Signal Conditioning Systems
-
product
Signal Pylon Blocks
40 POL low resistance pylon, 40 POL signal pylon, 85 POL signal pylon, 102 POL Signal Pylon, 136 POL signal pylon, 170 POL low resistance pylon, 170 POL signal pylon, high current pylon blocks, optical pylon blocks, pneumatic pylon blocks, radio-frequency pylon block, & usb pylon blocks
-
product
Electrical Signal Test
High-density, multi-channel pulse pattern generators and bit error detectors for the design, characterization and production test of optical transceivers and opto-electrical components.
-
product
Signal Conditioners
Macom Technology Solutions Holdings Inc.
At MACOM we offer the industry’s largest portfolio of crosspoint switch devices with channel counts ranging from 2x2 all the way up to 288x288, and data rates from 3.2 Gbps to 28 Gbps. Our devices are equipped with signal conditioning technology that enables system designers to use lower cost board materials and components while increasing their system margin.
-
product
Single Channel Signal Buffer Module
Alliance Support Partners, Inc.
Signal quality problems caused by mismatched impedance can result in intermittent measurements and faulty diagnostics. This is most often observed when transporting a test program from one system to another, such as re-hosting it from an older generation system to a new one. The primary root cause of the impedance mismatch is the signal path from the UUT to the measurement instrument. The switching system technology often is responsible for much of the distortion. The Signal Buffer Module (SBM) is designed to receive a signal from the UUT with high impedance output and accurately reproduced it at the output for delivery to the measurement instrument. The SBM output matches the 50 ohm input impedance of most measurement instruments and result in significantly reduced signal distortion.
-
product
Signal & Power PCB Connector
HPW Series
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
product
Telemetering System
ZET 7172
ZET 7172 telemetering system is used to provide wireless access to the instrument line segment using radio channel.
-
product
Transmitter System for Low Signal Power Relay Stations
AM3000 Series
Japan Communication Equipment Co., Ltd.
This system is a minimal low signal power transmitter for the relay of ISDB-T Digital Terrestrial Broadcasting. As the need arises, it's possible to have the compensation function built-in for integrate-type basic equipment.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
Optical Systems
Optical systems like optical objectives or oculars are a crucial block of modern electro-optical systems. Performance of these systems is often limited by parameters of optical block. Superior optics can significantly increase surveillance ranges of electro-optical surveillance systems like thermal imagers, VIS-NIR cameras, SWIR cameras, and night vision devices. Optical systems in form of optical sights are also used as independent systems in surveillance technology.
-
product
20 GHz Signal Source
VCO Series
The SC5510A and SC5511A are VCO-based, synthesized signal sources with very low phase noise and an amplitude control of 0.01 dB throughout its -30 dBm to +15 dBm output power range. By utilizing a unique multiple phase-locked loop architecture, phase spurs are kept below -70 dBc across the entire tuning range, even at 1 Hz step resolution. Download the data sheet to see how the impressive features and specifications of these modules make them stand out when compared to other small modular synthesizers. These 20 GHz signal sources include an additional, independent RF2 channel with a tunable frequency range from 100 MHz to 3 GHz and a tuning resolution of 25 MHz. The extra channel makes the modules suitable for either single-stage RF conversion systems or dual-stage image suppression up/down converter systems. Both modules make great general-purpose laboratory signal sources where demanding low phase noise and signal purity are required. They are both ideal choices as an integrated clock source for fast DAC and ADC applications, especially those that require variable sampling rates. Full implementation instructions, GUI, driver software, and example code are provided with each module.
-
product
System Amplifier
Solid state Broadband Amplifiers are designed for optimum operation for IED Jammer Applications which is featured as below. We can rack mount any of our existing amplifiers or systems or custom design the amplifier and enclosure. Each Rack Mounted Amplifiers are built around a large bonded fit heat-sink rated for high temperature ambient operation.
-
product
Vibration Signal Converter
High performance and low costSmall size, attachable with DIN railSwitchover Measurement Mode, switchover Measurement Range●Acceleration / Velocity / H Function / H Function CF *（only for VM-80DA)●Velocity / Displacement (VM-90 DV / DVL)Substantial basic functionsOne step alarm outputDC4 ～ 20mA level outputAC±5V monitor outputLevel indication
-
product
Signal Generator Software
The software solutions for the class-leading signal generators from Rohde & Schwarz support various demanding applications. These include powerful radar simulation, the generation of digital I/Q signals supporting various radio standards as well as software tailored for multi-channel vector signal generator setups.
-
product
CATV Multi Carrier Signal Generators
5112
The 5112 is a portable RF signal generator, available in four or six carrier configurations. Each carrier can be activated individually or simultaneously.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Source And Measure WiFi And Bluetooth Signals
IQview
The LitePoint IQview® simplifies WiFi and Bluetooth® device development with powerful tools to both source and measure WiFi and Bluetooth signals and analysis capabilities providing insight into device behavior. The IQview offers seamless compatibility with the IQflex® manufacturing solution enabling test software developed on the IQview to run on the IQflex platform widely deployed in manufacturing environments.
-
product
Signal Analyzer
Choose from an extensive selection of signal analyzer products from DC to 44.5 GHz and extendable to 325 GHz.With excellent total level accuracy, dynamic range and performance, Anritsu spectrum/signal analyzers not only can capture wideband signals but FFT technology supports multifunction signal analyses in both the time and frequency domains. Moreover, the built-in signal generators on some models outputs both continuous wave (CW) and modulated signals for use as a reference signal source.
-
product
Digital Signal Splitters
Advanced Science and Novel Technology, Co., Inc.
High-speed broadband Data/Clock Amplifier and DistributorExhibits low jitter and limited temperature variation over industrial temperature rangeOne input differential signal port and two differential amplified output signal portsMatched phase delays for all outputsFully differential CML input interfaceFully differential CML output interfaces with 600mV single-ended swingSingle +3.3V or -3.3V power supplyPower consumption: 560mWFabricated in SiGe for high performance, yield, and reliability
-
product
Etch System
When it comes to clean etches, Veeco’s Ion Beam Etch (IBE) systems deliver with sharp control and minimal disruption. Using a focused argon ion beam, this subtractive technique etches nanoscale features with precision, making it a go-to for pattern transfer, layer removal, and surface refinement where edge definition matters most.
-
product
Assembly Systems
Easily add automation to your assembly process. Free operator hands and eliminate the need to manually handle screws. The A-50 units are modular...a simple rail change and readjustment are all that are necessary to use a variety of screw sizes.
-
product
Signal Conditioners / OEM Boards
Signal conditioners and OEM cards that can be integrated into your system.
-
product
Cooling Systems
Aerodyn Engineering designs and manufactures its own line of cooling carts. Our cooling carts will supply filtered coolant to the slip ring while in operation. Aerodyn Engineering’s cooling units are extremely reliable and are designed and manufactured with the highest quality components and craftsmanship available in the industry today. Magnetically coupled pumps are employed within our system to deliver the cooling fluid, with full user instruments showing flow rate and system pressures.
-
product
Interferometer Systems
Verifire Series
The Verifire™ interferometer system provides fast and reliable measurements of surface form error, and transmitted wavefront of optical components, systems and assemblies.
-
product
Standard Signal Isolating Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
product
Signal Level Meters
Wuhan Sunma Technology Co., Ltd.
Signal Level Meter is specially designed and manufactured for CATV system installation and testing. It‘s a portable instrument, easy to carry with many functions.It can test CATV signal level both at channel and frequency mode. Also it can measure CATV TILT,C/N, trunk cable Voltage, ect. The big character TN LCD clear1y displays all testing results. It especia1ly fit for CATV station as a professional measurement instrument. it can display 2 channels at the same time.
-
product
Test Systems
Testing is more than just finding defects on Printed Circuit Boards. It is also about how to predict defects before they occur. A true economy can only be achieved when you see testing as an integrated part of manufacturing. To achieve this we provide Advanced Diagnostic Tools and Electronic Manufacturing Systems (EMS) that integrate testing with design, manufacturing, and repair.
-
product
RF Systems
With our detailed, end-to-end knowledge of beam generation systems and the way platforms operate in the field, we deliver state-of-the-art radio-frequency and x-ray systems. These integrated and effective systems are built with optimised components and interfaces to achieve the performance, reliability and ease-of-use expected by platform designers, manufacturers and end-users.
-
product
Signal Optimizer Software
A unified software package for calibration, signal creation and analysis.
-
product
Impulse-Calibration-System
KAL1000 Series
The impulse calibration system KAL1000 is a modular system to perform tests on complete impulse voltage measuring systems and on digital recorders for the measurement of high impulse voltages and impulse currents. The modular design allows an optimal KAL-configuration depending on the actual application.Additional, this modularity allows to up-grade or modify and existing KAL1000 system in case of changing or additional requirements
-
product
ATE & Test Systems
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
