-
product
All-in-One Field Optical Tester
SMT-50
Power meter is the best essential tool for all technicians installing or maintaining optical fiber network. SMT-50 Multi Tester is made for the best performance of different parameters and demanding applications on fiber measurement. It is designed for handy size with simplicity and accuracy. SMT-50 provides 4 exquisite functions to optimize the time of all technicians and can be tested at up to 6 wavelengths in operating. Six main wavelengths (850, 1300, 1310, 1490 1550 and 1625 nm) used in FTTX networks can be tested of passive optical networks (PONs)
-
product
SpaceWire RMAP Tester
121
The SpaceWire RMAP Tester is a software test platform that provides the means to validate SpaceWire RMAP target implementations and to test the generic functionality of any unit that relies on the RMAP protocol for its configuration and control.
-
product
In-Circuit Testers
SPEA’s Bed of Nails Board Testers are scalable In-Circuit Test platforms that deliver the shortest test time, superior diagnostic accuracy, and extended test coverage for the most comprehensive range of electronic products.SPEA’s In-Circuit Board Testers are designed to increase yield, shorten the testing time, and cut the cost-of-test. Thanks to their unique Multi-Tester and Multi-Core Architecture, the SPEA’s Board Testers provide up to ten times greater throughput than conventional ICT test systems.
-
product
Rubber Durometer, Rubber Hardness Tester
LX-A
Shenzhen Chuangxin Instruments Co., Ltd.
LX-A Shore A Rubber durometer is widely applied in the low and medium hardness plastic, all kinds of rubber, multi-dimensional fat, leather, wax etc. The product conforms to GB/T531-1999 any other related standard.
-
-
product
Digital Leakage Current Tester
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
-
product
5KV Hipot Tester
RK2672
Shenzhen Chuangxin Instruments Co., Ltd.
5KV Hipot Tester is with high-precision and 1 year warranty.
-
product
Demulsibility Characteristics Testers
The Labodam Demulsibility Characteristics Tester is designed an dmade as per Test Methods for Demulsibility Characteristics of Petroleum Oils and Synthetic Fluids ASTM D1401
-
product
Digital Insulation Tester
DIT-1020
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT-1020 is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage of 100 Volts DC, its short circuit current is less than 500uA.
-
product
Medical Leakage Current Tester
2675Y
Shenzhen Chuangxin Instruments Co., Ltd.
The 2675Y Medical Leakage Current Tester Series Is The Test Equipment Used For Measuring Continuous Leakage Current And Patient Auxiliary Current Of Medical Electrical Equipment.It Designs And Products According To The GB9706.1_2020 (IEC60601-1:2012) .And The Test Circuit (MD)Input Impedance To Simulate The Body Impedance,It Accord With The Requirements Of GB9706.1-2020 (IEC60601-1:2012),The Test Current Can Run Up To 5A,And Provide Users With An Isolation Power Supply Which Adjustable Output Voltage For 0~250V Continuously Of The Basic Capacity Configuration For The 500VA And Provide Another 110% Voltage Source Of The Maximum Rated Voltage.It Can Satisfy The I,II, Various Types Of Equipment Test The Earth Leakage Current,Shell Leakage Current,Patient Leakage Current,Patient Auxiliary Leakage Current Under Normal Condition And The Single Fault.
-
product
Combo Tester
750
The ACL 750 Combo-Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. The ACL 750 can do what Pass/Fail testers cannot: Give actual resistance readings and store data. When the software is used, test results are stored on a computer which allows you to monitor and analyze test information and help manage your company?s static control program. Results can be stored from each test for up to one year in your computer.
-
product
Box Compression Tester
BCT-03
Jinan Leading Instruments Co., Ltd.
BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).
-
product
Flying Probe Testers
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
product
Modbus Simulator & Tester
Modbus Poll
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
product
Bench Mounted Tester
Flex 10
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
Digital (1kV up) H.V. Insulation Tester
6210A IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV)
Standard Electric Works Co., Ltd
Microprocessor-controlled. Four insulation test voltages. Insulation resistance; auto ranging on all ranges. Bargraph indicates test voltage; rise and decay can be observed during tests. Visual and audible warning if external voltage is present. Fully protected: crow bar. Carry case. EEPROM calibration.
-
product
Gas Chromatography Tester
Gas Chromatography Tester is designed to separate organic solvents. It is able to test solvent residues of printed packaging material, or the purity of a single solvent.
-
product
Field Sync Tester
Sentinel
All-in-one TesterPTP, NTP, SyncE and TDMMulti-port, simultaneous measurementsEmbedded GPS Rx and RubidiumHigh performance. Optional battery to maintain Rb in holdover during transit
-
product
DSE Wire Testers
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
product
LAN Cable Tester
21-6566-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
product
High Insulation Digital Clamp Tester
HCL-5000+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
product
Brake Fluid Tester For DOT4
6512A
Peaceful Thriving Enterprise Co Ltd
The tester can be used as a digital brake fluid tester suitable for determining brake fluid quality. Quality is tested and indicated on 5 LEDs in terms of "percent of water in the brake fluid". Develop for professional use in automotive repair shops and in servicing.
-
product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety. -
product
Semiconductor Testers
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
product
EV And Pack/Module Tester
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
product
Continuity Tester
4102
Peaceful Thriving Enterprise Co Ltd
This product is designed to measure the continuity of electric circuits and components. The measurement result will be indicated by LED and buzzer. The illumination is very helpful when technician is working in dark environment.
-
product
CT Burden Tester
585
The 585 Burden Tester is a hand held unit rated for use up to 20A. The design features a digital LED meter for displaying the current transformer (CT) secondary current. The burden is applied for a specific length of time controlled by circuitry inside the unit to help prevent the burnout of the burden elements.
-
product
Auto Contact Resistance Tester
KVHL
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
