Control Software
-
product
Multi-Functional Board
PCI - HARPOON
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
product
Digital I/O Board
P104-DIO-96
Each I/O line of this card is buffered and capable of sourcing 32mA, or sinking 64mA. The board simulates Programmable Peripheral Interface chips (PPI) to provide a computer interface to digital I/O lines. Each PPI supports two 8-bit ports (A, B) and two 4-bit ports (Chi, Clow). Each port can be configured to function as either input or output latches. The I/O line buffers (types 74ABT240 and 74ABT245) are configured automatically by hardware logic for input or output according to the PPI Control Register direction software assignment.
-
product
Compact LCR Meter
TH2832
Changzhou Tonghui Electronic Co., Ltd.
Adopting the latest technology & high density circuit design and concentrating the essence of LCR test, TH283X series is a new generation compact LCR meter of low cost and high performance. Instead of traditional mechanical power switch, it adopts software control power switch. The basic accuracy of 0.05% and good test stability can compare favourably with those high-end models. Being equipped with
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
8U 21 Slot VME64/64X Enhanced Crate
VME8100
short circuit protection, Over / Undervoltage protection, Over temperature protection. Remote monitoring and control take place through CAN bus, Ethernet, USB and RS232 interfaces. The crates are also SBC controlled via graphic OLED Display, provides Automatic Daisy Chain and supports Chained Block Transfers (CBLT). User-friendly control software completes the VME 8100 features. The Unit is powered by 92 ÷264 Vac, 50 ÷ 60 Hz, power factor 0.98% (230VAC).
-
product
Software
TSR Control
Diversified Technical Systems, Inc.
TSR Control is the user-friendly set-up, control and viewing software for the entire line of TSR data loggers. An intuitive interface makes it easy to configure the recorder, view real-time sensor output and review time-history data. Via a PC, users can set the record time (seconds), trigger threshold (g) per axis, and download individual or multiple events stored in flash memory. TSR Control also includes tools for zoom, filtering and Head Injury Criteria (HIC) calculations.
-
product
Software
CAEN Software - readout software, open FPGA tools, configuration tools, control software, EASY configuration files, EPICs, LabVIEW Instrument Drivers, and more.
-
product
Thickness Tester
CX-Series
The Thickness Tester - CX-1000 combines our patented capacitance sensor with industry-leading software to give you plastic film thickness profiling resolution to one micron. This gauge can be run as a stand-alone bench unit, or can be connected to a computer for RS-232 operation by our Thickness Tester - CX-1100 Quality Control Software. Capacitance measurement is industry-recognized as the best choice for off-line, high resolution, continuous gauge profiling for plastic films.
-
product
RF Test and Measurement Solutions
Signal GeneratorsSwitch MatricesProgrammable AttenuatorsControl ProductsSignal MeasurementModular Test SystemsCustom Test SystemsUser-Friendly Control Software
-
product
Software Development Projects
Precision Development Consulting Inc
Automation of new process tool prototype in startup environment, Complex R&D Gasbox Automation, Semiconductor System Control Software, Wafer Transfer Control Software, 300mm Factory Automation, Complete port of Spectrometer software to windows, HSMS Protocol
-
product
Digital Interface
DNTBOB-88
BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.
-
product
Self-Discharge Analysis Software
BT2155A
The Keysight BT2155A self-discharge analysis software, controlling the BT2152A or BT2152B self-discharge analyzer, measures and records Li-Ion cell self-discharge current and cell voltage. The software configures the analyzer’s channel settings, such as initial voltage and current matching, channel limits (OVP, OCP, UVP), measurement intervals, and test duration.
-
product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
product
Dual Channel MIL-STD-1553 BC/RT/MT cPCI Intelligent Module
DP-cPCI-5664
The DP-cPCI-5664 provides new level of performance and flexibility for MIL-STD-1553B notice 2 in a Compact PCI form factor. It has full intelligent interfacing between a cPCI bus and one / two independent dual redundant MIL-STD-1553B data buses. The 1553B bus functions are fully controlled by a DSP processor. Software controls the operation of the channel as either a 1553 Bus Controller (BC), Remote Terminal (RT), or Bus Monitor (MT).
-
product
High-Density Matrix Switch Card
1260-43
The Astronics 1260-43 is a high-density matrix switch card. Each module consists of three 8x24 single-wire matrices, which are interconnected via a 10-lane, single-wire bus. On-board configuration relays allow software control of the matrix configuration.
-
product
Automation Controllers And Modules
Our complete automation platform solution along with a suite of automation control hardware and software configurable modules allow semiconductor and other industrial manufacturing customers to better automate their processes through computer-controlled automation and seamlessly integrate with existing MKS products to provide a complete solution.
-
product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, Type-N, 2 Port
85092D
The Keysight 85092D RF electronic calibration (ECal) module makes calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
product
Vacuum Process And Chamber Environment Monitors
Our process monitors are innovative in-situ process monitoring instruments that are fully integrated, application-specific packages, including component residual gas analyzers (RGAs), analytical equipment, and control software. Process mass spectrometers are used in varied applications, including; Semiconductor, Thin Film (CVD, Etch, PVD and degas), pharmaceutical lyophylization and bulk gas purity monitoring.
-
product
Gavia AUV Software and Data Handling
The Gavia autonomous vehicle control software is implemented using a 'crewmember' paradigm. This means it is organized using a distributed architecture modeled on the division of responsibilities among the crew of a marine vessel. The Gavia Intelligent Artificial Crew (IAC) comprises a full set of modules responsible for the safe navigation of the vessel together with project modules responsible for meeting the goals of the mission. The Captain has the a set of responsibilities suitable for the role; overseeing the operation of the vessel and deciding on actions in response to exceptional or critical circumstances. With the vehicle Captain handling reaction to exceptional circumstances, the application modules are free to concentrate on the goals of the mission.
-
product
MEMS-Scanner Evaluation-Kit
The "QSDrive Scan Kit" evaluation kit enables small and medium-sized companies in particular to operate ResoLin components from the Fraunhofer IPMS in accordance with the specifications without the time-consuming in-house development of control electronics. The evaluation kit consists of a ResoLin component – a cardanic MEMS scanner with a linear axis and an optional, orthogonally oriented resonant axis – and control electronics that enable the components to be operated with an optimized trajectory supplied. The component is held by a scan head, which is also included in the scope of delivery and which, thanks to its special construction, can easily be integrated into common optical test setups. Depending on the design of the MEMS component, controlled operation of the component and synchronized operation of the resonant axis are also possible. The function is controlled by software that communicates with the electronics via USB.
-
product
LXI Wideband Scalable Matrix
Pickering's LXI wideband scalable matrix (model 65-110A) offers you a solution that can be easily reconfigured by the removal and insertion of sub-cards. The product is purchased as an assembled chassis, baseboard and the quantity of plugin modules initially required. As your requirements evolve additional modules can be easily fitted and the control software automatically detects the new configuration.
-
product
Real-time Hardware Interfacing Package
VISUALCONNX
VISUALCONNX is a visualisation and control software product, allowing real-time hardware or software interfacing, monitoring and logging.
-
product
Chamber Controllers & Software
Designed off of our previous controller platform with familiar features in an improved interface, added functionality for ease and fewer steps to accomplish your daily testing needs. Remotely monitor and control your chambers and receive text/email alarms. From the home screen users can now manually control, run or stop a profile and view a snapshot of current activity like actual/setpoint values, alarm, datalogging, profile, security, IP address information and more.
-
product
Single-phase Relay Test Set
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations. It is further necessary that these expanding testing capabilities be met with a similar improvement in the simplification of a test instrument’s user interface and software control.
-
product
Vacuum Systems
Custom vacuum systems, and retrofits into existing systems, are also available.Electrogrip has extensive in-house and customer system design experience ...Mechanical, flow, and thermal simulation;Mechanical design and fabrication;Software system automation.DepEtchPro control software permits rapid automation, without programming:Process systems and robotic motion control are automated with job files and icon setup.Always under user control, hence permitting unlimited field upgrades.
-
product
LXI Wideband Modular Matrix Chassis
65-110A-001
This module matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of sub-cards. It is purchased as an empty chassis with a baseboard and quantity of sub-cards initially required. As your requirements evolve, additional cards can be easily fitted. When new cards are added, the control software automatically detects the new configuration.
-
product
Schematic Learning System
RevEng
RevEng offers an effective method of creating professional quality circuit diagrams from a sample board. The RevEng system comprises a PC controlled continuity measuring hardware system, RevWin control software and EdWin, a fully featured CAD package.
-
product
Embedded Peripherals
Elsoft’s Embedded Peripherals Systems Group has more than 10 years' experience designing, developing and integrating embedded systems. With a comprehensive portfolio of turnkey embedded systems, embedded platforms, PC based I/O modules, motion controllers and software products, and engineering services, the Group supplies innovative technologies to OEMs and automation enterprises worldwide.
-
product
Software
Besides the primary WITE32 Test Environment package at the heart of our spinstand-based test systems, Guzik offers a variety of software options to provide additional measurement accuracy and analysis. Control and Automation software enhances various electro-mechanical capabilities of the test system (such as servo accuracy), and the available suite of Analysis software tools provides deep insight into the drive component under evaluation. Adjacent Track Interference, 3D Pulse Profile, Media Scanning and Bit Error Rate are examples of some of the optional additions. Some software tools require the WDM5000 Waveform Digitizer to be part of the overall test system.
-
product
VME – NIM Power Supplies
VME solutions are an integral part of CAEN’s design history. CAEN VME solutions for Data Acquisition and Front End applications have been part of were first developed decades ago. These solutions have been upgraded and modernized multiple times, and were recently joined by CAEN VME programmable High Voltage Boards. Thanks to the innovative GECO2020 Control Software, and the multi-master capability of CAEN VME Bridges, it is now possible to accommodate and independently control an integrated VME DAQ/HV System.
