Mezzanines
Is the stacking of cards into a single card that then plugs into the computer bus or data path.
-
Product
Mezzanine System
5033
System
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Interface
EPMC-1553-8
Interface
Abaco Systems EPMC-1553-8 is the first PMC (PCI Mezzanine Card) module to offer 8 dual redundant MIL-STD-1553B Notice II channels. Available in commercial, ruggedized and conductively cooled versions with eight dual-redundant channels, the EPMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Mezzanine Module
RS485-MOD2
-
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
XMC mezzanine module
XMC-620
-
Curtiss-Wright Defense Solutions
The XMC-620 from Curtiss-Wright Defense Solutions is a small form factor XMC mezzanine module optimized to provide all the power and versatility of Cisco IOS running as an Embedded Services Router (ESR). Designed for mobile and airborne systems, the XMC-620 extends the power and versatility of an enterprise router to a rugged embedded platform.
-
Product
Accelerators
-
Our GPGPU embedded processing accelerators are powered by NVIDIA or AMD devices that are picked for their long service life support and suitability for embedded processing applications. Each GPU processor is mounted on a rugged mezzanine for upgradability.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT791
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
XMC-to-PCI Express Adapter
7988
-
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
XMCDisk, SATA Adapter
9292
-
The 9292 XMCDisk is a rugged mezzanine storage solution designed for applications requiring high speed operation with high capacities and zero slot usage.
-
Product
64x LVDS Module
LVDS-MOD4
-
Curtiss-Wright Defense Solutions
The LVDS-MOD4 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright Xilinx Virtex II-Pro and Virtex-5 FPGA-based processing PMC modules, the PMC-FPGA03, PMC-FPGA05, and XMC-FPGA05D. This module provides 64 differential I/O pairs to the front panel. The LVDS-MOD4 LVDS I/O module is aimed at embedded application development.
-
Product
Oscilloscope
MOSTS6
-
*MOSTS6 is the first Russian instrument (oscilloscope) with a direct sampling rate (8bit ADC), 5 Gigasemp / s per channel. M-module MOSTs6 is designed to work as a part of information measuring systems based on the VXI bus magister as a digital oscilloscope. The M-module is made in the form of a triple-width mezzanine, is installed on a mezzanine carrier and is connected to it via a local information highway.*MOSTS6 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent channels.MOSC6, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
Product
IC-RBP-XMCa, Active network redundancy XMC Switch Mezzanine Card
IC-RBP-XMCa
-
IC-RBP-XMCa, Active network redundancy XMC Switch Mezzanine Card.
-
Product
FPGA Mezzanine Card
FMC172
-
The Abaco FMC172 wideband low latency FMC module is based on the latest high performance ADC device from Texas Instruments and DAC devices from Teledyne-E2V. It is the fastest ADC Abaco offers with LVDS interfaces, delivering up to 6.4 GSPS ADC on a single channel (or two channels @ 3.2 GSPS) and a single channel DAC at up to 6.0 GSPS, making it among the fastest low-latency devices available on the market. The combination of the FMC172's >6.0 GHz bandwidth, its high sample rate and low latency is ideal for advanced Digital RF Memory (DRFM) systems.
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
Communications Module
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
40/25GbE Network Mezzanine Cards
-
a specialized high-speed network interface card (NIC) designed to plug directly onto a server's motherboard (or into a dedicated slot) to provide high-bandwidth connectivity—specifically 25 Gigabits per second (GbE) or 40 GbE—without using a standard PCIe expansion slot.
-
Product
3U VPX PMC/XMC Carrier Board
IC-CMC-VPX3b
-
The IC-CMC-VPX3b is a carrier board designed to expand 3U VPX system capabilities with the integration of PMC/XMC mezzanines.
-
Product
Carrier Card
SPR518
-
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
Product
256 Digital Input/Output Channels
CP387
-
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
Product
PMC Carrier Card
APC-PMC
-
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
PXI Express Board
SMT722
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Strain Gauge Module
МТМ8
-
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
-
Product
Quad 1.25 Gsps 14-bit ADC FMC
ADF-Q1214
-
The ADF-Q1214 Quad Channel ADC FMC module from DEG delivers 14 Bit resolution at a sample rate of 1.25 Gsps . As a VITA 57.1 compliant FPGA Mezzanine Card (FMC), the ADF-Q1214 converts four channels of up to 2.0 GHz analog input bandwidth providing direct coupling of unparalleled analog-to-digital conversion capability with PCIe or VPX carrier boards.
-
Product
8-Channel ADC Module
FMC107
-
Sundance Multiprocessor Technology Ltd.
The FMC107 is an eight-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC107 card provides eight 12-bit 65 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC107 has the LPC (Low-Pin Count) 160-Pin connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
Product
8 Ports 10GbE SFP+ Network Mezzanine Card
NMC-1012
-
1 x Intel® E810-CAM2, 8 x SFP+ slots. 1 x PCIe x8, Gen4. CE/ FCC, RoHS compliant.
-
Product
Frequency Converter up UHF AXIe-0 Up
AXIe-0 Up UHF Module
-
The AXIe-0 Up LMHF module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of double mezzanines. The number of slots in the module is one.
-
Product
XMC Mezzanine Processor Card
XMC-528
-
Curtiss-Wright Defense Solutions
The XMC-528 is a high-performance, user-programmable processing and FPGA resource for embedded security applications or use as an FPGA co-processing engine.
-
Product
Interface Module
MC
-
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
Product
16-Port Serial Controller
PMC523
Controller
The PMC523 provides a flexible solution for technology insertion by integrating multiple serial I/O channels onto a single board computer (SBC) with a PCI Mezzanine Card (PMC) site. This gives customers affordable protection from obsolescence and a smart evolutionary path to enhanced software ultimately improves performance and increases efficiency.
