Audio Cable Testers
-
product
Audio Cable Testers
AudioJog Pro 3
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
product
12 Plug Pro Audio Cable Tester
PCT40
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
product
Audio Cable Tester
CBT-500
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
product
8 Plug Pro Audio Cable Tester
PCT10
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
product
Audio Cable Testers
AudioJog Pro 5
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Performance Audio Analyzer
U8903B
Measure your most demanding audio devices with higher accuracy and a low residual distortion of -110 dB See the real performance of your devices with the highest resolution audio measurements available Automate testing with built-in test sequences Meet standards more easily with pre-configured POLQA and PESQ measurements Simultaneously measure/view up to eight channels on a single screen in real time Configure for specific applications with digital audio interface (AES3/SPDIF and DSI) and Bluetooth audio measurements options
-
product
Audio/ Video
Our experts/ physicist can help you in the Implementation of your algorithms including BPR, NUC , Edge Detection and movement analysis algorithms.Our development environment is based on C++ and LabVIEW libraries or tools such as Vision Builder for Automated Inspection from National Instruments.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Sound Harmonics and Current Analyzer
H74050100
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
Cable Assy 37-Pin D-Type M/F 2m
40-970-037-2m-MF
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
product
Cable Assembly, 160-Pin DIN41612, Male to Unterminated With Tinned Ends, 1m
A1604MR-T-0A100
This cable assembly is not suitable for direct connection to Pickering Interfaces switching products.
-
product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to Unterminated (Tinned Ends), 2m
40-972B-200-2m-FU
This female rear exit to unterminated 2m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to its mating connector by female screwlocks.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-025-0.5m-FU
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, Receiver, 36", Mini Coax, PXI, 28 MCX PLG
540346010252
Cable Assembly, Receiver, 36", Mini Coax, PXI, 28 MCX PLG
-
product
1.5 M 50-pin D-Sub Cable
Y1135A
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.25m
40-977-542-0.25m
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.25m Long.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
A050DM5-F-0A050
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
75 Ohm Mini SMB Cable Assembly
40-977-751-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Cable Assembly, Receiver, 36", TriPaddle, 37 Pin Female DSub, 1000V
540119030201
Cable Assembly, Receiver, 36", TriPaddle, 37 Pin Female DSub, 1000V.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 1m, Screwlocks
A068SMR-C-6B100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Female, 1m
40-970-160-1m-FF
The cable assembly is suited for direct connection to Pickering Interfaces products using a Female DIN41612 connector. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
SHB12X-B12X, 73-Pin, Male InfiniBand to 73-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable 2m
192344-02
The SHB12X-B12X LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS instruments or some NI 658x LVDS Adapter Modules for FlexRIO with other NI accessories such as the SMA-2164 to break out cable signals for direct access. It is a shielded, 100 ohm cable that is offered in various lengths.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 0.5m HV, Exit Towards Pin 1
A050DF5-F-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
