Tuners
Adjusts a signals frequency to one frequency or band of frequencies.
-
Product
Antenna Tuners
DU-3000T / DU-3000TB
-
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
Product
Slide Screw Tuners
-
Slide screw tuners are particularly suited to establishing impedances for device characterization, or for any other application requiring a precisely repeatable mismatch condition. This is due to the precision with which a specific matching condition can be repeated if the tuner has calibrated position indicators.
-
Product
Automated Tuners / Impedance Tuners / Load Pull Tuners
-
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
Product
LXI-Certified 1.85mm Automated Tuners 8.0 to 65.0 GHz
MT985 Series
-
Maury''s MT985AL01 LXI controlled automated tuners are optimized for a broad class of in-fixture and on-wafer applications requiring flexibility, broad frequency coverage and ease of use. Based on Maury''s proven non-contacting probe technology, these high-performance tuners evolve beyond outdated contacting probe technology to deliver high VSWR with superb accuracy and reliability.
-
Product
Manual Tuners / Impedance Tuners
-
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
Product
Broadband Tuners
BT1500A
-
The BT1500A 1500 watt balanced antenna tuner is the only 1500 Watt, Double-L Network antenna tuner on the market today covering 20m to 160m (2500+/-j2500) and 10m - 15m (1000+/-j1000). The BT1500A features two tandem mounted, precision ceramic roller inductors for a truly balanced tuner.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
Product
Frequency Multipliers
Triplers
-
*No mechanical tuners*fullband operation*planar design*zero Bias
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
FTTH Optical Node
SFT3908
-
Hangzhou Softel Optic Co., Ltd.
- Support 8 tuners (DVB-S/S2/S2X) input; 1 U chassis optional for 1/2/3 cards maximum for 8/16/24 tunerinput; Each tuner card are working independently with its NMS and 1 GE Data port - 8 MPTS (8MPTS out thru bypassing) under Passthrough mode over UDP/RTP thru Data port,unicast/multicast-Version 1 -2 MPTS out after multiplexing or 512 SPTS out switchable under Mux mode over UDP/RTP thru Data port, unicast/multicast-Version 2-Up to 256 PIDs remapping per output channel(Mux mode only) - Support PID re-mapping and pass-through(Mux mode only) - Support Diseqc function(Mux mode only) - Support Biss decryption, each tuner support maximum 64 BISS key decryption (Mux mode) - Web-based NMS management
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
Product
Amplifiers
LA-1K
-
Introducting the new LA-1K RF Sensing Dual HF LDMOS 1000 Watt Amplifier. While the LA-1K will work with a wide variety of tuners and transceivers, Palstar custom-designed the LA-1K to work as the perfect match for our very popular HF-AUTO autotuner. MADE IN THE USA
-
Product
Multiplexer
SFT3107G
-
Hangzhou Softel Optic Co., Ltd.
SFT3107G Tuner Input Multiplexer is the latest demodulation and multiplexing device for digital TV broadcasting head-end system with TS output through IP port. It can multiplex up to 16 channels Tuner and 2 ASI input to IP (MPTS). This multiplexer has the functions of supporting auto-generation of PSI/SI information, PID re-mapping, and service filtering.
-
Product
Automatic Antenna Tuner
-
Automatic Antenna Tuner has not been released for full Beta testing and production yet as we are solving some firmware issues. We cannot give you a date nor estimate at this time when full production will commence.
-
Product
Arbitrary Load Control For Modulation Distortion
S94570B
-
Extend the modulation distortion application by computing figure of merits such as EVM and ACPR for any desired load with arbitrary load control (ALC). Modulation distortion with ALC integrates the powerful capabilities of the PNA-X with an electromechanical tuner so a non-50 Ω load can be presented to the DUT and changes in device performance or sensitivity to varying load conditions can be accurately measured.
-
Product
Narrow Band Multiplier
-
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
Product
Talon 8 Channel 6 GHz RF Rugged Rackmount Recorder
Talon RTR 2628
-
- Eight-channel phase-coherent RF recording- Ideal for signal intelligence, phased-array radars, beamforming, and DF (Direction Finding) systems- Records RF frequencies from 30 MHz to 6 GHz- Captures 80 MHz of instantaneous bandwidth- Eight-channel RF tuner can be set for phase-coherent operation or independent tuning- Eight 250 MHz 16-bit A/Ds- Eight DDCs with decimations to 65,536 for selectable bandwidths- 3.2 GB/sec real-time aggregate recording rate- 4U 19-inch rugged rackmount PC server chassis- Windows® workstation with high performance Intel™ processor- Front panel removable SSD drives- Up to 122 terabytes of storage to NTFS RAID disk array- SystemFlow® GUI with signal viewer analysis tool- Optional GPS time and position stamping
-
Product
Frequency Multipliers
Doublers
-
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
Product
Antenna Tuner
DU-1500T
-
The DU 1500T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching.The DU1500T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indicted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Antenna Tuner
DU-3000T/DU-3000TB
-
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU-3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
Product
Manual Tuners
-
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
Product
MFJ Dummy Load/Wattmeter
MFJ-267
-
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
Product
Antenna Tuner HF+6m
DU 800 T
-
The DU 800 T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 800 T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indiceted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
Modulator
SFT3348C
-
Hangzhou Softel Optic Co., Ltd.
SFT3348C is a high performance and cost-effective DVB-C modulator designed by Softel. It has 8 DVB-S2 tuner inputs, after multiplexing, scrambling and modulating process, then it gives 4 RF output. To meet customers’ various requirements, this device is also equipped with 128 IP input and 4 MPTS output over UDP and RTP. Its pluggable structure design greatly facilitates the change of modules as needed. Moreover, the four CAMs/CIs accompanied can descramble the programs input from 8 Tuner inputs. SFT3348C can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and very adaptable to newly generation CATV broadcasting system.
-
Product
L-Band RF Tuner, 2-Channel 200 MHz A/D, Virtex-6 FPGA - x8 PCIe
Model 78690
-
Model 78690 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A 2-Channel high-speed data converter, it is suitablefor connection directly to the RF port of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D
Model 78891
-
Accepts RF signals from 925 MHz to 2175 MHz, Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm, Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
-
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
