Voltage Sensors
See Also: Voltage Transducers, Current Sensors, Voltage Calibrators
-
Product
PXI High Voltage Power Multiplexer, Dual 12:1
40-331A-002
-
The 40-331A-002 dual 12:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
Thermocouple Power Sensors
N8481B
-
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Resistance Temperature Sensors
-
Watlow Electric Manufacturing Company
These sensors are suited for applications where accuracy and stability are essential for proper control in applications that operate at or below 1200°F (650C).
-
Product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-904
-
The 65-233-904 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Industrial heat flux sensor
HF05
-
Hukseflux Thermal Sensors B.V.
The HF05 heat flux sensor is used to measure heat flux in industrial environments. It is covered with a stainless steel cover.
-
Product
High Voltage Probes
-
High voltage measurements have a variety of different requirements, and our PVM series and VD series probes are designed for most of these requirements. The PVM probes are designed for wide bandwidth and ease of portability where a variety of measurements must be made. The VD series probes are designed for use at higher voltage ranges, and where physical stability is required.
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
Sensors
-
Electronic Product Test & Design
Development kit has ideal support for software development, prototyping and depth-sensing evaluation.
-
Product
Series Dual Temp / Acceleration Sensors
TA104
-
Dual Temperature / Acceleration Output, Side Exit Connector / Cable, 100 mV/g, 10 mV/?C
-
Product
Rotary Motion Logger Sensor
NUL-226
-
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
Product
Single Axis AC Magnetic Field Sensor
MGCH-2
-
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
wavefront sensors
HASO EUV
-
Imagine Optic's HASO EUV wavefront sensor, developed in conjunction with LOA and the SOLEIL synchrotron, is the only device of its kind available that offers you the extreme precision and direct measurement functionality needed for today's demanding laboratory and industrial applications.
-
Product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8 KIT
-
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
Underwater Quantum/PAR Sensors
-
Photosynthetic radiation is essential for the growth of the photosynthetic organisms such as corals. The wavelength range from 400 to 700 nm is PAR (Photosynthetically Active Radiation) or PPFD (Photosynthetic Photon Flux Density). Apogee quantum/PAR sensors are calibrated to measure the number of photons of light across this range.
-
Product
33% Satured Solution for RH Sensor
HD33
-
33%RH saturated solution for checking the relative humidity sensor, complete with screw adaptor for probes ∅ 14mm, M12×1 thread.
-
Product
Voltage Controlled Oscillators
-
Mercury Systems’ VCOs (Voltage Controlled Oscillators) offer predictable consistency, rugged design and reliable performance. Our VCO products will meet your application’s most demanding stability and low phase noise requirements; featuring wide tuning bandwidth up to an octave. With custom designs and space qualified versions, trust Mercury to provide the VCOs for your next design.
-
Product
Temperature Measurement IR Sensors & Detectors
M34
-
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
-
Product
Eddy Current Sensor
eddyNCDT 3001
-
The eddyNCDT 3001 is a new, efficient eddy current sensor whose compact dimensions have to date only been reserved for inductive sensors and proximity sensors. The temperature-compensated design provides high stability even in fluctuating ambient temperatures. The eddyNCDT 3001 comes with integrated electronics, offering an outstanding price/performance ratio and easy operation. The eddyNCDT 3001 eddy current sensor is ideally suited to OEM integration and machine building applications. The sensor is factory-calibrated for ferromagnetic and non-ferromagnetic materials, which eliminates the need for field calibration of the sensor. The eddyNCDT 3001 is available with connector or with integrated cable. A robust design combined with the eddy current measuring principle enables measurements in harsh industrial environments (oil, pressure, dirt). In addition, the eddyNCDT 3001 is suitable for offshore/marine applications (salt water).
-
Product
Bluetooth Vibration Sensors / Bluetooth Accelerometers
-
A Bluetooth Vibration Sensor is an Accelerometer capable of recording vibration data and transfer it to a receiver using Bluetooth standard protocol. These sensors usually integrate an accelerometer and a bluetooth transmitter to establish wireless connectivity. Hence having the capability to connect via peer to peer or mesh network.
-
Product
Radar Level Sensor
VRS-20
-
Versatile and simple to install, the VRS-20 has been developed by Valeport to work seamlessly with the TideMaster Tide Display/Logger and other third party data loggers using RS232, RS485 and SDI-12 communication. Non-contact technology removes the installation, corrosion & fouling issues of submerged sensors, while simplifying datum control. Accuracy and performance are unaffected by changes in water density and atmospheric conditions.
-
Product
High Pressure Sensors
-
Honeywell Industrial Automation
Honeywell Sensotec is among a handful of companies offering pressure sensors that can measure pressure up to 200,000 psi with superior accuracy and reliability. Foil based strain gauge technology enables our pressure sensors to withstand pressure that would destroy silicon based or micromachined pressure sensors.
-
Product
Low Noise Accelerometer Cables & Coaxial Sensor Cables
-
Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.
-
-
Product
Hand Dynamometer Logger Sensor
NUL-237
-
This sensor comes with a hand held unit with a built in strain gauge. The sensor measures the pressing force on the hand held unit.
-
Product
50 Ω High Voltage Pulse Generators
-
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
Product
EOL Testing of Speed Sensors
-
Complete programming and end of measuring stations integrated in the assembly line for rotary electronic sensors with automatic sensor recognition.
