-
product
PXI Digital Multimeter, 6 digit, High Performance
M9182A
The Keysight M9182A is a 6digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers 40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V. The M9182A offers advanced triggering capabilities, including pre and post triggering.
-
product
Laser Distance Meters
PeakTech Prüf- und Messtechnik GmbH
This professional laser distance measuring device with multi-line LCD display, which has a backlight, was specially designed for high-precision distance measurements.
-
product
General Purpose Dual Flange Reaction Torque Sensor
TRS SERIES
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
product
Torque Meter Bench
BTR is a desktop torque for torque meas urements consisting of a digital indicator model DTR and a strain gauge torque extremely rugged and compact which has a precision better than 0.20%. Ideal for the calibration and the control of torque keys and to rque screwdrivers. Microprocessor indicator is fed by 4 internal batteries with an autonomy of 200 hours, with the AUTO POWER OFF function which activates if any change in the measurement is detected in an interv al of 30 minutes. The new generation electronic section consists of a particularly long-term stable analogue circuit and of a 16 bits A/D converter which ensures 65.000 internal divisions with an acquisition sp eed of 200 conversions per second. On the display there is an analogue bar for torque, that is still active, even in the programming menu.
-
product
Slide Anvil Type Outside Micrometer
The slidable anvil provides a wide measuring range with a single micrometer.
-
product
Panel-mount Type pH Meter (Four-Wire Transmission, Pulse Proportional Control)
HP-480PL
HP-480PL industrial pH meter is a pH meter with a pulse proportional control function, which can drive a pulse pump directly.It connects pH sensor and measures pH and temperature in the sample water.As the HP-480PL has a high injection resolution per pulse, it can be used to control a pulse pump as part of a system for processing involving fine control of pH values, for example controlling the pH values of microscopic or small samples.
-
product
Manual Tuners
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
product
Explosion Proof Paramagnetic Oxygen Analyzer
Model 3020M
Teledyne Analytical Instruments
The Model 3020P is a versatile microprocessor-based instrument specifically designed to detect oxygen in a variety of gases. It is a precise, cost effective instrument capable of measuring percent oxygen in as low as the 0-1% range. Drawing on the solid performance of the 3000 series control platform, the 3020M provides the user with a wide variety of features and options to satisfy virtually any application.
-
product
Omnidirectional Hotwire Probe
AP3203F
Omnidirectional hotwire probe for cold environment. Measuring range: air speed 0.02 ÷ 5 m/s, temperature -30 ÷ +30 °C.
-
product
Torque Tool Testers
Series TT02
Series TT02 Torque Tool Testers present a simple and accurate solution for testing manual, electric, and pneumatic torque screwdrivers, wrenches, and other tools. These testers are compact and rugged, suitable for production environments. A universal 3/8” square receptacle accepts common bits and attachments. The TT02 captures peak torque in both measurement directions, and also calculates 1st and 2nd peaks, useful for click-type tools.
-
product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Water flow beads)
HR-200
HR-200 is connected to a residual chlorine sensor (RA-20), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents. Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
product
Steel Structure Analyzer
NOVOTEST KRC-M2 (Coercive Force Meter)
Steel Structure Analyzer NOVOTEST KRC-M2 is designed for measuring coercive force of metal products in accordance with IEC 60404-7 and is used for non-destructive testing of chemical-thermal, thermal and thermomechanical treatments, evaluation of mechanical properties and residual stresses.
-
product
RF One Power Meter
The RF One Power Meter is a very versatile instrument covering both analog and digital carriers in an extremely wide frequency range from 30MHz to 6GHz. The RF One is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The RF One instrument is small, handy and light weight battery operated with more than 3 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.
-
-
product
Environments Instruments
This multifunction anemometer provides instant data such as Air Speed and Temperature in Dual Level LCD display with Backlight. This tool has wide measuring range of wind speed from 0 ~ 45m/s (0 ~ 8800ft/min) and temperature from 0 ~ 45°C (32 ~ 113°F).
-
product
Light Intensity Meter
MT-4617
Measures the visible light produced by fluorescent lamp, metal-halide lamp, high voltage sodium lamp or electric incandescent lampBuilt-in precision photo diode sensor and color correction filterAutomatic and manual measured range switchingRelative and peak value measurementMeasures up to 200,000 lux / 20,000 FCExtra functions: Max./Min. value displayOver load indication/Low battery indicationAuto power offBacklightData hold, Zero calibration
-
product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
779785-02
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
product
PXI Switch - 24-CH 2-Wire Multiplexer Module
PXI-7921
ADLINK PXI-7921 is a relay multiplexer which consists of 24 2-wire relays (DPDT, 2 Form C). As a multiplexer, the PXI-7921 provides 48x1 1-wire, 24x1 2-wire and 12x1 4-wire configurations. Users could choose one of the configurations by software. PXI-7921 typically connects one instrument, such as a DMM, a digitizer or a signal source, with many points which need measurement or excitation. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7921, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
Gas Analyser
LT GasAnalyzer
Highly performant analyzer for measuring the concentration of technical gases based on a thermal conductivity sensor, an infrared sensor a para magnetic sensor or combinations of these sensors. Sensors are precise, robust and have a low cross-sensitivity. Extractive online measurement of the concentration of flammable or non-flammable gas components in gas mixtures. Can measure trace oxygen (O2) levels in the parts per million (ppm) range.
-
product
Extractometer
Dynatest
*Extractometer used to measure and check the strength of fixing parts*Test carried out with a four-arm wheel or (and) the hydraulic pump with crank*Results on a pointer/digital indicator with peak value*Lightweight and easy to handle*Simple and quick setting up*Appropriate for on site testing*Packaged in a transport case (with a set of optional accessories)*Revolution counter for the crank*Delivered with a calibration results and the copy of the calibration report for the reference standard sensor
-
product
Distance Sensor Technology
Inductive sensors
Inductive sensors measure the position changes of metal objects without contacting them. The ever increasingly optimized repeatability paired with the outstanding precision in measuring paths, angles, and positions when applied increase the productivity of every machine.
-
product
Power Quality Analyser
PM3000HF
It measures almost every aspect of the electricity you’re supplying or receiving, so is a must for utility, electricity and power supply companies as well as large industrial consumers, from heavy machinery plants to hospitals and supermarkets.
-
product
Vacuum Inspection
INDEC
INDEC vacuum test systems monitor a wide range of containers during the production process, including bottles, jars and cans, by measuring the cap panel concavity of their closures which is dependent on the vacuum inside. This non-contact inspection reliably identifies defective containers for automatic rejection.
-
product
Radiation Meters
A radiation meters is a device designed for measuring varying types of radiation. These devices are portable and are used to inspect personnel, equipment, and facilities for radioactive contamination by measuring the emission of certain radiation particles. They are used to measure external or ambient ionizing radiation field to assess the direct exposure hazard.
-
product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSOV254A
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
1-phase Power Analyzers
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
product
Single Point Aluminium Load Cell
EST-2
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
product
1000 Amp AC/DC Inductive Amp Clamp
6043
• A great tool for accurate measurement of current sources up to 1000 amps• Use with most digital multi-meters• 1mV/Amp output guarantees easy reading on your meter• Ideal for checking starter draw, alternator output or parasitic battery drain testing• Design allows accurate current readings without breaking the circuit• Low battery indication – auto power-off• Switch settings OFF/200A/1000A• Large jaw opening, 2.2″ and large jaw space, 2.2″ x 2.75″• Imported
-
product
Transducers
Rotary Transducers are designed to accurately measure dynamic torque of power tools. Patented design eliminates "brush bounce". The slip ring and brush have a lifetime warranty.
