SCR
Thyristor, Silicon Controlled Rectifier
-
Product
Safety Test Panel for Water Cooler
-
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
Product
28 Days Test Bench (Single Phase & Three Phase)
-
The SCR Elektroniks 3 station MCB 28 Days and Temperature Rise Test Bench is economically designed to verify the 28 Days Test (21 hr ON, 3 hr OFF Test) as per clause 9.9 of IEC 60898-1 and Temperature Rise of the parts of a Circuit Breaker specified in Table 6 of clause 8.4.1 measured under the conditions specified in clause 9.8.2 of IEC 60898-1.
-
Product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
-
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
Product
Safety Test Panel for Luminaire Fixture
-
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
Earth Contact Resistance Tester
-
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
Product
Abrasion Test Setup for Coating of Hair Straightener
-
SCR ELEKTRONIKS have developed "4 Stations Abrasion Test Setup for Coating of Hair Straightener" for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
Product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
-
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
Product
Impact Test Apparatus
-
SCR Elektroniks make Impact Test Apparatus is used to test the Electrical Accessories / appliances for their mechanical strength.
-
Product
Advanced SCR Power Controller
Thyro-PX Series
-
50 years of experience are infused in the Thyro-PX® series’ design and functionality. The SCR power controller is available in single-, dual-, and three-phase units, supports voltages from 690 V and 2900 A, and offers superior interface options. Integrate operating modes and parameters seamlessly with the 2.8-inch, LED Thyro-Touch display. And enable efficient system parameters, loading, and storage via an on-board SD-card. Thyro-PX power controller is ideally suited for your transformer and resistive loads for glass, metal, and ceramic manufacturing. It is optimal for heating elements in electric furnaces.
-
Product
Temperature Rise Test Panel
2000A
-
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
Product
Primary Current Injection Test Trolley
-
SCR ELEKTRONIKS have developed primary and secondary Current injection test trolley for Switchgear manufacturers for testing of ACB , MCB , MCCB. It is low Voltage high Current source with control circuitry, digital read out for test current and trip time measurement. We can select different links of CT range as per the required test Current.
-
Product
Fluid Property Sensors
-
TE Connectivity (TE) offers distinct fluid property sensor technologies to measure fluids. Our tuning fork technology is coupled with efficient software algorithms for accurate measurement of viscosity, density, and dielectric constant. Dedicated applications for our DEF sensors include oils quality sensors (engine, hydraulic, transmission), fluid monitoring, and others. Our urea quality SCR sensors, based on Ultrasonic Technology (UST), perform an analysis of the Diesel Exhaust Fluid (DEF) fluid to provide urea concentration and secure mis-filling protection to the Selective Catalytic Reduction systems. Our highly reliable reed switch technology is combined with temperature measurement for DEF level sensing.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
AdBlue & Urea Refractometer
RHA-503ABATC
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
The AdBlue refractometer RHA-503ABATC is a new hand held refractometer developed to address the growing need to check the urea concentration in AdBlue.Escalating urea prices have driven the cost of operating an SCR higher than ever before. Regretfully this has led to a new wave of problems where supplies of diluted AdBlue have found their way in to the market.Often rebranded ‘Automotive urea solution’ to eliminate the risk of prosecution by trading standards (as a mix of less than 31.8% urea cannot be labelled AdBlue). Victims of this weaker concentration may not be able to seek compensation under the Trades Description Act.
-
Product
Shock Test Apparatus
-
SCR Elektroniks make Shock test Apparatus is used to test the Electrical accessories / appliances for their mechanical strength. A wooden base fixed to a concrete block and a wooden platform is hinged base. This platform carries a wooden board, which can be fixed at various distance from the hinge and two vertical positions. The end of board bears a metal stop plate, which rests on coiled spring having constant 25N/mm.
-
Product
Test Setup For Air Conditioner
-
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
Product
Run Down Adapters
Screw RDA
-
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
Product
Secondary Current Injection Test Trolley
-
SCR ELEKTRONIKS have developed SECONDARY CURRENT INJECTION TEST TROLLEY for Switchgear items, CT manufacturer and where three phase current application is called for. It is low Voltage, 3 phase Current source with control circuitry, digital read out for test current and trip time measurement. We can select different CT ranges for each phase independently and adjust the current as per the required test Current.
-
Product
Calibration & Demag.
Model 8515-D
-
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
Product
Software
Scream!
-
Scream! is a Windows and Linux application for Seismometer Configuration, REal‑time Acquisition and Monitoring.
-
Product
Bus Analyzer
Scribe I2C
-
The Blackhawk Scribe is an entry level, yet feature-packed and robust I2C debugging tool. The Scribe was designed to help engineers developing products which utilize the IC and SMBus interfaces.
-
Product
Bench Digital Multimeter, 4.5, USB, 20 A, 750 V, 0.2 Gohm
72-13625
-
This 72-13625 is a manual range, benchtop digital Multimeter that features 19999 display counts, large LCD screen with backlight, full scale overload protection and a unique design. This instrument can be used to measure AC and DC voltage, AC and DC current, resistance, frequency, capacitance, transistor, hFE, diode (LED), SCR, continuity, etc.
