Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8065
-
The Technobox, Inc. P/N 8065 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
-
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
Product
NI FlexRIO Adapter Modules
-
High bandwidth and high resolution AWGs help you to generate with confidence complex signals like digital modulations and RF stimuli for functional and performance tests.
-
-
Product
Adaptive Clocking (TCK) Adapter
-
Blackhawk has extensive experience in emulation design and can help you with any emulation requirement. We can taylor a solution based on cost, form factor, host interface and performance to meet your needs.
-
Product
Osprey ISA Q-Bus Adapter board
9476-Q-B
-
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
Product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
-
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
Single Front Slot + Single Rear Slot Universal PCI to PCMCIA Adapter
P416
-
The P416 addresses the need to have front access to a PCMCIA slot for use with cards like Flash media, or Finger Print recognition, while also having a rear slot for cards that are less frequently swapped, like Wireless LAN or Bluetooth. The rear slot is 32-bit capable meaning it supports CardBus cards which makes it forward compatible with some of the newer high speed Wireless LAN standards like 802.11a and 11g.
-
Product
GPIB to Ethernet to Instrument Interface
Model 4865B
-
* Adds a GPIB Interface to Instruments with a VXI-11 or Raw Socket Ethernet Interface.* Transparent data transfer handles ASCII and binary data.* Controllable with any IEEE-488.2 GPIB Controller* VXI-11 protocol supports control, abort and reverse channels.* Raw Socket protocol includes substitute command strings for GPIB Device Trigger, Device Clear and Interface Clear.* Auto-Find feature simplifies instrument linkage* Reuses existing test software with new Ethernet instruments.* Easy configuration with the 4865B's internal webserver.* Drop in replacement for the original Model 4865 with 2x to 5x speed increase.* 1 U high rack mount kit mounts one or two 4865Bs.* Includes universal 115/230 VAC Power Adapter.
-
Product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
-
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
-
Product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-02
Digital I/O Adapter
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
Product
Osprey ISA Unibus Adapter
9476-U-B
-
Unibus Controller board is EISA/ISA bus compatible and occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
-
Product
3U Grille Adapter
AD-5
-
Used to install 19” panel width blowers, fan and grille/filter assemblies in 24” panel width enclosures.
-
Product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
RF Adapter Module
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 2x96 Male SCSI Connector
510109591
PCB Adapter
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI Connector
-
Product
Relay Buddy Adapter Set
190-4
-
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
Product
Pull-Thru Adapter, Wired, for Pickering 40-161-101
510140177
Pull-Thru Adapter
Pull-Thru Adapter, Wired, for Pickering 40-161-101
-
Product
Cable Assembly, Receiver, QuadraPaddle & Mini Coax, 36", PCB Adapter
540103010258
Cable Assembly
This cable assembly comes with PCB adapter 510150210 and a Mini Coax module to 4 SMB plugs.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Female VHDCI Connectors
510150126
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Female VHDCI Connectors
-
Product
SSOP-to-DIP Adaptor
Series 351000
-
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
-
Product
Flexible MiniPCI Express to 2 MiniPCI Splitter
SKU-069-2X
-
Flexible MiniPCI Express to 2 MiniPCI Splitter (Splitter) was designed to expand a modern motherboard (ATX, mini ATX etc.) that doesn’t have the MiniPCI interface. It allows you to connect up to two (2) 124-pin MiniPCI add-in boards to a motherboard’s standard MiniPCI Express connector.Splitter includes 2 MiniPCI Adapter boards, MiniPCI Express Host board and 2 Flat PCI Express Cables.
-
Product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
PCB Adapter
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
-
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
