Receptacle Testers
test access viability to electricity, gas or data.
-
Product
120 GBd High-performance BERT
M8050A
-
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
-
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
64 Gbaud High-performance BERT
M8040A
-
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Universal Test Socket Receptacle
Series 6556
-
Universal Test Socket Receptacle. The Aries Universal Test Socket Receptacle is sturdy, open frame, and easily mounted to PC boards. Allows for easy replacement of Aries and other manufacturers test sockets. A choice of four collet pin styles makes the receptacle useful for any interconnection method.
-
Product
DER-075 Double-Ended Receptacle
DER-075
-
Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 130Recommended Travel (mm): 3.30Overall Length (mil): 1,710Overall Length (mm): 43.43Rec. Mounting Hole Size (mil): 53Rec. Mounting Hole Size (mm): 1.35Rec. Mounting Hole Remark: 53 to 55 mil / 1.35 to 1.40 mmRecommended Drill Size: #54 or 1.40 mm
-
Product
Universal A/V Tester
-
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
-
Product
DER-050 Double-Ended Receptacle
DER-050
-
Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 130Recommended Travel (mm): 3.30Overall Length (mil): 1,710Overall Length (mm): 43.43Rec. Mounting Hole Size (mil): 40Rec. Mounting Hole Size (mm): 1.02Recommended Drill Size: #60 40mil
-
Product
Rub Tester and Abrasion Tester
RT4
-
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
Product
Hipot Tester
HVA Series
-
HVA systems detect faults in cable networks in a non-destructive yet efficient way and fulfill all the requirements of modern cable testing.
-
Product
ContactLAB Tester
-
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
Product
Flexure Tester
G201A32-33
-
To determine whether metallic wires or materials used for stiffening or retention of form in child-related products can be easily bent or broken.
-
Product
Relay Tester
PTE-50-CE
-
The reversible 100-VA amplifier can inject up to 50A or 150V with outstanding stability, free of distortions and completely isolated from the power supply. The waveform is synthetized electronically and can generate harmonics from 1st to 7th of the supply’s frequency. Various output ranges are available to maintain the 100VA power throughout the entire settings scale. The system features automatic protections against overload and overheating.
-
Product
IC Tester
-
The Peritec adopted the NI products, to build in 1/10 the cost of the commercial product functions of the IC tester. It offers original brand as "ECOIC".IC tester on the market, yet very expensive that several tens of million, part of its function could only really used. Therefore, it possible to continue to build the only really necessary function in Peritec, we have created a mechanism to be completed at a lower cost and development, high-performance, short-term.
-
-
Product
Impact Tester
-
The impact tester is used for testing the impact resistance of materials, to determine their quality under dynamic load conditions.
-
Product
Industrial Tester
-
Ensures products, materials, or systems meet quality, safety, and performance standards by performing tests like voltage checks, mechanical stress tests, or functional simulations, using specialized equipment or manual methods to identify defects and ensure reliability in manufacturing, construction, and technology sectors, often for electrical, data, or material integrity.
-
Product
Qualification Tester
LQ404
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
Product
Installation Testers
-
A Multi-Function installation tester is better then the single function meter. Good quality insulation, a properly working grounding system and active protection assure the safety of people, electrical systems and buildings, and protect them against electrocution, fire and other equipment damage and all of this can be checked by an HT Instruments Installation tester
-
Product
ELT Testers
BT200 Series
-
Building on the features of the industry standard BT100, the BT200 offers improved measurement capabilities and in a fully integrated and ruggedized device. The BT200 meets and exceeds the measurement requirements for EPIRBs (IMO MSC/Circ.1039 and 1040) and for ELTs in the USA (FAA Part 91.207), in Canada (CAR 571 Appendix G), and Europe (CAA/EuroCAE requirements). These Beacon Testers in fact form a cost effective solution by eliminating the need for other costly test equipment. Don’t risk incomplete testing of your beacons – use the BT200 to test them thoroughly. In compliance with your Quality Assurance requirements, detailed calibration data is included with each Certificate of Calibration.
-
-
Product
Multifunctional Testers
-
Electrical installation safety is nowadays more important than ever with the proliferation of increasingly complex domestic electronic appliances people install in their homes that require reliable power supply lest they become damaged and pose a fire and electrocution risk. Effects of unreliable and even dangerous electrical installations are even more acutely felt in industrial environments where they translate into production losses.
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
Continuiy Tester
TE6-0713
-
Hangzhou Tonny Electric & Tools Co., Ltd.
Designed to test circuits while power is on, Use on 6V,12V and 24V applications
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
Product
Adhesion Testers
-
From the largest man-made structures to the smallest household appliances, most manufactured products have a protective or cosmetic coating. Premature failure of this coating can, at the very least, result in additional costs of rework. Adhesion testing after the coating process will quantify the strength of the bond between substrate and coating, or between different coating layers or the cohesive strength of some substrates. Routine adhesion tests are used as part of inspection and maintenance procedures to help detect potential coating failures.
-
Product
Hipot Testers
95X Series
-
Vitrek built the 95X Series from the ground up with DSP technology – to bring you the safest, fastest, most capable, feature rich hipot testers available. The 95X Series combines high output power, with a wide range of AC & DC voltage outputs and extremely low leakage current measurement. Then we added a 4-wire milli-ohmmeter with dynamic range up to 100K ohms and an overlapping Tera-ohm class Insulation Resistance function. Top that off with an available 40 Amp Ground Bond capability and you’re just beginning to get a feel for what the Vitrek 95X Series Hipot Testers can do for you.
-
Product
Component Testers
-
After a wafer is tested through front-end test and back-end test, the component tester tests this final component or package assuring its quality for the semiconductor makers. DDR, DDR2, DDR3 memory component testers.
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
Testers FERVE
-
Thinking of all types of users, FERVE has a complete series of products that provide quick, precise information and ensure perfect testing of batteries and other electrical devices. With fully illustrated instructions manuals, designed by FERVE, SA
