Spectrum Analyzers
analyze the spectra of signal versus frequency.
See Also: Audio Spectrum Analyzers, Optical Spectrum Analyzers, RF Spectrum Analyzers
-
Product
Preamplifiers
LNA Series
-
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
4.4 GHz Spectrum Analyzer
USB-SA44B
-
The Signal Hound USB-SA44B is a Software Defined Receiver (SDR) optimized as a narrow-band real-time spectrum analyzer. It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists.
-
Product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Signal Analyzer
-
bsw TestSystems & Consulting AG
The simplest way to measure the phase noise is to compare the Device-Under-Test (DUT) to the source of a spectrum analyzer. With the SA set at the same frequency as the OUT, you see the sum of the SA's and DUT's sideband-power spectrum on the SA display. It is a simple and straight forward method well suited for free running VCO's where the SA is easily an order better.You can improve on this method by establishing a Phase Lock (PLL) between the DUT and the Local Oscillator and create a zero-IF or base-band spectrum analyzer system.
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-03
-
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Signal And Spectrum Analyzer
FSVA3000
-
An analysis bandwidth of 400 MHz, an outstanding phase noise of –120 dBc/Hz and a high dynamic range – the R&S®FSVA3000 signal and spectrum analyzer has everything needed to keep up with demanding measurement applications such as 5G NR. With its high measurement speed and easy usability, it is the right instrument for demanding signal analysis tasks both in the lab and on a production line.
-
Product
Spectrum Analyzers
SSA3000X Series
-
Siglent’s SSA3000X family of spectrum analyzers offer a frequency range of 9 KHz to 2.1/3.2 GHz. With their light weight, small size, and friendly user interface, the SSA3000s present a large, bright easy to read display, powerful and reliable automatic measurements, and plenty of impressive features. Applications include research and development, education, production, maintenance, and pre-compliance testing.
-
Product
Waveguide Harmonic Mixer, 75 to 110 GHz
11970W
-
The 11970W extends the frequency range of the Keysight N9030A PXA high-performance signal analyzer to the W-band (75 to 110 GHz). It is also fully compatible with other Keysight spectrum analyzers including: the E4440A/46A/48A PSA (with Option AYZ), the E4407B ESA-E (with Option AYZ), the 856xEC, the 8566B (with a preamplifier), and the 7000 modular analyzer (with the 70907A/B external mixer interface module).
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Product
Spectrum Analyzer
BB60C
-
The BB60C streams 140 MB/sec of digitized RF to your PC utilizing USB 3.0, providing an instantaneous bandwidth of 27 MHz, and sweep speeds of 24 GHz/sec. The BB60C has significantly improved performance compared to the BB60A. The BB60C has improved spurious-free dynamic range (SFDR) by 20 dB, flattened the noise floor and band transitions by more than 8 dB, and extended operating temperatures from -40ºC to +65ºC (Option 1). The BB60C also adds new functionality in the form of configurable I/Q streaming bandwidths which will be retroactively available on the BB60A.
-
Product
Optical Spectrum Analyzer
-
an optical spectrum analyzer for analyzing short wavelengths from 350nm to 1000 nm. Because it adopts a Fourier spectrum system with a Michelson interferometer, the 8341 can measure the coherence. With its narrow wavelength resolution of 0.01nm * , the 8341 is very effective for the evaluation of not only CD/DVD laser diodes, but also for blue-violet laser diodes. In addition, the built-in He-Ne laser acts as a wavelength reference to ensure a high wavelength measurement accuracy of ±0.01nm * . Finally, with its fast 0.5s * measurement speed, the 8341 is ideal for building into systems for mass production and evaluating temperature characteristics of system components.
-
Product
Handheld Digital Spectrum Analyzer
RF Explorer - 3G Combo
-
This model includes a WSUB1G baseline unit plus an RFEMWSUB3G Expansion Module conveniently assembled and tested. It comes with two SMA connectors and two antennas,a nice Nagoya NA-773 wideband telescopic antenna for all Sub-GHz frequencies and a whip helical for 2.4GHz band. Additional, specific band antennas may be needed to cover efficiently some of the frequencies supported.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
Digital Hybrid Wireless® Compact Receiver
UCR411a
-
The UCR411A receiver provides professional performance and a versatile feature set in a compact design for field and location production. All settings are made from the front panel with a powerful LCD interface, making the unit ideal for use on sound carts, in portable bags, and in rack-mount multi-couplers. To alleviate interference problems in an increasingly congested RF spectrum, an RF spectrum analyzer is built into the receiver. The receiver tunes across its 25.6 MHz tuning range and records RF activity with markers on the LCD screen. Finding clear operating frequencies is a quick, simple process. The UCR411A is compatible with all 400 Series Lectrosonics wireless transmitters (and some other transmitter types) and can be powered with internal 9V batteries or external DC.
-
Product
FieldFox Handheld Microwave Analyzer, 18 GHz
N9917A
-
18 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
Digital Broadcast Analyzer
-
Spectrum Analyzer: 9 kHz 4 GHzInterference Analyzer with Interference MappingHigh Accuracy Power Meter, 2-port Transmission MeasurementsCoverage Mapping, Channel Scanner, GPS, AM/FM/PM Analyzer3GPP, 3GPP2, WiMAX, signal analyzersTracking Generator: 500 kHz 4 GHzDigital TV ISDB-T, DVB-T/H analyzersCPRI RF MeasurementsField-proven design: Three-hour battery life, rugged, compact, lightweight, daylight viewable displayIntuitive menu-driven touchscreen user interfacePIM Alert (a downloadable easyTest script)Standard three-year warranty (battery one-year warranty)
-
Product
Spectrum Analyzer Extenders
-
RPG's Spectrum Ananlyzer Extenders allow high performance broad-band down-conversion and frequency extension of microwave spectrum analyzers into the THz range.
-
Product
Tunable Non-Reflective Band-Reject Filter (700MHz-1GHz)
SPCL-00597
-
This device is placed after the DUT to protect the Spectrum Analyzer from high-power fundamentals and provide harmonic measurements. The non-reflective functionality prevents energy from bouncing back to the DUT and raising the noise floor level.Broadband matching improves dynamic range and reducesmeasurement uncertainty.
-
Product
FieldFox Handheld Microwave Analyzer, 14 GHz
N9916B
-
A lightweight, durable, cable and antenna analyzer, spectrum analyzer, network analyzer, and more
-
Product
WiFiScope WS5: 500 MS/s 250MHz BW, 2 Channel, Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
WS5-540XM-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
Product
High Performance 9 kHz - 1200 MHz SDR
CloudSDR
-
The CloudSDR''s remote mode also offers a variable width spectrum analyzer with adjustable spans up to 10 MHz wide. The spectrum information update rate can be adjusted up to 10 Hz or turned off to limit the bandwidth utilization. In addition, the built-in squelch can be used to limit data transmission when no signals are present. Wideband spectrum analyzer mode offers 56 MHz wide spectral captures in both 2D, 3D and waterfall formats.
-
Product
RF Training Kit And Lab Sheets
Y1800A
-
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
Product
FieldFox Handheld Microwave Analyzer, 50 GHz
N9952A
-
50 GHz max frequency Carry industry's first 50 GHz handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 6.5 GHz
N9934B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
ESU Analyzer
vPad-ESU
-
Built on our Vision-Pad platform, vPad-ESU has all the functionality you have come to expect from products built on this platform. What really makes this product unique is its built-in HF Digital Scope and Spectrum Analyzer.
-
Product
FieldFox C Handheld Microwave Spectrum Analyzer, 10 GHz
N9935C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth.Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup.Perform over-the-air measurements for 5G NR and LTE.Use GPS/GNSS for geolocation and timestamping.Carry one lightweight unit at 3.4 kg (7.4 lb).What's included:Base model: spectrum analyzer (SA)AC/DC adapterLocalized power cordRechargeable Li-ion batterySoft carrying case with backpack and shoulder straps
-
Product
Test Automation Software
-
PathWave test and measurement software delivers fast, accurate, and comprehensive data analysis. Connected workflows and trusted algorithms allow you to optimize test plans while increasing test efficiency. Designed for spectrum analyzers, oscilloscopes, network analyzers and many more test instruments as well as PCs or automation systems.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 9 GHz
N9935B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
