Signal Conditioning Systems
-
product
Automatic Power Control system
The Automatic Power Control system cuts the incoming power supply to a traction unit for short periods. This is required where power supplied from one part of a power distribution system in separated from another by a neutral section. Its fitment prevents damage to the power distribution system or the vehicle.
-
product
Display Test System
PIMACS provides the broadest range of display optical performance measurement system for optical testing of various samples including flat panel displays. We are specialized in testing all sizes of display modules and panels ranging from various field.
-
product
Integrated I-V Test Systems
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
product
Universal Checkback Standalone System
UCBS
The Universal Checkback Standalone System (UCBS) provides periodic testing of "ON-OFF" carrier sets other than the TC-10B and the UPLC/UPLC-II (which incorporate this same checkback tester internally). The UCBS determines the functionality of the complete channel including the transmitters, receivers and associated coupling equipment. Periodic testing is required for the normally "off" channel, to provide warning of signal deterioration prior to needing it for relaying, The UCBS facilitates automatic testing of the channel at preset intervals. The UCBS is totally field programmable. All programming is done with a computer using the RS232 serial port or limited factory settings with switches on the Checkback module. Front panel LEDs indicate the factory or custom setting applied and the status of alarms.
-
product
Hall Effect Measurement system
HMS-5500
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
product
Partial Discharge Measurement System
DAC-6021
DAC-6021 is a measurement system for testing Partial Discharge of high frequency equipment, power devices, stator coils, etc.Since the system combines Partial Discharge Measuring Instrument (DAC-PD-3) with Testing Corona-free Variable Frequency Voltage Source (DAC-WT-50) and Testing Shielded Chamber, most external noises are removed, and the measurement is safe.
-
product
Lifecycle Test System
Model 933
The Model 933A Life Cycle Test System is a low cost, generic test platform used to perform cycling of keypads, keyboards, membranes, switches, or any product requiring fatigue testing.
-
product
Programmable Video Signal Generator
VG-871B
The VG-871B is a standalone type multiple-interface video generator, which can test most of Flat-Panel-Display in current market. It supports the HDMI digital interfaces with the latest standard Ver.1.3a, and also supports specific functions of HDMI 1.3a such as Deep Color (max.12-bit), xxYCC and LipSync
-
product
Blackbody System
IR-2103/301
Infrared Systems Development Corp.
Infrared Systems Development introduces a NEW Low-Cost Thermo-Electrically cooled / Heated blackbody source. The 0.375" Thick solid Copper Emitter plate provides superior uniformity and energy emission. Our Proprietary High Emissivity Black Coating provides >0.95 uniform Emissivity from 0.8 to 30 um.
-
product
Systems for Water Leak Detection
Here you are getting an overview about our devices for water leak detection. In our portfolio you can find systems for electro-acoustic water leak detection, compact onehand receiver, correlators, stationary noise loggers and a lot more...
-
product
Charge System Safety
Renesas' charging system safety circuits are optimized to provide a redundant safety protection to an Li-ion battery charging system by monitoring input voltage, battery voltage and charge current.
-
product
Sampling System
ASS-370
The sampling unit is responsible for suction air from ambient and to distribute this air without any changing to the gas-monitors. The HORIBA sampling unit is designed according ÖNORM-M5852 Type A. So an air flow monitor will give alarm information when the flow is to low.
-
product
Collision avoidance systems with radar
With OndoSense radar sensors for collision avoidance, obstacle detection and positioning, you ensure safe, accident-free and productive vehicle operations. Our robust anti-collision sensor is suitable for trucks, mobile robots, drones, ships, aircraft or other vehicles and detects obstacles with great reliability.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-02
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
System Module
CM AXIe-0
CM AXIe-0 is intended for use as part of AXIe-0 standard racks with the number of slots (slots) no more than 14. CM AXIe-0 meets the requirements of the AXIe-0 standard for system modules of the AXIe-0 trunk.
-
product
Test Cell System
qCf FC25/100
The quickCONNECTfixture with an active fuel cell area of 25 cm 2 has been an integral part of our product portfolio since 2006. The excellent properties and the patented design of the cellFixture offer enormous advantages in the characterization of cell-internal components for fuel cells and electrolysis.
-
product
System Modeling
Mentor Graphics SystemVision is a mixed-signal modeling and simulation environment using the power of VHDL-AMS and SPICE to verify your control and mechatronic systems. SystemVision includes graphical design entry, VHDL-AMS modeling and library tools, leading-edge simulation technology and powerful waveform viewing and analysis tools
-
product
Pressure Comparator (System F)
Type T
AMETEK Sensors, Test & Calibration
Type T hydraulic comparator (System F) is a self-contained high volume pressure source capable of producing pressure up to 15 000 psi. It is ideal for testing gauges and setting hydraulic relief valves and pressure switches. Multiple models are available for hydraulic oil, water, or both.
-
product
Motor Drive Test Systems
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
product
Water Quality Monitoring Systems
We provide instrumentation, test kits, and chemical reagents used for monitoring water quality in a variety of applications. Primary applications used within our industry include drinking water, wastewater, and ballast water.
-
product
Flexible Data/Analog Switching System
S6025DE
Universal Switching Corporation
Designed for parallel switching of RS-232 data or other similar types of data, the S6025DE delivers compact solid-state switching in an expandable configuration. The unit can start as a smaller size and be expanded later to a full 60x60 array with 25 levels, perfect for switching RS-232 type data. It provides a choice or a combination of remote control including RS-232C, RS-422A, RS-485, GPIB (IEEE-488) and Ethernet (10base-T).
-
product
QE System
PVE300
The PVE300 system is a monolithic,turnkey solution for photovoltaic material and device characterization;a key component in research, or as part of a production-line quality process.
-
product
Pulsed-DC Systems
Extend process innovation with Advanced Energy’s comprehensive pulsed-DC suite. Minimize arcing, enhance deposition rate, improve film flatness and packing density.
-
product
Gunshot Detection & Localization System
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
product
FPGA Signal Processor
377
The Model 377 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
product
Signal Processing Hardware System
MONARCH
From solar-powered Atom boards to 4U rack mount servers, 3dB Labs engineers the right hardware solutions for the right mission. Our MONARCH (MONitor and ARCHive) systems are available off the shelf for a variety of scenarios: lab or ruggedized, remote or local.
-
product
Dynamic Signal Analysis
m+p Analyzer is a fully integrated solution for dynamic signal measurement, analysis and advanced reporting of all noise and vibration, acoustics and general dynamic signal applications. Comprehensive time and frequency analysis is available with both online and offline data processing. Complete with advanced application wizards the m+p dynamic signal analyzer makes light work of gathering data, displaying results, performing specialized analysis and generating customer ready reports – all within one user interface. m+p Analyzer is designed for noise and vibration applications in the field and in the lab.
-
product
"Signal Transporter"
LTX-5525
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
product
OTA Chamber for 5G NR mmWave Signals
ATS1800C
The R&S®ATS1800C CATR based 5G NR mmWave test chamber provides the ideal environment for testing 5G FR2 antennas, modules and devices over the air (OTA) from R&D to conformance. With its small footprint and wide frequency range, the R&S®ATS1800C offers great functionality and test coverage in a very small space. With its flexibility and broad range of extension options, the R&S®ATS1800C offers a solid and future-proof environment for your FR2 testing needs.
-
product
Analysis System
Pegasus (EDS-EBSD)
The Pegasus Analysis System enables the simultaneous collection of Energy Dispersive Spectroscopy (EDS) (chemistry) and Electron Backscatter Diffraction (EBSD) (crystallography) data, allowing direct correlation between the elemental content and microstructural aspects of the material being studied.
