PCI Express
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller. Also known as: PCIe
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, Serial ATA, Serial Peripheral Interface, SMBus, PCI Express Test, PCI Express Analyzers, PCIe
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCIe 5.0 Protocol Analyzer
P5552A
Protocol Analyzer
The Keysight P5552A PCIe 5.0 Protocol Analyzer introduces a new form factor that is easily deployable in the lab bench environment to enable deep protocol analysis of a PCIe system with unparallel signal integrity. Locate protocol errors or validate device operations by viewing data from the physical layer all through the transactional layer with ease.
-
Product
Mini-ITX 12th/13th/14th Gen & And Series 2 Intel® Core™ Processor LGA1700
AIMB-279 B1
-
Intel® Core™ Desktop Processors 12/13/14th Gen and Series 2Dual channel DDR5 5600MHz, max. 96GB with two SODIMMsSuper Speed I/O: PCIe x16 Gen4 (16GT/s), USB3.2 Gen2 (10Gbps), 2.5GbEQuad independent 4K displays with 2 DP1.4, 1 HDMI, and 1 LVDSRich expansion: M.2 M key for NVMe SSD, M.2 E key for wireless, 2 SATA12-24V DCin Power Input via ATX 8pin+5VSB pin headerWindows 11 LTSC & Ubuntu 22.04 LTS; SUSI API and WISE-DeviceOn
-
Product
x1 PCI Express System Timer
SKU-048-01
-
The x1 PCI Express System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The Timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the x1 PCI Express System Timer supports clock intervals ranging from 1ms to 64ms.
-
Product
PCIe Thunderbolt 3 EON Express 12-Bit Digitizers
Thunderbolt 3
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
Mini-ITX M/B Support 12th/13th Gen Intel® Core™ Processors, H610E, 3 X LAN For PPC-600
PPC-MB-620
-
Supports Intel® 12/13th Gen Core™ i processor (LGA1700) with Intel Q670E/ H610E chipsetTwo 262-pin SO-DIMM up to 64GB DDR5 4800 MHz SDRAMSupports triple display of DP/HDMI/LVDSSupports PCIe x16 (Gen 5), 1 x M.2 M key & 1 M.2 E key, 6 USB 3.2Supports 2 x SATA 3.0 (Raid 0, 1) (only for PCH Q670E)Supports TPM 2.0Supports 4 RS-232,1 RS-232/422/485Supports 1 GPIO(8 channels)
-
Product
Multiprotocol PCI/104-Express Interface Board
8000PCIe104
-
The EXC-8000PCIe104 is a multiprotocol PCI/104-Express interface board for embedded applications or avionics test and simulation applications. Each board holds up to four independent modules and 10 discrete channels.
-
Product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
Controller
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
Product
IEEE 802.11 Ac + BT 5.0 (PCIe - UART)
AIW-154
-
IEEE 802.11ac + BT 5.02 TX / 2RXWide operating temperature -30 ~ 85 °C (- 22 ~ 185 °F)Supports Linux OSM.2 2230 form factor module (L x W x H) 30 x 22 x 2.85 mm/ 1.18 x .86 x .11 inWi-Fi: PCIe / BT: UART
-
Product
Multi-Interface Frame Grabber
Xtium2 CLHS PX8
-
Building on the field proven Teledyne DALSA’s Xtium family of frame grabbers, the Xtium™ 2 CLHS PX8 features CameraLink HS standard on the PCI Express™ Gen 3.0 platform. The Xtium2-CLHS supports Active Optical Cable (AOC) and industry standard CX4 cables. This single cable, single slot solution supports up to 7-CLHS lanes, each operating at 10.3 Gbits/s, to acquire images at up to 8.4 GBytes/s and transfer them using PCIe x8 slots to the host memory.
-
Product
USB-C Thunderbolt™ 3 Appliance with Two Independent, Dual Redundant 1553 Busses, Eight ARINC-429/717 Channels, 4 RX/TX & 4 RX
TBOLT-MA4
USB Interface
Full Featured and Native 1553 and ARINC Thunderbolt interface! Full PCI Express interface – same advanced interface as PCIe backplane cards in a small, portable, rugged appliance.
-
Product
Riser Cards
-
Advantech Riser Cards provide scalability and flexibility for PCI Express(PCIe) expansion slots and 1U/2U systems with Advantech industrial motherboards.
-
Product
PXI FlexRIO Coprocessor Module
Module
PXI FlexRIO Coprocessor Modules feature high-performance FPGAs that add signal processing capability to PXI systems. These modules leverage the latest FPGAs from Xilinx, streaming technologies such as PCI Express, and NI Peer to Peer Streaming for high-bandwidth data communication with other modules over the backplane. When paired with another PXI device, such as a PXI Vector Signal Transceiver, PXI FlexRIO Coprocessor Modules provide the additional FPGA resources required to run complex algorithms in real-time.
-
Product
3U / 6U PXIe Chassis
Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
3U Rackmount Appliance for PCI Express® Gen4
R300-G4
-
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
Product
FPGA Card
PC820
-
The PC820 is a high-performance, PCI Express card with advanced DSP capabilities and multiple I/O options. It supports one FMC+ VITA 57.4-compliant HPC FPGA Mezzanine Card (FMC) that is closely coupled to the Virtex or Kintex UltraScale FPGA and a DDR4-2133 SDRAM SO-DIMM. The PC820s PCIe Gen3 interface can support up to eight lanes.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Channel Serial Lab versions
-
5.0 GT/s 24-lane, 6-port PCIe Gen2 SwitchAll peripheral slots and CPU slot has PCIe interface Gen2 with x4 width10, 100 MHz clock at each peripheral slot1 PPS clock at each peripheral slotGPS module, navigate down to -162 dBm and -148 dBm coldstartMEMS Digital Motion Sensor with ±6g/±12g/±24g dynamically selectable fullscale, 6D orientation detectionHumidity and Temperature Sensor
-
Product
GPU Expansion I-Module
MIC-78MG30
-
1 x PCIe x16 Gen51 x PCIe x2 Gen31 x PCIe x4 Gen3Supports 250W GPU cards
-
Product
Flexible MiniPCI Express to 2 MiniPCI Splitter
SKU-069-2X
-
Flexible MiniPCI Express to 2 MiniPCI Splitter (Splitter) was designed to expand a modern motherboard (ATX, mini ATX etc.) that doesn’t have the MiniPCI interface. It allows you to connect up to two (2) 124-pin MiniPCI add-in boards to a motherboard’s standard MiniPCI Express connector.Splitter includes 2 MiniPCI Adapter boards, MiniPCI Express Host board and 2 Flat PCI Express Cables.
-
Product
3U CompactPCI® 2/4-Port Gigabit Ethernet Card
cPCI-3E10/3E12
Ethernet Interface
The cPCI-3E10 Series is 3U CompactPCI Gigabit Ethernet peripheral card equipped with Intel® 82574L PCIe Gigabit Ethernet controllers. The cPCI-3E10 provides four GbE ports on the front panel (RJ-45) with two switchable to the rear transition module, the cPCI-3E12 provides two GbE ports on the front panel (RJ-45), and the cPCI-3E10-SUB provides two Fast Ethernet ports on the front panel (DB-9). An optional Rear Transition Module (cPCI-R3E10) is available to provide rear access to the GbE ports switched from the cPCI-3E10 front panel.
-
Product
Power Supplies
ZU - SERIES
-
Coolmax ZU series offer 80 PLUS Bronze levels of energy efficiency, massive 12V single rail output gave you the power you needs and modular cable management create a proper airflow inside the case. 6+2 PCI-E connector is suitable for most demanding SLI or CrossFire systems.
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 6U VPX
Model 57141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Switch Device for PCI Express
-
The Switch Device for PCI Express provides two PCI Express upstream ports and eight downstream ports. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel, multiple input, multiple output (MIMO) systems. You can also connect multiple Switch Devices for PCIe to a single PXI Express chassis to create large MIMO systems with a Software Defined Radio Reconfigurable Device.
-
Product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 3U VPX
Model 52841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Bustec VISA Library And Tools
ProDAQ 8200
-
The Virtual Instrument Software Architecture (VISA) is a standard for configuring, programming, and debugging data acquisition and test systems using hardware interfaces like Ethernet, USB, PCI Express, GPIB, IEEE1394 or even RS232. The VISA library provides a standardized application programming interface between the hardware and application programming environments like LabVIEW, LabWindows, Visual Basic etc.
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Reflective Memory PCIE card
PCIE-5565PIORC
-
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
Product
Embedded MXM GPU Module With NVIDIA RTX™ ADA 3500
EGX-MXM-AD3500
Graphics Card
- NVIDIA Ada Lovelace Architecture- Standard MXM 3.1 Type B (82x105 mm)- PCIe Gen 4 x16 Interface- 5120 CUDA® Cores, 40 RT Cores, and 160 Tensor Cores- 23 TFLOPS peak FP32 performance
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5940-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
