Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
2WD Dynamometers
MD-250 Series
-
The MD-250 uses its powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system.
-
Product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
Analog Input Module
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
Product
16 Channel ADC for CompactPCI
CPCI392
-
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
Single 24x8 1-Pole High-Density PXI Matrix Module
40-520-202
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Data Acquisition Equipment
-
Get the data you want, where, how and when you want it. Fluke gives you a broad choice in data acquisition for process monitoring and laboratory test systems. You can choose a stationary or portable data logger. Transfer data to internal memory, to a removable memory card, or to your PC. Choose a standalone or distributed networked units. And you can expand your system from 20 to 1,000+ channels, depending on the series.
-
Product
Powered VME64x Crates
6U VME64x 554-x Mini
-
The VME554-x mini crate is the perfect choice for data acquisition, test and debugging applications.
-
Product
New Generation Marine Seismic Recorder
Seal 428
-
The Seal 428 is the new large capacity and high-resolution seismic data acquisition system designed for marine towed streamers acquisition. It derives its high reliability and versatility from SERCEL’s extensive experience in cable telemetry systems and from the use of the most advanced electronics and workstation technology.
-
Product
PXI High Density Screened Mux 5 Ch 16 Pole
40-670A-021-S-5/16
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.803-08
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Load Banks
-
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
Product
eXpert FPGA DSP Features for Data Acquisition
-
GaGe provides several eXpert FPGA processing firmware options for use with CompuScope Digitizers. All standard default CompuScope Digitizer model configurations can store raw acquired waveform data to onboard sample memory and then transfer them quickly to the user for analysis, display and/or storage. The addition of optional eXpert FPGA processing firmware features allow for some signal processing analysis, or other specific functionality, to be performed on the digitizer hardware itself within its onboard Field Programmable Gate Array (FPGA).
-
Product
Serial Data Acquisition And Control Interfaces
-
ICS's Serial to Data Acquisition and Control Interfaces are IEEE-488.2 compliant and and provide GPIB functionality over a serial link. Click on a link or scroll down to access the appropriate Serial Digital Interface:Our Serial to Data Acquisition and Control Interfaces have non-isolated analog and digital signals. Click here for our isolated Serial to Analog Interfaces.
-
Product
Modular Recording System
-
Modular and flexible solutions that don't sacrifice speed are the future of high-speed data acquisition technology. That's why Conduant developed a modular recording platform—so you can have the best of both worlds.
-
Product
PXI/PXIe Very High Density Multiplexer, 24-Channel, 8-Pole
42-675B-002-24/8
Multiplexer Module
The 40-675B-002-24/8 (PXI) and the 42-675B-002-24/8 (PXIe) are 24-channel, 8-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
SH68F-68F-EPM, 68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable
199006-01
Multifunction Cable
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
Product
CB-37F-HVD, 37-pin ScrewTerminal Blk, UL rec.150V CAT II, Din Rail
779491-01
-
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, High Voltage Horizontal DIN Rail Terminal Block - The CB-37F-HVD features screw terminal connectivity for up to 37 I/O signals, 12 to 30 AWG. It has a female 37-pin D-SUB connector for connectivity to C Series I/O Modules and … data acquisition devices. The CB-37F-VHD is UL recognized. You can use the CB-37F-VHD with low-voltage or high-voltage products up to 150 V.
-
Product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Network Interface Controller
SPIDAR®
-
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
Product
PXIe-6396, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785927-01
Multifunction I/O
PXIe, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6396 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6396 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Distributed Motion Control
-
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
Product
WiFiScope WS6+SureConnect: 200 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-200XMS-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
Product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - PCIe
Model 78132
-
Model 78132 is a member of the JadeTM family of high-performance PCIe boards. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power andcost, while still providing some of the highest-performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deployingFPGA-based data acquisition and processing. The 78132 is a multichannel, high-speed data converter with programmable DDCs (digital downconverters). It is suitable for connection to HF or IF ports of a communications or radar system. Its built-in datacapture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
-
Product
Dragonfly
-
HGL Dynamics presents its Dragonfly range of miniature high-performance data acquisition cards and support modules.The world of digital data acquisition has matured over the past few years, with a range of vendors (including HGL Dynamics) offering high-quality and performance data acquisition products in a variety of form factors, with one exception: miniature, vehicle-mounted, high-performance and ultra low-power modules. Dragonfly from HGL fills this area.
-
Product
PXI Dual 12x8 Matrix, 2 Pole Switching
40-522-022
Matrix Switch Module
Medium density PXI dual 12x8, 2-pole matrix - it is also available in reed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PCI Very High Density Multiplexer, 99-Channel, 2-Pole
50-670C-022-99/2
Multiplexer Module
The 50-670C-022-99/2 is a 99-channel, 2-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Weather Stations (Paperless Recorder)
-
Is a data acquisition unit. It is designed for use with our ranges of meteorological sensors.
-
Product
PCI Very High Density Multiplexer, 24-Channel, 4-Pole
50-670C-021-24/4
Multiplexer Module
The 50-670C-021-24/4 is a 24-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
IC-3120, 1.91 GHz Intel Atom Quad-Core Processor, 2-GigE Port Industrial Controller
784959-01
Controller
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
Product
PXIe-6378, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781476-01
Multifunction I/O
PXIe, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6378 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6378 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Industrial PC
-
Get the dependability and precision you need for process control, data acquisition and more with Omron's advanced industrial PC offering.
