Couplers
enable a signal to be used in another circuit.
-
Product
Passive Component Storage Module Series
TrayPXIe
Data Storage
The TrayPXIe is an accessory tray that stores your fragile passive fiber optic components such as splitters, connector adaptor patchcords, WDM couplers, and isolators in one handy module in the PXI chassis.
-
Product
20 DB Directional Couplers From 0.5 To 60 GHz
-
Pulsar Microwave's 20 dB high frequency single directional couplers make up the CS20 series. They are available in narrow or wideband designs from 500 MHz to 60 GHz. They have a typical coupling tolerance of +/- 1 or 1.25 dB and most models handle 50 watts input power. These directional couplers are designed to operate in a 50-ohm system, and are optimized for best matching and high directivity with flat coupling response.Standard outlines are offered in SMA or N type female packages, either all of one type or combination with N type mainline and SMA coupled port.
-
Product
Dual (Bi) Directional Couplers
-
Pasternack dual directional coupler (also known as bi-directional coupler) series are passive devices that couple part of the transmission power in a transmission line. Our dual directional coupler components provide the bandwidth, high directivity and higher power that designers need for their most demanding applications. RF dual directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack bi-directional coupler items are RoHS and REACH compliant. Couplers that are dual directional from Pasternack are available with SC, SMA and Type N connectors. This dual/bi directional series is offered in 10dB, 20dB, 30dB, 40dB and 50dB coupling values. Power ratings for our dual directional couplers range from 10 Watts to 10 Watts. Frequency ratings for our bi-directional couplers range from 1 GHz to 8 GHz. Like the other over 40,000 RF, microwave and millimeter wave components from Pasternack, our dual (bi) directional coupler series is in-stock. Not only our these couplers in stock, they also will ship the same-day as they are purchased.
-
Product
High-Speed CMOS Output
-
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
-
Product
LGX Couplers, Splitters, And WDM Modules
-
To support growing and changing network connectivity needs, M2 Optics offers a complete line of LGX fiber optic couplers, splitters, and WDM solutions. Every LGX module is customized to user specifications, providing a wide range of configurations that save cost and rack space.
-
Product
X Band Coupler With Dual Output Threshold Detector
-
The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.
-
Product
Inductive Coupler
CLAMPMITTER™
-
The CLAMPMITTER™ is a unique tool for inductive coupling. This self-contained inductive transmitter increases productivity, promotes safety and simplifies locates by condensing the transmitter and inductive coupler into one cordless package. Whether climbing down a manhole or accessing a utility box, the Clampmitter is an easy alternative to suiting up with a full transmitter and wired coupler.
-
Product
REM-11115, 4-Channel, 2-Wire Analog Output Module for Remote I/O
784749-01
Analog Output Module
4-Channel, 2-Wire Analog Output Module for Remote I/O - The REM‑11115 is an analog output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11115 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. You can use the REM‑11115 for voltage or current output, and it features a 2‑wire spring terminal connection method. The REM‑11115 has selectable output ranges and short-circuit-proof output channels.
-
Product
Fuel Injection Pressure Tester with 2 Gages & Quick Couplers in Storage Case
53980
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
Passive Component Integration - MATRIQ
Passive Component Integration
The Passive is a highly customizable benchtop accessory that can integrate the passive components of your choice for convenient storage and integration into your test set up.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
Product
Diode Power probe
-
The COMM-connect 3026 Diode based temperature compensated probe is designed for use with the COMM-connect range of Power Monitors. The probe will handle from 50µW to 100mW . Used with external couplers and the our measurement system application from 1W to 1MW, a high dynamic range can be configured. The 3026 Diode based probe gives excellent stable results along with the COMM-connect Power Monitor variants. This gives our customers a number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Antenna Coupler, 300 MHz - 6 GHz
dbCOUPLER
-
The dbCOUPLER is ideal for many different applications including security, GNSS, Bluetooth, WiMAX, Wi-Fi, 5G, LTE, and RFID (vUHF SHF).
-
Product
PhotoIC Couplers
-
Panasonic Industrial Devices Sales Company of America
A Commercialized PhotoIC Coupler For High-Speed Communication Between Industrial Equipment. Panasonic, a worldwide leader in cutting-edge electronic components, has developed and introduces the NEW APS1 Series PhotoIC Coupler that transmits light signals while allowing electrical insulation. This revolutionary new product is designed for high-speed transmission of signals between industrial equipment such as motors and PLCs.
-
Product
Pump Combiners
-
Pump combiners, also called pump couplers, are special application fiberoptic couplers used for sending pump and signal light into an amplifier or laser fiber. Because of these applications, pump combiners are specially designed for high-power use.
-
-
Product
Magic Tee
MHTXE
-
The MHTXE Magic Tee Hybrid Couplers for millimeter waves are matched power dividers for variety of applications (general purpose power splitters, power combiners, phase measurement circuits, phase / frequency discriminators). The MHTXE Magic Tee Hybrid Couplers are available in waveguide bands between 33 and 170 GHz. These couplers are four-port transmission line components with a port configuration as shown in figure. Operation bandwidth is limited to 20÷90% waveguide operation frequency range depending on performance specifications.
-
Product
Couplers
BP1090
-
*Measure Speaker/Receiver Characteristics*Measure Speaker/Receiver Sound *QualityTest Earphones for Sound Quality and Balance*Measure Rub & Buzz*Test in QA, QC or on the Product Line
-
Product
Additional Components
-
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
Product
90 Degree Hybrid Couplers To 500 MHz
-
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
Product
Passive Components
-
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
Product
PHOTO COUPLER TESTER
-
May be linked to machine handler for automatic test on production line.Test items include：VF、IR、Vceo、Iceo、Vsat、CTR
-
Product
Directional Couplers & Bridges
-
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
Product
Fiber Coupler Diode Laser
CAWS-XX
-
* High Power，High Efficiency* Coupling efficiency ≥80%* Standard fiber connector type* Lifetime > 10000h
-
Product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
-
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
Product
Integrated Couplers/ Harmonic Mixers
-
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
Product
PM Coupler
-
Zhongke Rayzer Optical Technology Co.,Ltd
Polarization Maintaining Fused Tap Coupler product, is used to divide input polarization maintaining fiber into two outputs according to the established spectral ratio. It is widely used in the fields of fiber laser, fiber amplifier, fiber communication and fiber sensing, with compact configuration, low insertion loss, low polarization related loss and high stability.
-
Product
Ear Simulator
BO1028
-
The BO1028 Ear Simulator is a special coupler for microspeakers or earbuds that has been designed to be compliant with ATU-T P.57 and IEC 60318-1. While mics in our BP1090 couplers receive sound waves the way they travel through air, the dual compartment chamber of the BO1028 is designed to modify sound pressure so that the mic receives air vibrations the way a human ear drum would receive them.
-
Product
PD Coupler
-
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
Product
Signal Conditioning
-
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
Product
Coaxial Directional Coupler, 1 GHz to 20 GHz
87300B
-
The Keysight 87300B is a compact, broadband directional sampling coupler designed for signal monitoring or, when combined with a coaxial detector, signal leveling. It is supplied with SMA female connectors.
