Current Detectors
-
Product
200 Amp AC Current Adaptor
DL6701
-
The DL6701 is a compact 200A AC current clamp adaptor with voltage output via standard 4 mm connectors. To be connected to a digital multimeter or other voltage measurement device.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-3000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra big CT window*AC 1A～3000A*Current measurements of main cable
-
Product
Direct Current Measurement Card
LQI5
-
Computer Gesteuerte Systeme GmbH
The LQI5 is a precision direct current measurement card. It features 6 measurement ranges for unipolar current measurements of up to 32 A. Current pulses shorter than 5 seconds can be measured up to 65 A.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 Meter Cable
CP150-6M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Current Meter
MTD32
-
The mezzanine module (mezzanine) MTD32 is designed to measure instantaneous current values over 32 channels.
-
Product
Proximity Voltage Detectors
-
Verify the presence of voltage without contacting the conductor. Audible and visual alert when voltage is present. Powered by a rechargeable Li-Ion battery. HI/LO proximity voltage detector with two voltage ranges, 50V-4kV and above 4kV.
-
Product
Ultrasound Detectors
Checker Range
-
Ideal for reliability departments adopting operator driven reliability (ODR), Checkers engage any stakeholder who is responsible for ensuring reliable operation of their assets prior to, during, and after their shift
-
Product
Current Booster
BUX
-
The current boosters allow performing tests up to 2000A, 3000A and 5000A. The option is made of a module, which incorporates a power transformer, which generates a low-voltage, high current output and a metering CT, which measures the output current and sends the metering to eKAM.
-
Product
5 Amp High Accuracy Current Probe
HA5
-
Our HA5 Current Probe covers the measurement range from 20 milliamps to 5 amps, making it the best choice for measuring very small loads and the outputs of CT (Current Transformer) step-down circuits.
-
Product
4/8 Channel 1.0 ~ 30.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808C
-
The UC INSTRUEMNTS CA9808C 4/8 Channel 1.0 ~ 30.0 Gb/s pulse pattern generator and error detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 Gb/s to 30.0 Gb/s each Channel. 4/8 channel 30.0 Gb/s make it total up to over more than 120/240 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
Line Scan Detectors
-
a machine vision device that captures images one row of pixels at a time, rather than a full frame at once.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 12-Channel, 1-Pole
40-514-107
-
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
-
Product
High End Current Sensors
-
AC and DC currents with an accuracy down to 1ppm. Our standard products offers the following features: Automotive current sensors. Extended temperature current sensor - 85 deg Celcius. AC current sensor - DC current sensor.
-
Product
Standard Round 2m Cables, Shielded, for Higher Current
ST010-S
-
Connection to digital boards, intended for higher currents. to be used with CPCI-1500, APCI-1500, APCI-1564, APCI-2032.
-
Product
4 Channel 24.5~ 29.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808
-
The UC INSTRUEMNTS CA9808 4 Channel 24.5 ~ 29.0 Gb/s (100Gb/s) Pulse Pattern Generator and Error Detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 24.5 Gb/s to 29 Gb/s each Channel. 4 channel 29.0 Gb/s make it total up to over more than 100 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
Current To Pressure Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Current to Pressure Trainer. This setup comprises of a I to P converter fitted on a base. Two pressure gauges are fitted one at the input side and the other at the output of the I to P converter. A current source with digital display is provided to excite the I to P converter. A constant air supply should be provided to the system at 20 PsI Pressure from a standard compressor.
-
Product
Current Probe For Multimeters
CP 1000
-
The CP 1000 current probe has been designed for use with multimeteres respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Cryogenic Current Comparator (CCC)
6200A
-
Measurements International Ltd.
Introducing the Model 6200A Cryogenic Current Comparator Bridge (CCC) from Measurements International (MI) – the ultimate solution for achieving the highest level of resistance calibration accuracy. With an uncertainty of less than 3 parts in 10-9, our CCC surpasses all other technology on the market.
-
Product
Smallest Multimetric Nanoparticle Detector
partector 2
-
Naneos Particle Solutions gmbh
The naneos partector 2 is the world's smallest multimetric nanoparticle detector. The partector 2 uses dual non-contact detection stages to measure not only lung-deposited surface area like the partector 2 Light, but also particle number concentration and average particle diameter. Additionally, ultrafine particle (UFP) surface and ultrafine particle mass concentrations are calculated and displayed. In contrast to some of our competitors, the UFP mass is displayed online, and it is calculated using the measured diameter of the particles, rather than estimated by a simple multiplier for LDSA.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-01
-
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
Terahertz Generators and Detectors
-
Terahertz generators and detectors are produced and optically prepared at the facilities of Rainbow Photonics in Switzerland.
-
Product
Fixed Gas Detectors
-
Crowcon offers a flexible range of fixed gas detection products which are able to detect flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment. We use a variety of measurement, protection and communications technologies and our fixed detectors have been proven in many arduous environments, including oil and gas exploration, water treatment, chemicalplants and steel mills.
-
Product
Metal Detectors
-
Zircon’s MetalliScanner® metal locators are designed with both the professional contractor and DIYer in mind. Wether you need to find rebar in concrete, pinpoint smaller metal targets like nails, or locate live AC electricity, Zircon has a tool for your metal detection needs.
-
Product
Eddy Current Testing
-
Shanghai Xianda Denshijiki Industry Co.,Ltd
And the eddy current generated on the specimen by the specimen by the action of the magnetic field can not be detected (defect) and the change due to the influence of the material is detected.
-
Product
Current Sense Magnetics
-
Current sense magnetics are used as a low loss method for sensing AC current in a circuit and also provide electrical and safety isolation between the source of the current and the measurement circuit. The key parameters for a current sense transformer are the rms current rating (to ensure it does not overheat in the application) and the safety and voltage isolation (to ensure it conforms to the end-application requirements).
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Current Sensing
-
voltage-output, current-sensing amplifier family that integrates an internal shunt resistor to enable high-accuracy current measurements at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, low- or high-side current-shunt monitor that allows an external reference to be used to measure current flowing in both directions through the internal current-sensing resistor sensor. The integration of the precision current-sensing resistor provides calibration equivalent measurement accuracy with ultra-low temperature drift performance and ensures an optimized Kelvin layout for the sensing resistor is always obtained.
