Oscilloscopes
Analyze waveforms of electronic signals by producing a trace on a display screen of corrosponding oscillations of voltage and current.
See Also: Scopes, Fiberscopes, Microscopes, Borescopes, Endoscopes, Stethoscopes, Stroboscopes, Synchroscopes, Telescopes, Vectorscopes, Analog Oscilloscopes, Digital Storage Oscilloscopes, Oscilloscope Probes, Waveform, Digitizers
-
Product
Oscilloscope
RTM3000
Oscilloscope
Designed as daily problem-solving tool, the R&S®RTM3000 combines the power of ten (10-bit ADC, 10 times the memory and 10.1" touchscreen) with a Rohde & Schwarz probe interface for all Rohde & Schwarz probes.
-
Product
4 Channel Oscilloscope
2565B-MSO
-
The 2560B Digital Storage (DSO) and Mixed Signal Oscilloscope (MSO) Series offers 100 MHz, 200 MHz and 350 MHz bandwidth models in a 4-channel configuration, with a sample rate of 2 GSa/s and a maximum memory depth of 200 Mpts. Additionally, these oscilloscopes are equipped with a large 10.1" capacitive touch display that provide 1024 x 600 resolution and intuitive touchscreen gestures.
-
Product
PCI Express Oscilloscope Software Compliance Test
-
Rohde & Schwarz offers automated compliance test solution of PCI Express Gen 1.1, 2.0 and 3.0 interfaces. The test wizard of the Rohde & Schwarz ScopeSuite compliance test software guides the user via illustrated step-by-step instructions. The option supports add-in card and system motherboard testing. It is based on the PCI-SIG standard post processing analysis software and utilizes PCI-SIG test fixtures. A configurable test report documents the test results.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
SP500X , 500 MHz, ±300 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
783629-01
Oscilloscope Probe
The SP500X, or Multi-Contact Isoprobe IV - 10:1, is a standard passive probe with fixed 10x attenuation for oscilloscopes that provide 1 MΩ input impedance.
-
Product
Oscilloscope, 8 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8080HD
Oscilloscope
Oscilloscope, 8 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits.
-
Product
IEEE 802.3 CK Tx License Suite
SW00IECK
-
The IEEE 802.3 CK Tx License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation license for IEEE 802.3 CK (100/200/400 Gb/s). Together with the subscription model, this enables the support and coverage continuity as the IEEE 802.3 CK technology specification progresses through revisions.
-
Product
Digital Oscilloscope
-
Shenzhen Graigar Technology Co.,Ltd.
A digital oscilloscope is a complex electronic device composed of various software and electronic hardware modules that work together to capture, process, display and store data that represents the signals of interest of an operator
-
Product
WiFiScope WS5+SureConnect: 200 MS/s 250MHz BW, 2 Channel, Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
WS5-220XMS-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
Product
PXIe-5108 PXI Oscilloscope, 4CH, 14-Bit, 250MS/s, 100MHz, Oscilloscope With 256MB
790584-01
Oscilloscope
The PXIe-5108 oscilloscope supports high-channel-count signal acquisition for precise and flexible measurement applications. The PXIe-5108 provides eight simultaneously sampled channels, each with configurable coupling and voltage ranges to meet a wide range of test requirements. The PXIe-5108 offers multiple triggering options, substantial onboard memory for extended data capture, and a comprehensive instrument driver that helps streamline data streaming and analysis. The PXIe-5108 supports multichannel measurements with sampling rates up to 250 MS/s and analog bandwidth up to 100 MHz. The PXIe-5108 also provides advanced synchronization capabilities within PXI systems for coordinated measurements across instruments.
-
Product
ScopeCorder
-
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
Product
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV
RP4060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
4 Channel Oscilloscope
2569B
-
The 2560B Digital Storage (DSO) and Mixed Signal Oscilloscope (MSO) Series offers 100 MHz, 200 MHz and 350 MHz bandwidth models in a 4-channel configuration, with a sample rate of 2 GSa/s and a maximum memory depth of 200 Mpts. Additionally, these oscilloscopes are equipped with a large 10.1" capacitive touch display that provide 1024 x 600 resolution and intuitive touchscreen gestures.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
Test & Measurement Products
-
We offer a broad range of test and measurement devices for your scientific, educational, industrial, and process applications. We carry the test and measurements tools you need to analyze, validate, and verify measurements in your electronic and mechanical systems, ensuring compliance to quality assurance and quality control programs. Our selection features portable and bench oscilloscopes, multimeters (DMMs), clamp meters, megohmmeters, stroboscopes and tachometers, power transformers, along with precision meters for humidity, moisture, light, airflow, weather, and vibration.
-
Product
PXIe 500 MHz Oscilloscope
M9242A
Oscilloscope
500 MHz bandwidth oscilloscope2 analog channels5 GSa/s sample rate1,000,000 wfms/s update rate Isolate signals in seconds with exclusive zone triggering Additional options: 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis and mask testing
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Digital Storage Oscilloscopes
SDS1000CML+ Series
-
SDS1000CML+ series is a dual-channel universal digital oscilloscope, available in 70, 100, and 150 MHz bandwidth models. It includes a 2 Mpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7-inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
Product
4-Ch Digital Storage Oscilloscope
2553
-
The 2550 Series digital storage oscilloscopes deliver performance and value in 2-channel and 4-channel configurations. With bandwidth from 70 MHz to 300 MHz and 2 GSa/s sample rates, these oscilloscopes offer 24 kpts/Ch waveform memory, 32 automatic measurements, and advanced triggering capabilities including math functions. Engineered to allow you to see more of your signal under test, the 2550 series’ widescreen 7” TFT display offers a significantly larger viewing area than typical economy oscilloscopes (5.7”).
-
Product
4 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 404HD-MS
Oscilloscope
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
WiFiScope WS6: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XM-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
Product
Portable Mixed Signal Oscilloscope
2 Series MSO
-
Unlock more space on your bench without compromising performance by choosing our most compact and portable oscilloscope. At only 1.5 inches thick and less than 4 pounds, the 2 Series MSO feels like a tablet while offering the full-featured functionality of a realtime touchscreen oscilloscope. On the benchtop, in the classroom, or to the field, take it wherever your measurement challenges take you.
-
Product
Keysight Streamline Series P9243A USB Oscilloscope
P9243A
Oscilloscope
Compact, faceless, USB oscilloscope using Keysight’s InfiiniVision technology. Available at 1 GHz and 5 GSa/s. Offers a small footprint and mobility.
-
Product
Handheld Oscilloscope
ScopeRider
Oscilloscope
When debugging embedded devices in the lab or analyzing complex problems in the field, the R&S®Scope Rider offers the performance and capabilities of a lab oscilloscope as well as the form factor and ruggedness of a battery-operated handheld device. Isolated channels combined with 500 MHz bandwidth makes it a perfect choice for power electronics applications. An integrated multimeter (two-channel model) or a multimeter mode (four-channel model) make the instrument the perfect tool for troubleshooting all kinds of electronics problems.
-
Product
O-E PROBE
-
O-E probe is the unit to convert optical signals to electrical signals. It can be connected to Oscilloscopes or data loggers via a BNC connector and monitor the conversion waveform. It can acquire the optical signal easily by just pointing the optical fiber probe at the light source. Recently, more and more light sources utilize optical modulation for next generation lighting such as LED. Acquiring the emission timing is required to measure the emission phenomenon of the light source. This O-E probe unit is the ideal tool for these tasks.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI Dual 8 to 1 Mux 1GHz 75Ohm 1.0/2.3 Con
40-748-731
Multiplexer Module
The 40-748 is a dual 8 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-748 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
500 MHz, 1.0 pF Active Differential Probe
ZD500
-
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
