Coil
One or more spiral turns of a conductor.
See Also: Helmholtz Coils, Coil Turns, Rogowski, Impulse Winding Testers, Transformer, Inductor
-
Product
AC/DC Clamp Meter
3800 CL
-
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
Product
PXI-2567 , 64-Channel PXI Relay Driver Module
778572-67
Relay Driver
64-Channel PXI Relay Driver Module—The PXI‑2567 is an external relay driver that works with internal or external power sources. The PXI‑2567 allows you to control relays when the current and voltage requirements for those relays exceed the capabilities found in existing relay modules or for relays embedded in a test system. The PXI‑2567 includes overcurrent, overvoltage, and flyback protection to ensure long-life operation. The PXI‑2567 can also drive small DC motors or other inductive relay coils.
-
Product
High Voltage Surge Testers
HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
Portable Single Phase Power Factor Meter
-
Supreme Instrument Laboratories
Portable Electro-dynamometer type single phase single element Power Factor Meter laboratory type for horizontal use, housed in laminated wooden cabinet size 235 mm length x 200 mm width x 180 mm height, with detachable lid, black bakelite panel fitted with anti-parallax mirror scale, knife edge pointer, rubber footings, carrying handles, locking arrangements. The power Factor Meters are fitted with an iron shielded Electro-dynamometer type cross coil system.
-
Product
SIL Reed Relays
Series 105
-
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
Product
Circuit Breaker Analyzers & Timers
-
CAT circuit breaker analyzers and timers are advanced standalone or a PC controlled instruments for circuit breaker maintenance. Typical application areas of CAT instruments are medium and high voltage substations at electric power generation, transmission, and factories of switchgear. Also, industrial environments and electric power distribution are suitable application areas for these circuit breaker testing instruments.DV Power CAT circuit breaker testing instruments are portable and lightweight. They are designed for performing mechanical operations intended for circuit breakers testing according to standards IEC 62271-100 and IEEE C37.09.These instruments measure:the timing of main contacts, pre-insertion resistor contacts, auxiliary contacts operations,coil currents,motion parameters,voltage recording,main circuit resistance,arcing contacts wipe,and any relevant analog signal.Motion transducer channels provide measuring a displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time, and average velocity. Even more, CAT circuit breaker analyzer optionally has a built-in micro-ohmmeter. Hence, it provides the main circuit resistance measurement and dynamic resistance measurement. Dynamic resistance measurement is an effective method for arcing contacts condition assessment.
-
Product
Process EDXRF Spectrometer
NEX LS
-
Applied Rigaku Technologies, Inc
Featuring advanced third generation EDXRF technology, the Rigaku NEX LS represents the next evolution of scanning multi-element process coatings analyzers for web or coil applications. To deliver superior analytical performance and reliability, the EDXRF measuring head assembly was derived from the established Rigaku NEX Series high-resolution benchtop instrumentation. With this proven technology, the Rigaku NEX LS delivers rapid, non-destructive, multi-element analyses — for coat weight, coating thickness and/or composition — for elements from aluminum (Al) through uranium (U). The measuring head is mounted on a rigid beam and is equipped with a linear traversing mechanism positioned over a roller so that the head-to-surface distance is constant. Common applications include silicone release coaters, converters, denesting Si for vacuum-formed plastics, RoHS compliance, conversion coatings, metalized plastic, top coatings on metal coil and fire retardants on fabric.
-
Product
S Series Panel Meter
ST-670
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 30A● Hz Meter : Measuring Ranges : 45~55 Hz, 45~65 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate..● Pointer：Tube or knife-type, color in black or red.
-
Product
Power Supplies
-
AC and DC power supplies are used for providing the power required for energising the trip and close coils of the breaker and for running the spring charging motor. The appropriate AC or DC configuration of the power supplies can be selected, depending on the DUT specifications of the manufacturer. Dual-mode AC/DC power supplies capable of providing AC and DC outputs from the same power supply are also available, if required by the user.
-
Product
Resistance Measuring Device According to DIN EN 61557-4 (VDE 0413-4)
-
PeakTech Prüf- und Messtechnik GmbH
An extremely robust milliohm measuring device in a splash-proof hard case for professional field service use, e.g. for resistance measurement on motor coils, generators and transformers or for continuity testing on ring bus systems in industrial plants.
-
Product
Tire Pyrometers
52-50690
-
Longacre Racing Products, Inc.
Computes tire temp averages for temps just taken, recalled from memory, or you can even manually enter temps taken previously to compute averages. Advanced electronics stabilize your readings quickly giving you accurate, consistent results. Pyrometer comes with a built-in night light with auto shutoff, fast response coiled cord adjustable tire probe, and carrying case. It also features a built-in four car stopwatch with 75 lap memory for all 4 cars.
-
Product
Rogowski Coil
ARU Series
-
*Class accuracy 0.5 conductor centered according to IEC 61869-10*Better than 1% accuracy regardless of the primary conductor’s position*Rated insulation voltage 1kV CATIII
-
Product
Roughness Tester
-
Compatible with four standards of site to measure surface roughness ofvarious machinery-processed parts, calculate corresponding and clearly display allmeasurement parameters. When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
Product
Coil Test System
CTS
-
International Electro-Magnetics, Inc.
The system is controlled by a PC using software written in Visual Basic. It offers visually oriented menus that allow easy coil configuration and test set up procedures.
-
Product
Single-in-Line Reed Relays
Series 117
-
SIL relays - Very High Density Instrumentation & ATE. Smallest board area. 1A version requires 0.15 x 0.27 inches (3.8mm x 6.8mm). 1 or 2 switches with 3 Watts rating. 5 Volt coils with optional diode
-
Product
Turns Counter for Bobbin Coils
TC-5 / TC-5A
-
International Electro-Magnetics, Inc.
The TC-5 is designed to verify the turns count of bobbin or free wound coils. When calibrated with a "Production Standard" coil, the TC-5 can measure to an accuracy of 99.9% or 1 turn in 1,000 for coils of less than 10,000 turns.
-
Product
Coil Analyzers
Sat40a II Series
-
The Coil Analyzer SAT40A II series is a powerful tool for testing circuit breakers where a substation battery is not available. It is unique device in the market due to its dual purpose: - It can be used as a stable power supply for coils and spring-charging motors (both DC and AC power supply voltage) during commissioning and maintenance testing. - It is powerful analysis tool for assessing conditions of circuit breaker auxiliary circuit and coils. The Coil Analyzer SAT40A II series has separate DC and AC coil outputs for power supply of opening and closing coils. The output voltage is selectable in the ranges from 10 V to 300 V DC or from 10 V to 250 V AC. The Coils outputs can withstand up to 15 A current. The DC and AC motor outputs can generate from 10 V to 300 V DC and 250 V AC voltage. The motor outputs can withstand starting (inrush) currents up to 40 A. These outputs can also be used as continuous power supply outputs.
-
Product
PCI Relay Driver Card, 64-Channel
50-411A-001
Relay Driver
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
Product
AC/DC Clamp Meter
3801 CL
-
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● LCD backlight display.● Flashlight function.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
Product
Portable AC/DC Power Supply
UPS S3
-
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
Product
Helmholtz Coils
-
Helmholtz coils is a candidate test apparatus for low frequency magnetic field susceptibility testing on military equipment and subsystems. Use of this coils reduce electromagnetic compatibility (EMC) qualification tests time, and subject the equipment under test (EUT) to a relatively uniform field.
-
Product
Resistance Measuring Equipment
-
measure coil winding resistance of motors, transformers, etc, under energizing AC voltage. The direct reading is possible with 4-wire measurement method, and temperature of specimens is immediately calculated from measured resistance values and displayed. Ambient temperature is automatically taken in by connecting an option sensor Model DAC-PT-100.
-
Product
5MP RAW MIPI Camera Module (Bayer)
e-CAM58_MI5680_MOD
-
The e-CAM58_MI5680_MOD is a 1/3.2" optical format, 5MP RAW MIPI Camera Module based on OmniVision's OV5680 CMOS image sensor and it provides RAW Bayer format image output through its 2-lane MIPI CSI-2 interface. Combined with the 1.75 micron pixel size and the OmniVision's OmniBSI-2 pixel technology, this autofocus camera module provides best-in-class sensitivity and excellent noise performance. The small form-factor camera module also contains the voice coil motor (VCM) based lens mechanism for adjusting the focus position of the built-in lens and the same can be used with an external back-end ISP to implement the autofocus capability.
-
Product
Impulse Voltage Generator
-
Hilo-Test manufactures Surge generators for surge voltage and safety tests as well as for testing the insulation withstand voltage, the waveform in accordance with IEC 60060. Especially for EMC tests on photovoltaic systems and surge voltage tests, for example, to relay, capacitors, coils.
-
Product
Decoders
SwitchPilot
-
Electronic Solutions ULM GmbH & Co. KG
The ESU SwitchPilot Decoder is especially optimised for the stationary use on your layout. Regardless of what you prefer, the usual twin coil magnetic switches, switching electrical light signals or an ultra-modern servo control: One of the SwichtPilot decoders will "fit".
-
Product
Ignition Analyzer
KG-300
-
Ignition coil measurement, failed coil checking and cylinders comparison.
-
Product
Electrodynamic Shaker Systems
-
Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.
-
Product
Circuit Monitor
CM, CMD
-
*Continuous monitoring of trip coil continuity*LED indication of open trip circuits*N.O. or N.C. contact for remote indication of open trip coils.*Self-monitoring — long-life*Can also be used as a self-latching, high speed target for trip indication*UL Recognized*RoHS Compliant (Directive 2002/95/EC)
-
Product
Surface Roughness Meters
-
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
Product
W Series Panel Meter
ST-100R
-
Standard Electric Works Co., Ltd
● Accuracy : Moving Coil Type DC, Class 2.0 Moving Iron Type AC, Class 2.5 Rectifier Type AC, Class 2.0● Case and Composition : Acrylic resin front and bakelite case. Bevel mounting.● Color : Black case and white scale plate.● Pointer Shape：Tube type, color in black or red
