Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
CAN + OBD Network Data Converter
NC1
-
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
Product
Vsync™ Controls Platform
-
Vsync™ is RedViking’s 4th generation powertrain dynamic testing software, based on over 100 fielded dynamic component test benches. Developed by RedViking for aerospace, automotive and off-highway test labs. Your lab or end-of-line test stand won’t have to rely on multiple stand-alone systems with limited data acquisition and analysis capabilities. Vsync™ provides an integrated, user-friendly platform for indisputable test data with superior repeatability and traceability.
-
Product
PXI 4 Banks of 20 Channel 1 Pole MUX
40-615-021-4/20/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
ARINC-717 Bus
-
The ARINC 717 bus defines the communication between DFDAU(Digital Flight Data Acquisition Unit) and the DFDR(Digital Flight Data Recorder). The Data over the bus is a collection of all various data to be recorded.
-
Product
Counter DAQ Cards
-
Counter card series include pulse output, event counting, PWM measurement/output and encoder reading functions.
-
Product
CB-37FH, DIN-Rail Horizontal Mount 37-Pin Spring TB
778676-01
Terminal Block
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it featuresscrew or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Product
ActiveX Controls for ADLINK DAQ/DAQe/PXI-2000 Series Cards (Vista Ready)
D2K-OCX
-
D2K-OCX ActiveX controls communicate with ADLINK data acquisition cards to perform digital, analog, and timer/counter operations. These ActiveX controls well-designed to hide all details of hardware manipulation so the data acquisition operations can be achieved by only few lines of codes. Furthermore, any hardware configuration can be done with the easy-to-use property pages, and the acquired data is returned in a event-driven manner.
-
Product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782260-01
Multifunction I/O
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Intel 186 EB & EC Processor Boards
MS 1503
-
- ATE- Data Acquisition System- Process Control- Industrial Automation
-
Product
6U cPCI / PXI / PXIe 6021 Full Size Chassis
-
The WIENER 6021 crate series can be outfitted with cPCI, PXI or PXIe backplanes to provide high performance chassis with highly reliable low-noise power supplies for these bus standards. Typical applications are data acquisition, beam line control and test instrumentation.
-
Product
Potentiostat/Galvinostat Electrochemical Instuments
-
- 16 bit DAQ card- 250 kS/s aggregate- 125 kS/s per channel- Step Impedance Spectroscopy- Electrochemical impedance spectroscopy (EIS) 0.01 – 10 kHz- 5-lead cable (3 electrodes, sense & ground)- LabVIEW EZware software- Free software upgrades. 1 year parts and labor warranty- EIS information
-
Product
Processor
DAP 4000a
-
Use the DAP 4000a in data acquisition and control applications that require light-to-moderate real-time processing.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI-Express, 16 SE/8 DIFF Analog Inputs, 8 Analog Outputs,16-bit, 8 Digital I/O, 24 V
APCIE-3021-16-3
-
The PCI-Express analog input/output board APCIe-3121 has 16 SE/differential inputs, 8 analog outputs, 16-bit, and 8 digital I/O, 24 V. The board is especially suited for applications in industrial process control, measurement technology and monitoring, for example for multichannel data acquisition, for the control of chemical processes, for the acquisition of sensor data, current measurement etc. in the harsh industrial environment.
-
Product
External Measuring Systems
LAN, USB
-
An alternative for measuring cards integrated in a PC are external data acquisition systems from BMCM. In this case, sampled data are transmitted to the PC via the USB interface or the LAN network - perfect for mobile applications!
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
Product
NI-9862, CAN Interface Module
781639-01
Interface Module
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
GPC/SEC Data Systems for Enhanced Control and Performance
-
Agilent GPC/SEC data systems enable powerful control, data acquisition, calculations, and result reporting. For accurate molecular weight analysis and complete polymer and protein characterization, GPC/SEC software provides the functionality required for conventional and advanced GPC/SEC in a simple, powerful, fully integrated package.GPC/SEC software for OpenLAB CDS adds application-specific calibration, data processing, and reporting to your OpenLAB CDS. Cirrus GPC Multi Detector software, an add-on to OpenLAB CDS ChemStation, allows you to process conventional GPC data using a column calibration. Bio-SEC software is a dedicated standalone package for characterisation of proteins and other biomolecules.
-
Product
DynoLAB Test Cell Supervisory System
-
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
Product
PXI 2 Amp MUX, Single 8-Channel 4-Pole
40-635-103
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
787805-33
Controller
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
PXI 2 Amp MUX, Single 32-Channel 2-Pole
40-635-002
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
MPOD Mix Crate
-
Mpod EC and LX models can be customized to integrate a Wiener or a custom 3U to 6U bus backplane (VME, VME64x, cPCI, …). All voltages required from the backplane specifications are provided. When no rear transition modules are needed, these compact solutions allow saving money and space by reducing the number of needed crates, i.e. combining power supply with DAQ.
-
Product
cRIO-9055, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller
787043-01
Embedded Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9055 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PXI Base Module
PA72
-
The PA72 platform is a platform of flexibility. It consists of a base board and one or two daughter boards. In daughter boards there is choice from several different generators, digitizers, filters, and Flexible Digital I/O modules. Also custom daughter boards can easily be created. This allows you to configure a data acquisition card exactly tailored to your needs. The PA72 concept provides a flexible and cost effective solution for medium and high end analog functions.
-
-
Product
SH68F-68F-EPM Cable , 68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable
199006-05
Multifunction Cable
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
Product
Software
DASYLAB Lite
-
Dasylab lite software for operation of our line of THERMES Data Acquisition Systems. For customers who already have Labview or Dasylab no additional software is necessary. Recommended operating software is Dasylab Lite version 10. The lite version provides all the necessary functions to display and store temperature data in digital and graphical formats in real time. Users may customize the display to suit their particular application. The Dasylab Basic version provides additional features for data manipulation and statistical analysis.
-
Product
Data Acquisition System/Digital Multimeter
2638A Hydra Series III
-
The Fluke Hydra Series III continues the Hydra Series legacy of precision, multi-channel data acquisition. The new Series III improves on Hydra's industry-leading thermocouple accuracy and adds a new dimension to how you collect and view data in a portable system.
