical impact strength test of metal enclosure.
-
Product
High Frequency Noise Simulator
SKS-H04GA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
-
Product
IEC60068-2-75 Ik08 Spring Impact Hammer
CX-IK08
-
Shenzhen Chuangxin Instruments Co., Ltd.
The spring Hammer consists of three principal parts: the body, the striking element and the release system. It's used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance with IEC/EN, UL/CSA and other international standards.
-
Product
Infrared Camera for CO Detection and Electrical Inspections
FLIR GF346
-
The FLIR GF346 optical gas imaging camera detects carbon monoxide (CO) and 17 additional gases without the need to interrupt your plant's production process. CO emissions can be a significant threat to primary steel manufacturing operations; even the slightest leak in a vent stack or pipe can have a devastating effect. With the FLIR GF346, inspectors can scan large areas from a safe distance, pinpointing leaks in real-time, reducing repair down-time, and providing repair verification.
-
Product
Particle Size Analyzers
Mastersizer Range
-
The Mastersizer range of laser diffraction particle size analyzers set the standard for delivering rapid, accurate particle size distributions for both wet and dry dispersions. From assessing product uniformity and solubility, through to optimising packing density to improve final product performance and controlling powder flowability to increase manufacturing efficiency, particle size analysis is critical to understanding and controlling a wide range of properties. The Mastersizer range, with its intuitive software and industry-leading design and ergonomics, enables users to make these particle sizing measurements fast and routine.
-
Product
Particle Counters
-
A particle counter is a useful tool for monitoring indoor air quality (IAQ) in clean rooms and workplaces, as a particle counter measures the concentration of particles in the air. While a particle counter won't identify specifically what kinds of dusts or particulates are present in the air, a particle counter will identify how many airborne particles of a certain size are present in the environment. A conclusion is then drawn based on the known materials in the area and the corresponding airborne particle sizes of those materials. Here at PCE, We can offer you a wide range of dust particle analyzers to suit your needs.
-
Product
IEC 60068-2-75 IK Spring Impact Hammer
CX-T01
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC 60068-2-75 IK Spring Impact Hammer is used for IK Testing. And The IEC 60068-2-75 IK Spring Impact Hammer can be customized the force of 0.14J, 0.2J, 0.35J, 0.5J, 0.7J, 1.0J and 2.0J.
