Link
See Also: Camera Link
-
Product
Microwave Link Interception System
-
Microwave links carry enormous amount of data in the form of voice, data and documents. Interception and analysis of the same can provide Intelligence agencies with whole lot of inputs of Intelligence value. Stratign’s solution enables interception and analysis of the same.
-
Product
Linking Conveyor 765mm
AM307
-
The high performance linking conveyor from 6TL is an option for the users of 6TL36 handling technology. The 6TL36 needs a high performance conveyor in the inlet, that is able to synchronize with the conveyor inside the handling system, so that the UUT can be stopped without phisical stopper, to further proceed with the contacting operation.
-
Product
Framegrabber
FastX1703
-
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
Product
E1/Datacom Transmission Analyzer
DTA-BERT
-
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
Product
Temperature Controlled Microscope Stage
-
Linkham Scientific Instruments
Specialists in temperature controlled microscopy, Linkam Scientific Instruments, announce the launch of their Optical DSC450 which enables simultaneous visualization of thermal processes for improved materials characterisation. The Optical DSC450 enables the user to measure glass transitions and melting behaviour of a wide range of substances whilst accurately controlling temperature from -196 °C to 450 °C. The atmosphere of the stage can also be purged with gas as required by the user. A new feature which will increase the characterisation capabilities of the DSC system is to combine it with imaging capability. The new LINK Digital Imaging module enables additional information to be obtained by correlating optical changes such as colour with temperature. The new TASC analysis tool takes this further. TASC (Thermal Analysis by Surface Characterisation) is a new image analysis capability which enables structural changes in samples to be tracked and quantified optically. It has the unique ability to measure local transition temperatures allowing different points on a sample to be identified. The new DSC system is great tool to use in research and quality control to measure quantitative values for glass transitions, melting peaks and sample purity and, when combined with TASC, even sample homogeneity.
-
Product
Development System
FE-51CC01
-
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Signal Integrity TDR and VNA Software
80SICON IConnect
-
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
Product
Large Rennie Grapnel
-
The Rennie Grapnel is usually used in conjuntion with the Gifford. The Rennie Grapnel is built up of flat links, the fluke passes through the body and is then welded onto it. The links are joined together in sets of four in the form of a chain, successive links and flukes being at right angles to each other. Flukes can be detached for renewal when required.
-
Product
500-Pin SEARAY Connector, Male with Backshell, 1 Amp, 500 Port
C500RMR-4SB-0A
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
EPON OLT ( Optical Line Termination )
OLT-1408
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
Waveguide Detectors 26.5 to 110 GHz
-
Our waveguide detectors cover a broad frequency range of 26.5 GHz to 110 GHz and are available with waveguide sizes ranging from WR-28 to WR-10. The video output ports utilize SMA female connectors. These high performance zero-biased waveguide detectors exhibit excellent performance in Ka, Q, U, V, E and W frequency bands. These types of waveguide detectors are commonly used in various aerospace, defense and commercial wireless applications used in instrumentation, power detection, power monitoring, direct detection receivers, high frequency communications, radar, SATCOM, point-to-point radio, telecom, data links and R&D. The detector circuits use high performance GaAs Schottky Barrier Beam lead diodes with extremely low junction capacitance. These waveguide detector designs perform with minimal sensitivity variation resulting in a flat frequency response across the entire waveguide band. All of the waveguide detectors are in-stock and ready to ship.
-
Product
Battery Test Systems
-
The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.
-
Product
Micro-Ohmmeters
RMO-A Series
-
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
-
Product
PXI MUX 2 Banks of 32 Channel 2 Pole
40-610-022-2/32/2
-
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Bi-directional Amplifiers (BDAs)
-
Triad’s legacy and expertise in amplifying long range, high data rate radio links has yielded many small and lightweight COTS BDAs that are simple to integrate, reliable, and rugged enough to pass any MIL-STD-810G test thrown at them. Our BDAs are the first choice for many radio system designs in applications where more RF power is required to create ultra-long range unmanned data links and other radio communications, and/or in applications that require the highest data throughput.
-
Product
High-Speed Digitizers
ADP7000 Series
-
Guzik AXIe ADP7000 Series High-Performance Digitizer and Digital Processor combine high-speed waveform digitizer with built-in digital signal processing, which both enable mixed-domain signal capture and analysis with high-speed data transfer links to computers. The ADP7000 Modules (ADP7084 and ADP7104) come in a display-less 2U high 19” AXIe modular form factor.
-
Product
Test Kits
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifier (includes MASTER and REMOTE devices) Tests two fibers at a time, cutting testing time in half (when compared to traditional fiber certification) Ideal for installers and contractors who need to certify fiber cables BI-DIRECTIONALLY Measure the end-to-end length of the fiber cable with every test Unlimited sets of job parametersOWLView software allows tri-report capability certification, OTDR, and endface all on one report) Multimode and singlemode options available.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787453-01
-
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Package Testing
-
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
Product
Ultrasonic Testing Systems
-
Matec Instrument Companies, Inc.
Matec designs and constructs a wide range of ultrasonic testing systems, from small laboratory systems designed for simple scanning applications to complex multi-axis systems capable of scanning large parts and complex contour geometries. Click on the links below to learn more about our systems.
-
Product
PXIe-8301, Thunderbolt™ 3 PXI Remote Control Module
785679-01
-
Thunderbolt™ 3 PXI Remote Control Module—The PXIe-8301 enables laptop control of a PXI Express chassis over a Thunderbolt™ 3 connection. Using a Gen 3 x4 PCI Express link, the PXIe-8301 allows up to 2.3 GB/s of sustained data throughput between the chassis and laptop over a Thunderbolt 3 USB Type-C cable. An additional Thunderbolt 3 port allows for connecting additional Thunderbolt or USB-C devices. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
- RS-422 Opto Isolation Module
Model 8381
-
FEATURES: Opto Isolation; Built-in Power Supply; 115.2 KBPS Data Rate; DIN Rail Mounted; Full Duplex; Programmable Terminations. The Model 8381 RS-422 Opto Isolator allows re-generating and extending the distance of RS-422 networks while maintaining optical isolation between the ports. Model 8381 allows for the extension of RS-422 links to a maximum limit of 3,300 feet or 1 km at any data rate up to 115 KBPS.
-
Product
PXIe High Performance System Module with Connectivity Expansion: Dual Port (x16), Gen 3
M9024A
-
The M9024A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The M9024A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
Product
Evaluation and Data Mining
Magpie
-
LXinstruments Magpie is a user-friendly evaluation and data mining application for our test database. The data to be evaluated can be preselected via complex, easily configurable filters. Based on the selected data, it is then possible to create reports and perform statistical evaluations as well as machine capability analyses. The graphical GUI supports easy administration of the database by authorized users.The LXinstruments Magpie evaluation licenses are always linked to the data source, which would generally mean a test system. The test data generated by the test system will be marked as available for evaluation while it is stored in the database.
-
Product
Data Links and Telemetry
-
CAES provides data links and telemetry modules for use in UAV systems, missiles and munitions.
-
Product
Mini Lan Tester
21-8580N-0
-
Auto decipher the link status is NIC or Hub.?The deveices is working in 100 Base -TX Full Duplex 10 Base-T Full Duplex or Half Duplex?The deveiceis transmitting a pack or not?Data transmitting error has occurred
-
Product
Test-Stand Software for TD6 Controller for QMax ATE
TD6 TestStand Software
-
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com
-
Product
Amplifier Systems Band Specific
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Battlefield Operations Support System
TCG BOSS
-
Curtiss-Wright Defense Solutions
TCG BOSS is the industry’s most complete, reliable, easy-to-use, and cost-effective TDL testing and platform integration solution on the market that provides support for multiple terminals and interfaces and adheres to industry data link standards.
