Relay Drivers
Control the energized state of relays.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
Pin Electronics (PE)/ Pin Drivers ATE
-
Analog Devices integrated pin electronics (PE) support speeds up to 2.5Gbps at high accuracy and low power, all manufactured on ADI's proprietary fab processes, providing unmatched test solutions needed for cost-sensitive, test applications.
-
Product
Loop-Powered Transmitters and Drivers
4-20mA
-
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
Product
Protective Relay Testing Equipment
PW466i
-
PW466i (6×20A, 6×150V) 6-phase relay tester is a powerful secondary injection protective relay testing kit with 6-currents and 6-voltages sources.
-
Product
Relay Test Set Type SP-I
-
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
Product
Automatic Relay Test Set
DRTS 34
-
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
Product
Auxiliary Voltage Relays
AVR
-
Type AVR volta acquisition systemscontrol/datage acuated relays are designed for indication alarm of annunciation in elextric utility application. the relays are used for data inputs to supervisory and sequential event recorders
-
Product
Attenuator / Switch Driver
11713D
-
The 11713D attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
Three-Phase Relay Test Set
CMC 353
-
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
Product
Powertest Relay Test Software
-
For all the three phase or six phase relay testers of PONOVO, one universal software can be used, the name is PowerTest software.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
-
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
PCI 32xSPST Reed Relay Card
50-115A-021
-
This is the 32xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
3-Phase Protection Relay Tester
HME-702
-
HAOMAI Electric Power Automation Co., LTD.
Economical 3-phase Protection Relay Testerwith 3-phase current(3×40A) + 4-phase voltage(4×120V) output.
-
Product
SIMRC - 16 x Uncommitted Reed Relay, SPDT
1010-R-16-1-5/3D
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Trip Indicator Relays
TIR
-
The TIR relays are designed for event recording circuit applications, where high speed event monitoring is required. The TIR relay contacts are used to record breaker functions, relay, communication and control system operations. The TIR contacts are also used to activate alarm and/or annunciator contacts.
-
Product
Power Calibrator And Protection Relay Test Set
CP11B
-
Calmet Smart Calibration Devices
Single phase, class 0.02 and 0.05 power quality calibrator up to 120A and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
Measuring & Monitoring Relays
-
Fixed or adjustable threshold for low level or high level voltage or current monitoring.
-
Product
8-CH Relay Output EtherCAT Module
EPS-2308
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
PXI 64 x SPDT Electromechanical Relays
40-148-201
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI Power Relay Module, 6xSPDT, 16 A
40-161A-102
-
The 40/42-161A-102 is a PXI/PXIe 6xSPDT power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Timing Relays
-
Is particularly suitable for use in protection & control schemes where precision time delays are required.
-
Product
Protected Voltage Relay
PVR
-
Type PVR voltage-acuated relays are designed for indication alarm or annunciation in electric utility applications. They are used for data inputs to supervisory control/data acquisition and sequntial event recorders.
-
Product
Signalling Relays
N.S1
-
N.S1 signalling and vital relays are a consistent, adaptable range of relays with plug-in connection, small size, modular construction, low power consumption, compliant to French and SNCF standards, conformity to UIC recommendation, Ag / Ag CdO contacts and 24 V standard.
-
Product
Protection Relay Test Set
PW41i
-
PW41i is designed with 3 currents (3*40A) and 4 voltages (4*300V). The local software system with many relay testing modules is designed based on Windows system, which is easy and convenient for operation and upgrade.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector
42-153-004
-
The 40/42-153-004 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector.
-
Product
PXI 6U Power Relay Module
-
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Three-Phase Relay Protection Tester
GDJB-PC
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.GDJB-PC Universal Secondary Injection Relay Test Set is applied to test the relay unit in relay protection system. 2.At the same time GDJB-PC Universal Secondary Injection Relay Test Set could be considered as a universal three phase AC/DC voltage source or current source. 3.It can work alone or connected to computer, inside the relay controller there are new speed digital signal mini PC and real DAC (Digital-to-Analog Converter) template with new high fidelity and high power, the machine has large panel screen and rotating mouse. It is small in volume, high precision.
-
Product
PXI 17 x SPDT RF Switch 500MHz 50 Multiway Connectors
40-754-017
-
A 50 High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
