Software
a set of instructions to run hardware and or process data.
-
Product
Vacuum Quality Monitor Systems
-
The 835 VQM is a mass spectrometer that operates from UHV to 10-5 Torr and accurately measures the gases in the vacuum chamber. The 835 VQM Differential Pump System delivers the advantages of the 835 VQM at higher pressures. The VQM system consists of an autoresonant ion trap mass spectrometer gauge, a VQM Controller and VQM Viewer software that that converts raw data into actionable information. The system is ratiometric, meaning that it determines the ratio of each gas to other gases in a vacuum chamber. It is usually coupled with a total pressure gauge to provide partial pressures of each gas as indication of the quality of the vacuum in the chamber.
-
Product
Software Defined Radio Firmware
FWSDR
-
The combination of the firmware FWSDR and the high-end digitizer ADQ14 creates a unique platform for software-defined radio. This 14-bit digitizer provides the high dynamic range needed in an RF environment and the interleaving technology provides high signal bandwidth coverage.The interleaving technology is provided through the use of SP Devices’ proprietary technology ADX which removes typical interleaving artifacts and enables the unique combination of bandwidth and dynamic range.
-
Product
Infrared, Near Infrared and Raman Spectroscopy
-
rom the very compact FTIR spectrometer to the world’s highest resolution: Bruker offers the industry's largest selection for demanding routine and High End FTIR research application including the new and unique verTera cw THz functionality.Process monitoring with FTIR / FT-NIR process spectrometers.A complete line of Near Infrared Spectrometers to fit all your needs, including Process Monitoring.FTIR Microscopy and Raman Microscopy and Spectral Imaging for high sensitivity at high spatial resolution.High spectral resolution, high performance Raman and FT-Raman spectrometers for advanced routine solutions.FTIR Gas Analyzers for the fully automated and high precision real-time monitoring of gas compoundsImaging Remote Sensing systems for analysis of gases, liquids and solids.CryoSAS semiconductor material quality control for photovoltaic and electronics industry.OPUS, the "all-in-one" IR and Raman spectroscopy software consists of a suite of software packages that cover both standard and specialized applications.ONET, software for the setup, administration and control of large FT-NIR spectrometer networks.
-
Product
Configurable Data-Logging System
NI CompactDAQ
Data Acquisition System
This NI CompactDAQ configurable data-logging system includes an NI CompactDAQ controller or chassis, C Series I/O modules, and Chameleon software. It is designed for structural test and monitoring applications with the NI CompactDAQ controller, which includes built-in processing and nonvolatile storage for running Chameleon software and logging data locally. Alternatively, you can choose a USB or Ethernet chassis for a lower cost system that requires an external PC. This system accepts a variety of C Series I/O modules, so you can mix and match microphones, accelerometers, and temperature and bridge-based sensors.
-
Product
ACQUA Compact Systems
-
ACQUA Compact Systems are cost-effective complete solutions for specific measurement tasks. They comprise the compact version of the ACQUA software as well as the corresponding front ends and measurement standards.
-
Product
Embedded Control and Monitoring Software Suite (Subscription License)
-
The Embedded Control and Monitoring Software Suite (Subscription License) helps you quickly respond to the changing requirements of your system with software tools that span between OSs, hardware technologies, and I/O types. With a subscription license, lower the upfront cost of purchasing software by buying access to the suite for a year, with the option to renew.LabVIEW is the ultimate design software to efficiently design, prototype, and deploy applications with hundreds of prevalidated libraries, tight hardware integration, and a variety of programming approaches including graphical development, .m file scripts and integration of C/C++, and Python and HDL code.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
ESD Test Simulator
ONYX16
-
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
Product
COM Express Type 6 Basic Module With Intel® Xeon® & 8th Gen Intel® Core™ Processors And Intel® CM246/QM370/HM370
CEM520
-
The CEM520 is a high-performance COM Express Type 6 basic module featuring triple independent displays, industrial operating temperatures and rich expansions. The CEM520 is based on the Intel® Xeon® E-2176M and 8th generation Intel® Core™ i7/i5/i3 processors (codename: Coffee Lake) with the Intel® CM246/QM370/HM370 chipset. The system-on-module is equipped with dual DDR4-2666 SO-DIMM slots for up to 32GB of system memory. Its wide operating temperature range of -40°C to +85°C strengthens the adaptability of harsh operating conditions. Integrated with Intel® Gen 9 graphics, and with the support of DX11/12, OCL 2.0 and OGL 4.3/4.4, the Intel® Xeon® and Core™-based computer-on-module presents excellent graphics performance with a resolution up to 4K. Three independent displays are supported through one LVDS, one VGA and two DDI ports for HDMI, DisplayPort. The CEM520 comes with multiple I/O connectors including four SATA-600 interfaces with RAID 0/1/5/10, one Gigabit LAN port with Intel® i219-LM controller, four USB 3.0 ports, eight USB 2.0 ports, and 4-In/Out DIO port. Also, the system-on-module is expandable with one PCIe x16 slot and eight PCIe x1 slots, as well as LPC and SMB expansion buses. Trusted Platform Module 2.0 (TPM 2.0) is supported to provide efficient hardware-based data protection. This new powerful COM Express Type 6 module is compatible with Windows® 10 and Linux operating systems. It also supports AMS.AXView – Axiomtek’s exclusive software for smart device monitoring and remote management applications.
-
Product
C Series PROFINET Interface Module
Interface Module
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
Product
Hand-helds
-
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of temperature profiles. For the instruments there are various designs of thermometers available. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software, some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-Cal.
-
Product
3-Slot Data Acquisition Mainframe With GPIB, Three 20-Channel Multiplexer Modules, And BenchVue DAQ Software
DAQ973MBX
Mainframe
The DAQ973MBX Best Multiplexer Bundle offer includes a DAQ973A three-slot data acquisition mainframe, three 20-channel DAQM901A multiplexer modules, and a BV0006B BenchVue DAQ software with a KeysightCare software support subscription. This bundle provides the following:3-slot mainframe with USB, LAN, and GPIB6.5-digit (22-bit) internal DMM60 channels of multiplexer switches6 channels of dedicated current measurements2-and 4-wire scanning300 V switching80 channels/s scanningbuilt-in thermocouple reference junctionbuilt-in signal conditioning measures thermocouples, RTDs and thermistors, AC / DC volts and current; resistance, frequency / period, diode test, and capacitance36-month node-lock BV0006B BenchVue DAQ software license with KeysightCare software support subscription
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
Signal Analyzer
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
Product
Nodal Impedance Analyser
QT-Hi1
-
Qmax Test Technologies Pvt. Ltd.
QT-Hi1 is an innovative Nodal Impedance Analyzer, which uses the industry’s proven V-I trace techniques of learn and compare of nodal impedances which are represented as VI Curves. It uses innovative Auto Best Curve fit technique an intelligent software alogorithm which enables automatic selection of the best fit value of Voltage, Source Impedance and Frequency of the stimulus waveform. The compact size with re-chargeable battery makes it an ideal companion for on-field applications. The wide 8” touch screen graphical display makes this tool more valuable in test and repair industry at all times.
-
Product
Syringe Pump
500xv
-
The 500xv is able to pump higher viscosity material by reducing the restriction within the pump, specially designed with 3/8” ports at a 45 degree angle. Ball valves are used for automating refill and continuous flow which clear easily.The 500xv syringe pump provides precise delivery of high viscosity material up to 204 mL/min. Pulse-less flow is delivered up to 5,000 psi (345 bar) for pumping thick materials. Viscosity can be reduced by heating the pump chamber. A Temperature Control Jacket can be used to raise the temperature above ambient up to 100 ◦C.The High Temperature package allows the ability to heat up to 200 ◦C.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller.The 500xv pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure.
-
Product
Water Samplers: Water Samplers
-
A water sampler is often used in conjunction with a CTD. The water sampler collects 1 or more actual samples of water for analysis in the lab after recovery of the package. The water samples can be used to verify the accuracy of data measured by the instruments on the package, and/or to provide additional information that cannot be measured with an instrument in the field. Sea-Bird water samplers can be controlled (i.e., bottles closed) from deck via a Sea-Bird deck unit and software, or can be pre-programmed to close bottles at desired depths. Sea-Bird manufactures two water samplers: the SBE 32 Carousel (up to 36 bottles, 1.7 - 30 liters, available in regular, compact, and sub-compact sizes, for depths to 10,500 m) and the SBE 55 ECO (small, 3- or 6-bottle sampler for depths to 600 meters).
-
Product
GPIB-RS232, Instrument Control Device - Korea 220VAC
779732-09
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Data-logger
11275
-
Comes loaded with M. C. Miller’s Pipeline Survey software application for “Over-the-Pipe” Surveys:• Close Interval Potential Surveys (CIPS or CIS)• DCVG Surveys• Combined (single-pass) DCVG/CIS Surveys• Surface Potential Surveys
-
Product
Video Microcope
BVM-20101
-
High-resolution CCD sensor, built-in analog/digital converter, analog and digital signal directly display on the screen, can also simultaneously display on TV and computer through corresponding interfaces; taking photo and video through software; easy operation, reducing user's fatigue and injury.
-
Product
Measurement Data Management
-
Top-selling Supported software for visualization of quality. Measurement Data Network SystemMeasurLink
-
Product
EBIRST 104-pin D-type Test Tool
93-022-001
-
The 93-022-001 eBIRST 104-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Data Analysis Software
PV II
-
Software to communicate and display data from PQPro™ Power Quality Analyzer.Can connect wirelessly (Bluetooth) to multiple instruments.View real time data numerically, vector diagrams and analog meter format.View downloaded data in graphical form.Multiple graphical pages can be open at the same time.Graphs can be annotated with data boxes and text bubbles.Graphs can be pasted in to Word or Excel files.Export data in CSV format.Export data in PQDIF format.Export section of data file to PV II format.Generate reports with both graphical and tabular data.
-
Product
Power Analysis Software
PAS
-
PAS is SATEC's comprehensive analysis and engineering software designed to program and monitor all SATEC devices. It includes a variety of additional tools to assist in system setup, such as the communication debugging module.
-
Product
WriteNow! Programmers
-
Based on the proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices (microcontrollers, memories, CPLDs and other programmable devices) from various manufacturers and have a compact size for easy ATE/fixture integration. They work in standalone or connected to a host PC (RS-232, LAN and USB connections are built-in), and are provided with easy-to-use software utilities.
-
Product
ONE BOX
-
Both the Z and X handheld analyzers run on the same software platform, operating system, have the same user interface, same battery, and same charger making training and operation a breeze. Get them both when you purchase the ONEBOX package.
-
Product
For Real-Time X-ray Inspection Systems
Image Processors
-
A number of image processing software packages are available. Features include frame averaging, measurement, text, label, marking, 3-D rendering, video recording and image storage. Additionally, BGA analysis and void measurement software can be added as well as other options. See our image processors for x-ray inspection machines below.
-
Product
Solder Joint Inspection System
-
DMC developed the software to inspect the solder joints of automotive power door lock switches.
-
Product
Motion Control
-
ADLINK motion control solutions have been widely adopted, to date driving over 700,000 axes industry-wide. ADLINK’s extensive field experience has driven the development of powerful, high-efficiency rapid response pulse motion controllers, real-time network controllers such as EtherCAT, Ethernet and MotioNnet, and application-level software for operating control systems with over 400 APIs
-
Product
X.25 Adapters & XOT
FarSync XOT Runtime
-
The FarSync XOT Runtime software provides an API to support applications that previously required an X.25 interface to instead use XOT (X.25 over TCP/IP) as the communications method for PCs and Servers running Linux and Windows.
